Thank you! You clearly defined and showed the jamb and the casing and showed them up close. Then you showed how to measure, again with nice close ups and you announced the measurement while you showed where it lands on the tape. That gave me confidence as to exactly where you were measuring. All the other internet videos show from far away and don't tell the numbers, so you never know what exactly their measuring. Great job!
@vwhwang
3 жыл бұрын
Thank you! By far the best explanation of measuring screen doors I've found after searching through lots of confusing information on the internet!
@lnt1984
3 жыл бұрын
I Really appreciate the way you handled the camera and broke it all down. Thank you!
@JuanSanchez-pi5pj
Жыл бұрын
Thank you sir for taking the time to show us very clearly how to measure for a screen door..I'm in the process of installing one for the front and back door..thank you so much!!
@deborahgoodwin1379
3 жыл бұрын
Thank you sir, excellent video. Very precise with close up measurements so I could see exactly where to measure.👍
@gregoryc5989
Ай бұрын
The best explanation. Thank you
@anthonycantu8879
2 жыл бұрын
Thanks for the thorough explanation. I watched another video where, essentially, he just took a level, a couple of little wooden blocks, to support the door, and before you knew it, it was "up and running," so to speak. It took about half the time of your video, but I'm sure he made a lot of mistakes. But hey, it worked. Some people can do stuff like this in their sleep 💤😴
@purplesuninthesky
2 жыл бұрын
So you would order a 36 x80? Screen door?
@marbel4987
Жыл бұрын
Thank you so much… you’re the best..more power to you and god bless❤
@Kristinapedia
2 жыл бұрын
My house is 90 yrs old. I have the old style metal storm door with the double glass, both replaceable with screens. The casing is 29.5" but that's with the door installed of course. I wonder if I take the aluminum casing off the frame if it will be 30". So, a door that is listed as 30".. is that with the casing or without the casing?
@Bestcustomscreens
3 жыл бұрын
I appreciate your attention to detail and taking your time explaining on this video. I would would have a video like this 30 seconds and probably of missed some important details. I do have a question: Why do you go with the larger measurement on the height? I normally go with the smaller measurement.
@dragonslayer2996
2 жыл бұрын
So yes and no, in screen manufacturing you should always document 3 things. 1. Lockheight you want ( so as to not interfere of pre existing hardware or to replace screen already there in same holes) 2. Not any difference in HWS ( Height, width and square) 3. Build out or stops required.
@maikarokobukai435
2 жыл бұрын
Thank you for the very clear information...
@somethingbeautiful2212
2 жыл бұрын
Thank you! That was very clear 🙂
@dennisbadger7424
Жыл бұрын
Great video. very helpful.
@marylamb7031
9 ай бұрын
Thank you so much. You are the best. I fully understand now.
@coganblaster
Ай бұрын
So, what size door would you order?
@Joe-em3iw
2 ай бұрын
how to put door frame in an opening that is 80 1/4 if your door is 80 and 5/16? Just pound it in?
@michaelbarcz326
3 ай бұрын
Glad donny realized that big clipboard would be a nuisance. Helpful tho!
@proton.electric
2 жыл бұрын
Yo Agradezco su atención a los detalles y su su tiempo explicando en este video. me gustaría tendría un video como este 30 segundos y probablemente se haya perdido algunos detalles importantes. I tengo una pregunta: ¿Por qué vas con el medida más grande en las alturas que normalmente ir con la medida más pequeña.
@j.c.1902
3 жыл бұрын
Shouldn't you use the longest distance instead of the shortest? I always measure in centimeters and then convert it. I am not good with the fractions.
@SarahDigsHockey
3 жыл бұрын
I don't want to install a screen door, I just want to replace one that's broken. So can I just measure the door? If so, what are the chances that I'll find the exact measurements at the store?
@donnysdoors254
3 жыл бұрын
Yes you can measure just the door. The store will carry What is called a door blank. It will need to be trimmed to fit most of the time. I make custom screen doors so this video gives my costumers instruction of the proper way to measure. I send them down a door that is a close fit needing little trimming.
@melonienoel9692
Жыл бұрын
THANK YOU!
@shethinksclearly1372
Жыл бұрын
Thank you so very much
@futbol1972
11 ай бұрын
The casing of my front door is about 1/2" will that be enought to install security door? I saw another video where he said casing needs to be a minimum of 1'? House was built in 2005 in clovis ca
@Joe-em3iw
2 ай бұрын
You will have to trim it.
@johng8888
2 жыл бұрын
Good luck 👍
@charronfamilyconnect
3 ай бұрын
Is it 35 and 12-16th wide not what you wrote at end of video
@diverdave4056
2 жыл бұрын
this video could easily be trimmed by 6 full minutes
@j2collinwood
Жыл бұрын
Something happened when you measured the bottom, I noticed you weren't the same hopefully you're alright.
@swav100
5 жыл бұрын
I have a sidelight so the casing doesnt have a jamb how do i go about this
@donnysdoors254
4 жыл бұрын
Treat the side light as a casing, If I could post a picture here it would be great done it many times.
@MartinLopez-ys5dm
6 жыл бұрын
Donny, why do you subtract 3/16 from the 15/16? (Sorry I suffered a TBI, I can't think right sometimes).
@homie817x
6 жыл бұрын
probably for the hinges
@MrSiobhancolleen
5 жыл бұрын
Donny, I am curious to know the answer to this question as well.
@slimdougmaddox4634
5 жыл бұрын
To allow for the door to swing. You're making a door, not boarding up the opening.
@cynthiajennings7875
5 жыл бұрын
Ditto! if you're going to make a video, give us the reasoning behind making it 35 3/16. My measurements are 32/31.75/32 Do I make the door 31.75" wide then?
@lindanwfirefighter4973
5 жыл бұрын
He gave the reason at 5:10. Because it allows a slightly off kilter doorframe to fit the door.
@Philrc
4 жыл бұрын
are you using cm or inches?
@absentehhh8263
4 жыл бұрын
Inches
@karenholt8441
4 жыл бұрын
The noun form of broad is breadth, the noun form of long is length, and the noun form of wide is width. Because of this, some people follow the pattern and say heighth, with a th at the end of the word high. That is not standard English. The correct form is height.
@mdoDesignerMusician
4 жыл бұрын
You may be correct, but is it necessary to post that? That has nothing to do with the point of this video.
@karenholt8441
4 жыл бұрын
Matthew Oakes - It’s a teaching moment. Nothing else implied.
@donnysdoors254
3 жыл бұрын
@@karenholt8441 We are a Yankee family here since the king of England granted our land. I remember the original dialect in my youth that has since diapered. My English is the product of spending more time in the woodshop than in school . I thank you for your teaching, and will try to put it to use. Thank you! Donny
@retromoviefan944
5 жыл бұрын
so, most standard screen doors that you can buy at Lowe's or Home Depot are 30, 32, 34 or 36. Is he saying you'd have to order a custom door? As in his example here, could he buy a 34 inch wide door and make it fit, or what?
@njfabio1
5 жыл бұрын
Yeah... Most of the time, you can rip qual amounts off. However you will not obtain the same width of board all around.
@pmny3423
5 жыл бұрын
Yes. You round down and then fill in the gap with moulding.
@PoolarityChannel
5 жыл бұрын
Those standard size doors are not absolute sizes, they "usually" have tolerances that are +/- 1/2" so a door advertised as a 32" door will fit a 31.5" width and up to a 32.5" width. Download the installation manual first, before you buy and make sure that is what the manual itself states.
@donnysdoors254
3 жыл бұрын
I make Doors to fit openings with minimal but necessary trimming, This video also tells a person how to write down on a paper they can carry to the store to find a appropriate blank.
@donnysdoors254
3 жыл бұрын
If I had to buy I would buy bigger then fit & trim. doing otherwise would restrict the opening.
@benavila6345
4 жыл бұрын
forgot to check for square
@donnysdoors254
4 жыл бұрын
The blank cant be made unsquare. Thats why the tolerence for trimming.
@dragonslayer2996
2 жыл бұрын
@@donnysdoors254 all screen doors can be made out of square?
@howimade3309
5 жыл бұрын
lol did you seriously measure 3 spots...so if youre off by 1 inch what are you goona do? go to lowes and look for one thats has the option for ppls homes with door jams thats off by 1 inch??
@beeughhgoodhuman2726
3 жыл бұрын
Dirty sales trick he will tell the customer that he has to order a custom door which will cost more money. But just order the standard 36 in door an make that fit just fine. He's a douchebag and a typical salesman
@SensSuck
3 жыл бұрын
@@beeughhgoodhuman2726 You use shims to make it square. Not exactly complicated guys.
@fredbarrera1174
Жыл бұрын
🤦🏽♂️🤦🏽♂️🤦🏽♂️
@Lucas-nz9kz
29 күн бұрын
Wrong the exterior trim is n😅t called casing it’s exterior trim but that trim is a stucco molding. The stucco molding is being use for the lap siding. You flunk my clase.
@cynthiajennings7875
5 жыл бұрын
why is the door width 3/16 smaller - need explanation!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Is it for the hinges? Is it 3/16 smaller than the smallest measurement? 32/31.75/32 Then you did the math on the bigger number. Why? I plan to make the screen door myself so these details are important. Thanks
@pmny3423
5 жыл бұрын
Door needs to be able to swing open. For this it needs clearance.
@inspectrgajit
4 жыл бұрын
3/16 will be enough space for the thickness of the screen door to clear the casing on each side.
@dphenomenon
2 жыл бұрын
"Height" please!-- there is no "th" @ end but an "ht". The consonant sound produced by "th" is as pronounced here....improperly since the spelling is rather an "ht" suffix which is tten just a regular "t" sound. Grammar is major for me so correct please. Your content is great and I've saved it.
Пікірлер: 66