Viewing from Trinidad & Tobago, always looking for informative Sheet Metal Layout videos and I recently found yours. Thank you for sharing.
@brownEmmet
Жыл бұрын
Explained in great detail! Looks so easy on you, truly a master of his craft!
@choruzvargas4009
Жыл бұрын
They have faster ways this is not it 🤣
@brownEmmet
Жыл бұрын
@@choruzvargas4009 Where is your channel, apart from stupid sayings i don't see anything. Before you let your envy run wild, make it better. Have a good time.
@neilbates4111
7 ай бұрын
I was an apprentice trained sheet metalworker when we made a pattern we normally made the bend 5 and two halves pattern because the pattern could be used for a 90 bend 75 60 45 30 15 degree bends
@TOPOnyHbKA
Жыл бұрын
Exzellent. Als ich mir den Prozess der Teilemarkierung ansah, erinnerte ich mich daran, wie ich an der Universität einen Kurs in Darstellender Geometrie und Technischer Grafik belegt hatte
@marceloalves5804
6 ай бұрын
Good morning! I'm from Brazil, congratulations on your videos! They are exceptional!
@norbertschneider2571
Жыл бұрын
Hello. Thanks for those videos its helping a lot. Greeting from Hungary.
@AM-dn4lk
Жыл бұрын
That was awesome. Thank you for sharing. You are a master sheet metal worker.
@muhammedatifsuleman8975
Жыл бұрын
Hi , There i was searcihing this from morning and found you. thank you very much it help me to under stand the fabrication process. Thanks again , it was a quite help, thanks again for sharing
@valentinlishkov9540
Жыл бұрын
free:
@JoeAngulo-ps4dz
Жыл бұрын
You are very good ....thank you for sharing and making this video.
@joelmwangi456
Жыл бұрын
great work sir
@Sheet_Metal_Workshop
Жыл бұрын
Trank you
@justinsinkala
Жыл бұрын
Nice work brother man
@vaijur5194
Жыл бұрын
Thanks, really good video. Good explanation
@carlosconcha8115
3 ай бұрын
Muy buen trabajo amigo saludos desde Chile.
@hafateto
Жыл бұрын
Amazing 👏
@yusufterzii2
8 ай бұрын
I live in Turkey and no craftsman here will teach you how to do the job because they always want to be the wanted man. The craftsmen here think that if they teach you how to do it, you will take away their business and that's why they don't teach you. I learned how to cut and make an elbow template in just three days, I wish your videos had a Turkish option.
@Sheet_Metal_Workshop
8 ай бұрын
Maybe try substittle on Turkish
@yusufterzii2
8 ай бұрын
@@Sheet_Metal_Workshop I tried but there is no translation into Turkish
@hamitcnk3323
7 ай бұрын
Yusuf kardeşim sen ustaya denk gelmemişsin maalesef
@yusufterzii2
7 ай бұрын
@@hamitcnk3323 abi ben bu sektörde yapılan işi beğenen adam görmedim havalandırma yaparsın yanında tesisat bilmeni isterler ,tesisatı da yaparsın elektriği isterler , birini biliyorsan da işverenin gözünde bu nasıl usta konumuna düşüyorsun iş tanımı yok iş beğenen yok
@hamitcnk3323
7 ай бұрын
@@yusufterzii2 sende haklısın
@Inquisitiv3Mind
12 күн бұрын
You are really mastered your work. But i did not understand measurements.andnhow it can be 120radius from 90 mm.pipe .i am.confused..
@fernandosilvafilmmaker2625
Жыл бұрын
hello, thank you for your videos, is there any store on amazon where i can buy some of these tools, for example this drill pliers?
@mesininjeksiplastikkorea6703
Жыл бұрын
Good job sir
@judithmariun3667
9 ай бұрын
Thanks and great ...I like these jobs but I havn't technical ideas..Now I trying to learning from your great lessons ...
@Sheet_Metal_Workshop
9 ай бұрын
👍🏽
@modricaninmodricki7559
Жыл бұрын
Ja sam nekad radio izolaciju u njemackoj kad sam bio mlad.Sad zadnjih 22 godine radim u Americi.Ovdje je sve mnogo losije uslovi rada, masine , material. Jedino se dosta bolje placa neg u njemackoj.Sto se tice videa stvarno ste talentovani gospodine.
@Sheet_Metal_Workshop
Жыл бұрын
Hvala druže trudim se da pokažem svoje znanje
@modricaninmodricki7559
Жыл бұрын
@@Sheet_Metal_Workshop u kojem gradu radis?Ja sam nekad radio za G und H ja mislim da se tako zvala kompanija iz Gelzen Kirhena a Imala je filijale I u Bambergu I drugim gradovima.
@Sheet_Metal_Workshop
Жыл бұрын
@@modricaninmodricki7559 evo mene u Gelsenkirchen živim , već od 1996 pre toga sam živeo u Rotterdam pozdrav Zemo
@modricaninmodricki7559
Жыл бұрын
@@Sheet_Metal_Workshop Znaci ti si razlog sto Salke 04 kuburi na dnu tabele,tamam od 96 je njima niz brdo krenulo.Mene je 1996 protjeralo iz njemacke. Ja sam zivio u Aachenu a radio vecinom po istocnoj njemackoj I Frankfurtu.Pozdrav I tebi zemo I cuvaj prste .
@fcwins6400
8 ай бұрын
Ur a legend for this
@uwejanssen9601
Жыл бұрын
perfekt erklärt und umgesetzt.so habe ich es auch gelernt, bevor die Maschinen es uns abgenommen haben.aber sehr gutes Handwerk,wie du es zelebrierst wird immer bei uns isolierern wichtig sein.tolle arbeit, perfekt erklärt.danke dafür
@Sheet_Metal_Workshop
Жыл бұрын
Gerne und schöne Grüße
@HumayunKabir-ii1vo
4 ай бұрын
Thise are very usful video. Thanks you.
@JahidulIslam-tb2pj
Жыл бұрын
Good job
@albertosantistebanaricoche9917
Жыл бұрын
Bien. Maestro un traslado desde Perú Alberto santisteban a
@jeffsmith5084
Жыл бұрын
Just discovered your channel. So much good stuff. I notice a number of hand tools I have not seen locally in Australia. Can I suggest you think about a video featuring them? That little scratching tool and the squares with flanges in particular. Where would we get those?
@Sheet_Metal_Workshop
Жыл бұрын
It’s in my plan to do a hand tool video
@Sheet_Metal_Workshop
Жыл бұрын
Or check this. kzitem.info/news/bejne/lHh32nakoIt-o6w
@yunusshaikh8388
Жыл бұрын
000
@yunusshaikh8388
Жыл бұрын
90
@nevenrakic8466
Жыл бұрын
Legendo , opet te žena pustila da se igraš 😂. Pozdrav i svaka čast,rođen si za profesora.
@mwaseemwr2836
Жыл бұрын
good job
@alankmicicki6795
Жыл бұрын
Hi great videos as always have asked before when making valve boxes no you show Swager for joining boxes together in video but could you show the wheels you use on the Swager as can't see them clearly on video cheers
@Sheet_Metal_Workshop
Жыл бұрын
I will make a video with those weels an so them properly with explain
@tarlanismail5029
2 ай бұрын
thank you very much for your help🔥🔥🔥🔥🔥👍
@thornwarbler
8 ай бұрын
Superb.Danke.
@defekts
Жыл бұрын
That tool you inserted into the holes to hold the swag instead of using screws would you be able to tell me what it’s called or even better link me please? Fantastic video and very detailed, keep up the great work 😬
@gazikaraman8171
Жыл бұрын
Gread thank you 🙏🏻
@arnelaparece7916
Жыл бұрын
Thank you sir
@shaneringrose9416
Жыл бұрын
Thank You
@ekodubek7516
Жыл бұрын
Lot of work to make one segment elbow. At the end it looks like done by automated machine with no human hands involved. How much time it takes for you to make one like this normally with "no camera" ? Great job!
@garybrewis2743
8 ай бұрын
I have just started an apprenticeship your videos should help me along the way
@Sheet_Metal_Workshop
8 ай бұрын
👍🏽😀
@DungNguyen-xq1tl
Жыл бұрын
Có cách để quay compa theo đường tròn không bạn
@mwaseemwr2836
Жыл бұрын
Very nice you are video
@onixcual
7 ай бұрын
Sr sorry to ask but, what kind of electric shear is that? thanks in advance for your answer, :)
@mimempayar5776
Жыл бұрын
with math, it was soo amazing..
@kanniewillie6221
4 күн бұрын
Hi I always enjoy watching your videos. Please advise on how to cut PIR pipe sections insulation to fit on a 90 Degree elbow. The insulation is a double layer 50mm + 50mm and the joints must be staggered. Could you make an example pipe OD 219mm. Long radius elbow 1.5D. Any help is appreciated. Thanks.
@Sheet_Metal_Workshop
4 күн бұрын
Hi, will make a segment bend out of metal and use it as a template pull it over the PIR pipe and cut it left and right so I have a seam in the throat and in the back ( 2 part), and repeat the same with a bigger segment where the seam is left and right so you have it staggered only in the circumference on the finished segments, I hope I explained well
@nathan-jamesthompson9867
11 ай бұрын
Hi There! Love your videos, super informative, could you please let me know what those things are used to secure the bend instead of screws? 37:37 in the video, thank you!
@Sheet_Metal_Workshop
11 ай бұрын
There will be a video about tools and also a link where to buy
@nathan-jamesthompson9867
11 ай бұрын
@@Sheet_Metal_Workshop thank you very much
@jomarzordik2207
4 ай бұрын
Awesome..😊
@kamalkhan4445
Жыл бұрын
Nice
@jhonnypereyranieto4853
7 ай бұрын
Good morning, thanks for the very good video, could you tell me the name of the tool you use to mark the iron, with which you marked the long edges, thanks.
Thanks, I learnt a lot from this. One thing is still puzzling me - why is it a 3-part bend when it requires 4 parts to turn 90˚?.
@Sheet_Metal_Workshop
Жыл бұрын
Because it’s made out of 3 segments 2 complete segments and 2 half (2x half is one)
@flxchanel6921
6 ай бұрын
Im from Indonesia,thanks mr
@bbtajmahal137
Жыл бұрын
Здравствуйте,как называется ваш угломер транспортир?
@paulohenriquesampaio6243
Жыл бұрын
Por favor me dis onde encontro dese compaso para comprar qual sait ?
@marceloalves5804
6 ай бұрын
One question, the 5 millimeters margin, should I leave it on both sides or just one side? In the detail specified at 10:53 in your video. Thank you very much in advance!
@Sheet_Metal_Workshop
6 ай бұрын
The 5 mm is for both sides you have 2swages but on the layout I only show it for one side (half) so wenn making your template you have automatically for both sides
@marceloalves5804
6 ай бұрын
@@Sheet_Metal_Workshop Thank you very much!
@kd6275
Жыл бұрын
Was ist dieses blaue Ding, womit du bei der abwicklung des Fisches die einzelnen Punkte verbindest? Diese blaue Gummi artige Teil? Sieht sehr hilfreich aus und man kann damit bestimmt Zeit sparen :) Grüße vom Bodensee
@Sheet_Metal_Workshop
Жыл бұрын
Das ist eine flexibles Kurven Lineal
@zulhaikalzikri1842
Жыл бұрын
What happened if the elbow radius is shorter than the OD of the pipe?
@Sheet_Metal_Workshop
Жыл бұрын
Then you can make a cheat bend or a 90 degree elbow 2 parts , check my channel for the video’s
@abdurraheem2439
Жыл бұрын
@@Sheet_Metal_Workshop ❤
@BulentKarakuzu
4 ай бұрын
İ say really for your video. İt is soo helpfull for me. Thanks
@Sheet_Metal_Workshop
4 ай бұрын
👍
@jaimecalero6938
Жыл бұрын
Está muy excelente sería bueno traducir en español
@javierhugodiazparedes3497
Жыл бұрын
Buenas maestro Un saludo desde Perú Como haría usted un codo de radio corto Osea el aislamiento mayor ala tubería
@Sheet_Metal_Workshop
Жыл бұрын
Watch My Other video cheat bend
@Sugreevnishad
Жыл бұрын
Please give a tips for big size fabrication to small version.
@pioterwil410
Жыл бұрын
Got one question about radius of the elbow or pricisely how to measure it when i can see the pipe and then im coming back to the work shop to make it? Do you measure it in the throat from weld to weld or is it a measurment from the axis of the pipe? Thanks and keep it up mate. Love waching your videos
@barnabuswafula476
11 ай бұрын
Me too would like to know how to get small radius without measuring on pipe welding
@rolandoortega3300
Жыл бұрын
What is the name of the tool you use to mark the line of work? at minute 3:15
I don't understand how that camera works, it went inside the 90?
@vinuvsa1503
Жыл бұрын
I think used tiny camera
@nazkatbhatti467
9 ай бұрын
Thanks very much
@Sheet_Metal_Workshop
9 ай бұрын
👍🏽
@odacreations4080
Жыл бұрын
Thabk you for sharing sir
@Sheet_Metal_Workshop
Жыл бұрын
👍🏽
@lotfitrene366
Жыл бұрын
Thank you for this video. I recently subscribed to your channel. Your question is how to find out the number of pieces
@Mamii33-.-
2 ай бұрын
Adamım bu işi çok iyi yapıyorsun ve seni izlemeye devam edeceğim bu işte usts olmak istiyorum ❤
@Sheet_Metal_Workshop
2 ай бұрын
Alıştırma mükemmelleştirir, size iyi şanslar dilerim
@kevlofty1
8 ай бұрын
Hi video are great , please could you make one about 90* bend with a flat on side . Sheet metal working in Australia
@Sheet_Metal_Workshop
8 ай бұрын
I see what I can do
@paraibacurticoes
Жыл бұрын
Precisa aumentar algum acréscimo por causa do friso?
@Sheet_Metal_Workshop
Жыл бұрын
Eu me dou mesada para a conta
@rjreality9484
10 ай бұрын
Sir you are the best ❤ Chargeable sheet cutter that you have used your video what's the name of the machine? where I'll get ?I'm from India city of Kolkata
@Sheet_Metal_Workshop
10 ай бұрын
Hi look here www.bueromarkt-ag.de/blechschere_bosch_gsc_12v-13_professional_akku,p-0601926108,l-google-prd,pd-b2c.html?gclid=CjwKCAjwwb6lBhBJEiwAbuVUSnxrWjiWwFw5zv45YRfA3EOyXlXULpEfZxCxJ0Zd2TDXqCLwJtNKzhoCc98QAvD_BwE
@tooropabel1581
8 ай бұрын
You're the best
@user-ul2eu6lo2f
8 ай бұрын
❤ Bravo
@dikskapidmjbmechanicalengg3271
Жыл бұрын
Hi sir do you have a sheet metal worker books i'm very interesting to know all layout i am sheet metal also but my experience and knowledge few for fabrication
@Sheet_Metal_Workshop
Жыл бұрын
Join facebook.com/groups/926259107475505/?ref=share Here is a lot of books and experience for share
@dumitrupuscasu5688
6 ай бұрын
I like your lesson. for Romania, i don't understand where 100millimeter comes from min 2,15, for D= 200mm, what value do i add to dn. Is a T elbow possible? Thank you.
@Sheet_Metal_Workshop
6 ай бұрын
The 100 is 2x50mm insulation
@dumitrupuscasu5688
6 ай бұрын
Thank you. To understand that we have an elbow with d=80 with 50mm insulation for which we execute an elbow d=190mm. About the execution of a T what answer do you give me? I want to build a rocket stove with thermal mass. @@Sheet_Metal_Workshop
@philipkwakye8584
Жыл бұрын
Morning My Teacher, Please what is the radius of 4"& 6" pipe
@philipkwakye8584
Жыл бұрын
Please kindly explain to me how you got the 3"pipe radius which is 120mm
@Sheet_Metal_Workshop
Жыл бұрын
There is a pipe List and the real Radius is 114 mm so I round it of on 120 mm radius
@user-oc1du9iz8j
10 ай бұрын
Your tutorial is great, can you make a film how to do 45° and 30°? And how to draw 2 part 90°?
@Sheet_Metal_Workshop
10 ай бұрын
Hi i have made a video about that what you looking for check it out if it is useful kzitem.info/news/bejne/lHh32nakoIt-o6w
@tanja2108
Жыл бұрын
Kolega mozes li napisat koju ziknu koristite za koji promjer,hvala
@Sheet_Metal_Workshop
Жыл бұрын
Pie 80-120= 00 130-180= 0 190-230= 1 240-300= 2 300-400 = 3 410- 500=4 Ovo je odprilike Sve zavisi kako ko sihnu stavi Važno da se ne raspadne kad sastaviš segmente
@shohelrana2077
5 ай бұрын
Where are you from?
@jonathannunez-nt2np
Жыл бұрын
how did get that radious?
@Sheet_Metal_Workshop
Жыл бұрын
You can measure it by yourself from Center bend to the weld seam , or there is a list , I used nr 3 dn 80 radius 114 round off on 120 mm www.isosysteme.de/wp-files/Tabellen/deutsch/Radien.pdf
@iorhembaterlumun4126
11 ай бұрын
What if you have 40mm insulation or bigger than 50 because you added up 50mm to be 100mm so what of you your insulation thickness is 65, 75 or 115
@Sheet_Metal_Workshop
11 ай бұрын
Hi For example if the pipe is 89 mm and the insulation is 115 than the diameter is 319 round of 320 What I do is diameter 320 divide by 2 + 30mm makes a radius of 190 a 3 segment bend That’s an alternative Works mostly but not always
@sivab.e7279
Жыл бұрын
This circamram 597mm this step I no understand pls tell mee bro
@Sheet_Metal_Workshop
Жыл бұрын
You mean circumference ?
@shakirhasandriver
9 ай бұрын
Hello sir,i am from BANGLADESH,i can't understand how you get The gero point, would you please help me to get out the problem,
@Sheet_Metal_Workshop
9 ай бұрын
What do you mean? How to find radius?
@dragonesel89
Жыл бұрын
Hallo kannst du mir erklären wie man ein Bogen misst ? Kapier das mit dem Radius nicht…
@Sheet_Metal_Workshop
Жыл бұрын
Hallo Geplant ist ein Video darüber
@rodolfocuero9458
Жыл бұрын
hello teacher could you please explain why if the radius is 114 use the radius of 120mm
@Sheet_Metal_Workshop
Жыл бұрын
@@rodolfocuero9458 i have round of the size
@saulirajala4650
Жыл бұрын
How about triangle elbow next video Good videos Mann🙂
@Sheet_Metal_Workshop
Жыл бұрын
You mean this? Dreiecks Abflachung am Bogen kzitem.info/news/bejne/16aryapqnpVia3o
@saulirajala4650
Жыл бұрын
Thx
@arnelaparece7916
Жыл бұрын
Sir tich me how to calculation of dome spherical...
@Sheet_Metal_Workshop
Жыл бұрын
It’s on the” to do list “
@Dks2234
Жыл бұрын
Eccentric dummy support lay out sheet metal fabrication farmull please upload
@gertjanschutte-rx4ti
Жыл бұрын
Hei als ik een hele grote bocht moet doen en alles gedeeld door 5 doe om de schets klein te houden. Kan ik daarna de 7 getalen maal 5 . Kom ik dan op het zelfde uit
@Sheet_Metal_Workshop
Жыл бұрын
Dat is dan schaal 1:5 Dat kan , altijd vanuit de originele maateenheid uit gaan Je kan zo elke uitslag maken
@karenils8987
3 ай бұрын
How about long Radius?:)
Жыл бұрын
E? Greetings Master!
@Sheet_Metal_Workshop
Жыл бұрын
Od Erdolije do Tokije😄
@Sugreevnishad
Жыл бұрын
Hello! boss how are you?
@rizals1613
3 ай бұрын
I don't understand radius 114 becomes radius 120? where do you get 6 mm? someone please explain to me 🥺
@Sheet_Metal_Workshop
3 ай бұрын
I have rounded off from 114 to 120mm ,but you can use 114 Also
@Inquisitiv3Mind
4 күн бұрын
And where from did you got 190 diameter..and why 50 unsilation became 100..and if radius x then diameter 2x ?
@Sheet_Metal_Workshop
4 күн бұрын
I have round it of
@Inquisitiv3Mind
4 күн бұрын
@@Sheet_Metal_Workshop how does that round of sytsem work? How did u got 190
@Sheet_Metal_Workshop
3 күн бұрын
@@Inquisitiv3Mind the pipe is 89mm plus 50mm insulation that makes a diameter of 189mm so I round of 190mm
@junebrooks665
8 ай бұрын
bloody long way of developing a lobster back
@ElvisyonderMunozamplez
22 күн бұрын
Se puede traducir el video a Español
@valentinlishkov9540
10 ай бұрын
line intersect a toroidal surface
@ManuMonem-jg2df
7 ай бұрын
👋
@arnelaparece7916
Жыл бұрын
Hello boss
@abdurraheem2439
Жыл бұрын
597+30 overlap Where you find 597mm
@Sheet_Metal_Workshop
Жыл бұрын
Diameter = 190mm Circumference = 190x3.14= 596.6 round of 597 + 30mm overlap = 627 cut size for metal
Пікірлер: 214