I like at intro the 3d animation. Your job is always PERFECT ! Bravo my friend
@gerry343
Жыл бұрын
Nice bike!
@freiheitfur2takte354
Жыл бұрын
Perfect Work 💪
@trialetcompagnie4481
Жыл бұрын
Nice job ❤
@yodasbff3395
Жыл бұрын
Nice work. 👍
@DolezalPetr
Жыл бұрын
niiiceee, garant tools, lovely stuff
@nicolasg8233
3 ай бұрын
super
@nunesmotos351
Жыл бұрын
Trabalho muito bem feito nota dez
@andrezaoyt6122
Жыл бұрын
Parabéns... Você é exageradamente bom...
@anonymously241
Жыл бұрын
This is way to easy for you PhoL 😂👍
@peter6782
5 ай бұрын
Lol so much for procision, when you still have to hit it with an hammer even after all the grease 😅
@madmarc
Жыл бұрын
Very nice. Any way to fix worn splines where the kick start lever slides onto the kick shaft?
@PaulXchannel
Жыл бұрын
just weld and machine again
@rclavier
Жыл бұрын
it's fantastic, i have the opportunity during my holidays to practice with my friend on his milling machine... where do you find the materials? how do you choose the materials? thanks to you
@ackiid
Жыл бұрын
Yes, please
@andreasjonsson8075
Жыл бұрын
Would have been cool to see you put a grease point on the kicklever
@theo_korner
Жыл бұрын
About what RPM did you run the reamer? 200-ish?
@PaulXchannel
Жыл бұрын
150
@RODRIGONICOLASVILA
Жыл бұрын
👍
@talltom1129
Жыл бұрын
All I need now is a lathe....
@Ggreg1962
Жыл бұрын
And a milling machine
@sloppyoppie
Жыл бұрын
99 problems in life and this actually it is one on my '81 xr500r. .....But w/only minimal tools and lacking flowage of fettia, I am going to chuck it in the vice and hammer away w/the 5lb'r. We'll see if that'll help it.
@sloppyoppie
Жыл бұрын
I've been getting by with a magnet zip tied onto my frame. Keeps er in check!
@dc6233
Жыл бұрын
@@sloppyoppie When I was broke and had very limited tools, I'd often use an arc welder and build things up, then file it smooth, was the best I could do. But then the ball and spring could keep it in place again.
@jothain
Жыл бұрын
@@dc6233 yeah, this is legit and actually quite good methods as welds are very hard. Done something like few times with success
@dc6233
Жыл бұрын
No one greases their kickstarters or their brake pedals, I can't stand sloppy controls. I wonder why Husky started with such an oddball metric size? Couldn't even be 11.5mm because the pin was bigger than that and it couldn't be 12 because the holes were smaller than that! It certainly wouldn't be a standard size either being a Husky... Love your work brother, you'll be glad we aren't neighbors because I'd want to fine tune my skills with your help!!
@jothain
Жыл бұрын
No one? Speak for yourself.
@PenttiHinikka
Жыл бұрын
I maintain everything on my bike. And I love these videos
Пікірлер: 29