First thing u learn working on Sloan Flushometers... never use pliers with serrated jaws on fixtures with chrome finish. Always smooth jaws
@damong4906
Жыл бұрын
or put something on it a rag or towel
@ParkSideOfTheMoon
3 жыл бұрын
Bless this video! Watching it while sitting reverse on a toilet I had no idea how to fix. Thank you thank you!!
@goldiebk1391
6 ай бұрын
This video just helped me ace my interview for a job making 60k 👊🏽
@123logger
Жыл бұрын
Very good video. A lot of knowledge and insight without a too much talking.
@grahamworksconstruction
2 жыл бұрын
Still leaking in back a little but over all the right thing. I would have cleaned the spud valve and washers with soap and water. Some times you just need to replace it. That wobbly toilet doesn't help. Good jon
@Flushometer_AirConditionerFan
2 ай бұрын
Awesome work there bro 👍🏻 I see that the toilet is a ProFlo and I'm not too keen on that brand!
@chuckgutteridge7175
2 жыл бұрын
When they leak from the joint just past the control stop? Remove the o ring. Sand or buff all corroded metal smooth, grease heavily the o ring groove seat, reinstall o ring carefully., reassemble. So far has stopped all of them unless the oring is damaged. Torn, thin spot, splits etc. Replace o ring and stop the leak.
@kennethdegruchy5503
3 жыл бұрын
How much is too much tightening of the spud nut? A fresh soft and tacky spud gasket should not need excessive tightening which God forbid can crack the toilet. also don't forget flat jawed wrenches for the chromed and very soft brass Sloan valve fittings.
@drumtwo4seven
2 жыл бұрын
where's your instructional video you recorded edited and uploaded to KZitem captain obvious ? captain obvious vs the proverbial armchair quarterback
@Chocolealtadgaming
10 ай бұрын
Thank you I fixed my first toilet with your help
@simmi3647
10 ай бұрын
Thank you. On the same toilet watching this fixing it right now.
@RussellHarrisOfficial
2 жыл бұрын
Thanks David, had the same issue. Very helpful!
@robertoperezrojas2044
4 ай бұрын
Excellent explanation. Thanks 🙏
@raulgutierrez5920
3 жыл бұрын
Good job man!!!👍👍👍👍
@HaloGTMaster94
7 ай бұрын
Nice 👍
@erlendkimmich9448
Жыл бұрын
great. Thanks for posting. Very helpful!
@eduardoa4493
Жыл бұрын
Thank you for the video, I gotta fix one of these tomorrow 👍🏼😎
@exp1993
5 ай бұрын
Thank you for this video!!
@drumtwo4seven
2 жыл бұрын
Good Stuff thanks for uploading 👍
@diyjohn9584
2 жыл бұрын
How long did that repair last? Reusing old parts that was leaking might buy a few weeks, but I hope you went back with new parts for longer lasting repair.
@shellz600
Жыл бұрын
Ive repaired flushometers like this before and i will say that sometimes the parts arent defective when the material leaks. Sometimes the rubber washers become displaced due to people flushing with their feet or pushing up against the flushometer when they sit down. Ive done this exact repair and just took everything apart washed the washers and fittings and then put it all back together, that action buys me an extra 2 yrs life before i have to replace the material.
@thecamper2887
3 жыл бұрын
Nice job
@0008rrc
8 ай бұрын
Thank you !
@banjo3333
Жыл бұрын
thank you man
@KPLovesYou
Жыл бұрын
Where are you from I need you to fix two of them .
@patony_1288
6 ай бұрын
I would've never use the same old rubber gasket, Even if the old one looks good, It's always better to change it, Also you should know that everything looks fine now, (NO LEAKS), Until you leave, Plumbing is tricky like that, It's gonna wait until you step out that door.........Then,..... Wammo.😊
@ryanperry9838
9 ай бұрын
Smooth jaw wrench!
@jasonmartinez5116
8 ай бұрын
Or use a towel or microfiber cloth to cover up the chrome if you don't have smooth jaws
@cortez1638
2 жыл бұрын
Lazy "plumber" smh
@libsrmarxist
2 ай бұрын
When I encounter a leaking spud coupling they are almost always rusted. That's why I carry half a dozen in my truck at all times.
Пікірлер: 34