This is some amazing! Speeduino will be 2020´s megasquirt!
@christiandubrule3507
2 жыл бұрын
You rock and thank you for your amazing contribution to the world of diy efi. I was and arduino fan as mechanic and since speeduino I've built a 408sbc boosted and you better believe speeduino is the heart and soul. Amazing product and only prob now is everything I own should be efi now. Cheers Josh
@hippopotamus86
6 жыл бұрын
For those wondering. Up to and including 0.4.3, the MAP sensor goes with the hole on the top. They for some reason changed this in 0.4.4. I just desoldered and resoldered mine for no reason :(
@hippopotamus86
6 жыл бұрын
Josh Stewart no problem! I should have read the wiki page carefully the first time. Great board by the way, I had the idea of using an arduino as an engine management system and came across the speeduino when I was researching it. You've done way more work on the board than I could have the patience for. Although we are getting some plug and play boards made up for certain engines just like someone has done for the mx5 already.
@George_fitness69
Жыл бұрын
When assembling, for example if I’m doing the first pack of resistors, do those resistors need to go to a specific place or do all resistors in one baggy work universally with every resistor labbled on the bag?
@ndog1234765
Жыл бұрын
Just match the numbers. If it's marked on the bag, just do it. It's pretty easy
@ramanathansubramanian1616
6 жыл бұрын
Sir..When will the speeduino v0.4 assembled board be in stock for sale?? I need one...
@nswbassman
8 жыл бұрын
Can't wait until the next video!
@kickboxer7665
4 жыл бұрын
Will I be able to use an UNO to run a single cylinder ?.
@j.danaclark89
3 жыл бұрын
Is it possible to get a connector for an external map sensor? Chrysler, back in their early days of efi, found in cold climates condensation would freeze in the internal map and prevent it from reading. When they put it under the hood the problem was solved.
@awb2010br
6 жыл бұрын
The arduino in the your video is only for example purposes? Because don't is a Mega 2560. Thanks for your attention.
@mugeshramanathan3400
7 жыл бұрын
does this work for single cylinder engines??
@Justin-hm4xu
3 жыл бұрын
gday what version board would you recommend to me 0.3 or 0.4 i'm dealing with a 1991 year nissan pulsar that has fuel injection. also where do i get the board gerba file or themselfs do i have to pay or is it open source
@ItsMatich
6 жыл бұрын
Hey Josh, if you installed the extra driver, is it possible to run a 6 cylinder with wasted spark (in pairs) ? - cheers
@awb2010br
6 жыл бұрын
Can I change the MEGA 2560R3 for this ArduinoDue ( very more fast 84mhz in 32bits versus 16mhz 8bits in MEGA 2560)in the vídeo without adapt in the speeduino board or materials????
@Luichiweedy
3 жыл бұрын
Hello friend, a question, the kit of components to solder on the speeduino pcb? Could you provide me with the list? thanks greetings
@ivannavi9278
2 жыл бұрын
Весь интернет перерыл ,не могу найти список компонентов =(((
@DarkLinkAD
7 жыл бұрын
Have you installed this on many vehicles??
@DarkLinkAD
7 жыл бұрын
What about using an Arudino to control an external ESC, which can vary the voltage of a fuel pump with only guidance being a wideband O2 ?? Does this just sound silly?
@hippopotamus86
6 жыл бұрын
It's too much work to get an arudino to control an ESC. That's the idea of a standalone ECU.
@sasaikic6389
7 жыл бұрын
Hello Josh, Big BRAVO for your project? Can I bay board with all these compoments from you for my "TURBO CAR PROYECT" or how I can learn to make circuit plate (board) seems like you? Best Regards Sasa
@dirtbikedude2989
5 жыл бұрын
What is included in the component kit and what else needs to be purchased to make it a complete ecu? I want to build one for my 1.6 Miata instead of buying the pnp
@dirtbikedude2989
5 жыл бұрын
Price and I like to build my own stuff when possible
@dirtbikedude2989
5 жыл бұрын
Do you know when the pnp speeduino is going to be available again?
@SLYDIT
4 жыл бұрын
What temp do you set your iron to?
@mugeshramanathan3400
7 жыл бұрын
can I use a arduino mega ???
@hippopotamus86
6 жыл бұрын
Yes it uses an Arduino MEGA. The speeduino is a large shield that attaches to it.
@Shadowdarknessone
7 жыл бұрын
what the big difference between the megasquirt Ecus and how is the Quality? and how good is it tunable?
@ExtraFungus
7 жыл бұрын
Shadowdarknessone it's a very similar product but because it uses an arduino board, its less soldering and can be cheaper. It uses the same tunerstudio software as megasquirt.
@nickolasalmeida995
7 жыл бұрын
Josh Bishop can run full sequential injection with speeduino?
@ExtraFungus
7 жыл бұрын
Nickolas Almeida up to a 4cl yes, otherwise you have to run semi-sequential or paired.
@thomasmccall1076
7 жыл бұрын
curious 2 know how much are on of these?
@keiostoute9341
3 жыл бұрын
Where can I buy this board
@niiyuux-x6783
3 жыл бұрын
What's the song in 02:00 please i need it
@mjallen0011
7 жыл бұрын
Would you recommend this for a single cylinder or vtwin?
@keiostoute9341
3 жыл бұрын
They have for bikes .from what I see on youtube
@pedrobenavides80
6 жыл бұрын
you could help me with the list of components since I can not get it? thank you very much
@hippopotamus86
6 жыл бұрын
The speeduino.com website has the full list. Also on eBay you can buy the complete kits.
@MrDstoya
6 жыл бұрын
Thanks!
@mygius1
5 жыл бұрын
is there a list of components?
@st5rk
3 жыл бұрын
Did you ever find a list of components? I'm having a hell of a time finding info how to actually build one of these.
@mygius1
3 жыл бұрын
@@st5rk yeah, they are in github. Search in google "speeduino bom". I eventualy managed to assemble it myself mostly using parts from local electronics shops.
@st5rk
3 жыл бұрын
@@mygius1 thanks, found it. What car did you put it on?
@mygius1
3 жыл бұрын
@@st5rk that project is still going :D now it is like 2 years by now. I had useless 89 civic D14A1 engine without car which no one wanted, so i tried to convert from carbs into injection. By now it has coils, crank sensor and ehatever it needs to run, but it is still siting outside not started yed, im lazy to tinker now
@ianfairbanks1318
5 жыл бұрын
thank you, Josh!!! is a kit in the works for the 1.8 miatas yet?
@ianfairbanks1318
5 жыл бұрын
@@Speeduino Is this a "within a year" or a "within a guess" timeframe? i have money, i have time. but not usually both. lol.
@destineal
7 жыл бұрын
Should I be getting a Due, and not a mega?
@hippopotamus86
6 жыл бұрын
You can use a Mega.
@RixtronixLAB
3 жыл бұрын
Nice video, thanks :)
@sicariostar8961
4 жыл бұрын
U are a genius
@networkingdude
8 жыл бұрын
I want to design a new board for this that integrates the atmel on one board.
@hippopotamus86
6 жыл бұрын
You can try, I thought about it, but you need to get them pick and placed, you couldn't really do it by hand very easily.
@michaelkincaid9582
5 жыл бұрын
The ATmega is also available in DIP packaging. But even with the flat pack version, soldering 0.8mm pitch isn't fun,but it can be done... The way i solder, I'd buy 3
@TurboMiniTV
6 жыл бұрын
Good video - the problem I have is you going up^^! at the end of every sentence^^! (Think Stewie griffin) is putting me off.
Пікірлер: 55