@Mattsneedforspeed if we don't have a cat? Where do we install? As far up stream as possible?
@traxxasxmaxx3359
4 жыл бұрын
Matt I'm looking 4 a 2004 srt4 stock intake hose can't find 1 anywhere was wondering if u can help me?its not the little hose that goes 2 the head it's the main hose that I would put the air filter on.
@Mattsneedforspeed
4 жыл бұрын
I don't have one it seams to be a needed part here now i how lots of people looking for them
@traxxasxmaxx3359
4 жыл бұрын
@@Mattsneedforspeed damn alright thanks matt
@Mattsneedforspeed
4 жыл бұрын
Traxxas Xmaxx you will have to pull out the seal carefully and inspect the surfaces and if ok reinstall new seal
@senditdriving2479
Жыл бұрын
Matt… just got a afr gauge.. when installing do you have to connect the wires to the pcm? And on the o2. Since it’s unplugged do you get a code?
@Mattsneedforspeed
Жыл бұрын
nothing on an aftermarket afr gauge gets hooked to the cars ecm, you are adding a sensor. if you are removing the down stream sensor you will get a code and a check engine light. new afr sensors should come with a mounting Weld In Oxygen Sensor 02 Bung this needs to be installed upstream of the catalytic converter to get a correct reading of the air flow ratio. www.ebay.com/itm/165570557243?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ycDuSlRzStW&sssrc=2047675&ssuid=lDFTDWAdS1i&widget_ver=artemis&media=COPY
@Spikerjackjack
Жыл бұрын
Is it normal for it to throw a engine light for o2 sensor cause don’t you replace the o2 with the AFR gauge
@Mattsneedforspeed
Жыл бұрын
if you unplug and remove the down stream sensor yes you will get a check engine light, the after market gauge is separate from the cars ecm. you will need to get a new sensor bung welded in, will need located in front of the catalytic converter here is a link for it if your gauge didn't come with one www.ebay.com/itm/165570557243?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ycDuSlRzStW&sssrc=2047675&ssuid=lDFTDWAdS1i&widget_ver=artemis&media=COPY
@daylenb7014
3 жыл бұрын
So did you just put the gauge pod pillar over the stock A pillar and route the wires through the stock A pillar? I have my gauge pod from glowshift and I just put the gauge pod in place of the stock one not over it. Should I put it over it?
@Mattsneedforspeed
3 жыл бұрын
Most install over the stock pillar cover for strength and because the clips are no there in the pod this one was already assembled when I got it but yes I would suggest you install it over the stock one
@servantofthetruth8203
3 жыл бұрын
Sup matt quick question,where does the vacuum line that's hooked up to the boost gauge go?.. I just had it installed but it's not moving at all..
@Mattsneedforspeed
3 жыл бұрын
It runs threw the harness if you look up under the steering column by the kick panel it connects there then out to the t on the brake booster
@servantofthetruth8203
3 жыл бұрын
@@Mattsneedforspeed thanks man,they have it tapped into the wastegate..is that the only place it would function correctly or can it be tapped into another location and still work?
@edwinaquino9291
4 жыл бұрын
Hey what’s up buddy I have a quick question. I’m looking into getting a srt4 I found one but has the rear main seal leak? How bad can that be? Can I still be reliable or would it be hard to change
@Mattsneedforspeed
4 жыл бұрын
the rear main is just slightly more involved then doing a clutch replacement since you need to remove it to install a new seal.
Пікірлер: 24