Manufacturer: "you said you wanted what again?" Printed Solid, Inc: "the most annoying alarm notification system you have.. you know just to let me know the machine is running properly... all the time." Manufacturer: "ok, but it's going to go off every other 30 seconds"
@UDoIt2
4 жыл бұрын
Amazing David. Thanks for taking the time to create this. Coming from the process control industry it's nice to see how some of the technologies I worked on are utilized.
@highdesertdrew1844
Жыл бұрын
Reminds me of working with cold header machines to make bolts and screws. Except we were feeding the wire in, running it through the straighteners, and then hauling buckets of screws off at the end.
@3ffrige
2 жыл бұрын
Amazing! Takes all that work, machinery and technical know how to keep an entire spool of filament at 1.75mm diameter!
@barrysotero137
Жыл бұрын
No wonder that creepy cheap Amazon filament snaps, crackles and pops…
@ak1facar
7 ай бұрын
Giant team of one, congratulations.
@Jandodev
2 жыл бұрын
the buffer is really cool!
@daviddrummerrichards2724
3 жыл бұрын
I worked on extruded lines with dura cables our extrudes had a scantron which automatically speeds up and slows down if the outside diameter goes out of tolerance
@janmessek1826
4 жыл бұрын
Would it be possible to run out of spec (larger) filament through some heated rollers to reshape the entire roll into spec? Also seems that you could thread the machine with a "string" and then attach it to the beginning extruded filament so you don't have to walk the filament through the entire machine at each startup wasting that first length with time critical threading when you could be adjusting the quality of the extrude during that time. Pretty impressive operation I must say. As for that first roll I would think you could just feed it back into the grinder/hopper at the input?
@wize2140
2 жыл бұрын
Where do you source your dies for cooling trough? Can you explain more about why you need dies etc..
@davidbutcher6637
Ай бұрын
Cool vid what is the pallet grinder you are using or do you buy in pre made coloured stock ?
@josephocharles
Жыл бұрын
Thanks. Nice video
@Mriya6
6 ай бұрын
Very cool. Do you run the waste spools through a pelletizer or shredder so that it can be remelted in the extruder and recycled? It's all totally clean and containment-free after all!
@ugurdincer6381
2 жыл бұрын
Hello, why do you have an ionizer on the winding machine? Does it make filament stronger?
@ziyuanwang5332
Жыл бұрын
Can I get to know where you purchase and assemble this set of machine? And, how much will it cost?
@IlanPerez
2 жыл бұрын
Who knew you needed so many machines to extrude filament. Love to know the cost (about) of the setup. Also why dont you recycle the filament that fell on the floor? is it contaminated?
@randomanimator1336
2 жыл бұрын
I'm pretty sure it would be out of spec and contaminated.
@plasticextrudermachinedesi8342
2 жыл бұрын
Hello, Dear friend ,this is Wendy comes from Nanjing GS-mach Extrusion Equipment Co.Ltd.Which is a professional machinery designer and manufacturer. please contact me if you are interested.Whatsapp/Wechat:+86 18151606635 Email:sales6@njgsmach.com
@ChristopherJones16
2 жыл бұрын
about $30,000.00 paper fiat.
@WhenThoughtsConnect
2 жыл бұрын
cant you just 3d print pellets using the out of spec filament roll?
@ameliabuns4058
2 жыл бұрын
have you tried extruding ultem/peek? those seem to have a lot of profit. a huge difference between the pellet/filament
@royaldecreeforthechurchofm8409
Жыл бұрын
Peek has ip I believe
@lemonvolt
3 жыл бұрын
Wow! What is this filament extruder and where did you get it? It is beautiful.
@plasticextruder66
2 жыл бұрын
Thank you . More information , pls contact with me .
@steveworkers6838
2 жыл бұрын
We can produce filament machine . sales1@mq-extrusion.com
@alexsaha
3 жыл бұрын
awesome video - just wondering how do you shut down the line ? is it shut down every day and start over tomorrow?
@plasticextruder66
3 жыл бұрын
Pls contact with me Ms Candy 008615118427012wechat/whatsApp
@plasticextrudermachinedesi8342
2 жыл бұрын
Hello, Dear friend ,this is Wendy comes from Nanjing GS-mach Extrusion Equipment Co.Ltd.Which is a professional machinery designer and manufacturer. please contact me if you are interested.Whatsapp/Wechat:+86 18151606635 Email:sales6@njgsmach.com
@rcmaniac25
4 жыл бұрын
Is the alarm for "the diameter/ovality is out of spec" or "you are approaching the finger crusher"? Also, what do you do with the trash filament? Like, do/can you recycle it?
@rcmaniac25
4 жыл бұрын
@@printedsolid K. Still waiting to find a good filament recycling place for filament. Between this video and the follow up, I'm assuming there is gonna be someone full time staffing this machine.
@Lordoffail
4 жыл бұрын
@@printedsolid Why can't it be recycled? Every single plastic molding and extrusion process I've worked with has run 10-25% internal recycle material or "regrind." If it's a question of color, black dye covers all sins. If it's a question of Nature Works telling you not to run regrind, they are wrong. We do it all the time without issue. So do most large scale PLA processors. Eitherway, contact me @ howcanwehelp@polymerforge3D.com or poke Max Mcgrumpy on Facebook.
@dansmith5505
3 жыл бұрын
@@Lordoffail Recycled filament works for most people, but if you want the best properties you should never recycle filament. You should always use virgin plastic pellets. The cost savings of using regrinds is negligible on the professional scale. It is better to save them and utilize them for a lower quality run, or even just selling the scraps by weight for someone else like a hobbyist to deal with.
@plasticextrudermachinedesi8342
2 жыл бұрын
@@dansmith5505 we can recyle it ,equip a set of pelletizer , please contact me if you are interested.Whatsapp/Wechat:+86 18151606635 Email:sales6@njgsmach.com
@ajhmakki
3 жыл бұрын
Hello, I have a couple questions. what is the finished size you are producing and what are the sizes of the dies you use to keep the shape?
@plasticextrudermachinedesi8342
2 жыл бұрын
1.75MM-3MM, please contact me if you are interested.Whatsapp/Wechat:+86 18151606635 Email:sales6@njgsmach.com
@BKWParts
2 жыл бұрын
3:33 can you explain more in depth what you are doing here? and what you mean by tensioning the accumulator? How does that work?
@samdyerson9346
Жыл бұрын
We used a system like that to tension wires between a sport fencer's back and the wall at the end of the fencing strip, where the scoring machine was hooked up. It's a block and tackle arrangement where the spring tension pulls the pulleys apart to take up the filament, and then will feed it back out according to the torque on the filament spool. Tensioning is just getting the accumulator spring force in the proper ratio with the take-up spool torsion. It's a pity he didn't continue the video to show a reel being replaced. That would have shown what the accumulator's job was. It would continue to gather product while the spool was being swapped.
@mortezakhedri5915
2 жыл бұрын
Hi. thank you for your video. Can you please tell me why do you cool the Filament with the Water and not with the Air(For Example PC FAN)?
@roccocroce
Жыл бұрын
If Rube Goldberg was a 3D printing nerd. Can I work here lol
@aliev010
2 ай бұрын
Hello, I am producing 3D filament in Azerbaijan, but I am experiencing problems during production. Can you help me?
@marclanglais9812
2 жыл бұрын
Love this. What is the temperature of water? I'm curious to know :)
@plasticextruder66
2 жыл бұрын
The water temperature , it according the raw material ,PLA around 65 degree
@marclanglais9812
2 жыл бұрын
@@plasticextruder66 65°F in the first water bath?
@plasticextruder66
2 жыл бұрын
@@marclanglais9812 Yes
@sam-cj8tf
Жыл бұрын
@@marclanglais9812 I think its celcius, because it needs to be heated. And it think it isnt heated to 65 fahrenheid (or there need to be polarbears inside)
@johanjotun1647
Жыл бұрын
I never imagined it was such a process to make a plastic string
@kabasakalka
2 жыл бұрын
Hello David! I appreciate the work you've done here, thanks. We are setting up a similar business in Turkey and i don't know if you produce ABS but we have problems with the rounding of the ABS. Those tools you use in the water tank for rounding, are they also applicable for ABS? What is it how can we find it? If not too much can we have your e-mail address?
@f7357
2 жыл бұрын
I am an extruder operator and the tools in the water tanks have ONLY one use is to old off water when the tanks fill up . The shape always have to start from the die then to keep the form you have to play with speed , cold pressure air between the die and the water tanks or you can add a die with a vacuum system in the water tanks to keeps the shape
@rexxx927
2 жыл бұрын
ABS and ASA are cooled first with an air table then a water table the dies are a different size if your still in need ?
@egemenpekmezci6298
6 ай бұрын
turkiyeye yaptınız mı
@egemenpekmezci6298
6 ай бұрын
üretime başladınız mı
@jaydawg2357
5 ай бұрын
Thats too much sh_t to worry about for me. But thats still Cool. You are very skilled.
@3dvolk961
Жыл бұрын
David , can u tell me the temperature setups for petg extrusion ?
@plasticextruder66
Жыл бұрын
Melting temp. or water temp. i can let you know
@matthewguthrie6112
Жыл бұрын
How much would an hourly rate be to have someone do this for you
@plasticextruder66
Жыл бұрын
15-20kg per hour
@blackbeton3923
Жыл бұрын
Nice process, no room for laziness though 😅
@jamisoncoal1620
2 жыл бұрын
Where did you source everything from besides the extruder?
@ChristopherJones16
2 жыл бұрын
probably some chinese people when Americans and Europeans should be manufacturing such machines for a 1/3 of the costs ONLY for domestic transactions but instead they jack up the prices on domestic products that leave us with no choice but to buy Globalist's imports since they own shares of China.
@plasticextruder66
Жыл бұрын
kzitem.info/rock/OH5sHzZtI4wiVFjNQaSQCA
@prashant8227
3 жыл бұрын
Very good
@plasticextruder66
2 жыл бұрын
thank you
@wk12blood
4 ай бұрын
How much does a line like this cost today?
@chez1k
28 күн бұрын
20-30k$
@MrDENIS972
3 жыл бұрын
Interested in buying a machine For PLA production what is the process Regarding materials? A 1KG of raw material gives me a 1KG of filament?
@danieljia5452
3 жыл бұрын
On this subject, it is attainable. Interested: Tel: 0086 18151621522 (wechat/whatsapp) Email: sales2@njgsmach.com
@diqianluo7533
3 жыл бұрын
hi,can you add my whatsapp 008618067840591
@plasticextrudermachinedesi8342
2 жыл бұрын
almost,the waste of the raw material is little . please contact me if you are interested.Whatsapp/Wechat:+86 18151606635 Email:sales6@njgsmach.com
@steveworkers6838
2 жыл бұрын
We can produce filament machine . sales1@mq-extrusion.com
@latinourbano
Жыл бұрын
How much does extruder operator make?
@plasticextruder66
Жыл бұрын
1 worker run one production line
@achref5829
2 жыл бұрын
hi sir i'am a mechanical engineering student why do you use 2 long tanks of water for cooling ? why you don't use 1 or air cooling ? and why the distance between them ? please i need your answer for my research
@plasticextruder66
Жыл бұрын
According raw material melting and forming process . some raw material need Air cooling some one need water cooling . to keep producing good tolerance filament
@achref5829
Жыл бұрын
@@plasticextruder66 thanks for your help ❤️
@5kopiyok
5 ай бұрын
2:00 Why having these wheels?
@skaltura
7 ай бұрын
shame it got cut off. That's quite a bit of waste, and quite an line. Seems like running it 24/7 makes more sense than restarting it daily. That is quite a bit of wasted plastics.
@royaldecreeforthechurchofm8409
Жыл бұрын
Why water I thought filament is meant to be dehydrated.
@lego3438
Жыл бұрын
Wow
@Kotaztrafee
3 ай бұрын
I need ASA 🙂
@spdrcr99ta
4 жыл бұрын
Grab the hot plastic with your bare hands like a real extrusion tech = P
@manofgod9843
2 жыл бұрын
ikr I do 350+ degree all day sometimes run high density pe which is upwards 475 degrees
@WhenThoughtsConnect
Жыл бұрын
its nuts because hes calibrating machines that are dependant on other machines lol imagine how much waste that was initially starting it up and fiddling with everything to get the numbers right like how did he figure out the winding speed to not destroy the filament capacitor lol
@@plasticextruder66 how much Kw does the total system use?
@plasticextruder66
Жыл бұрын
@@sam-cj8tf 45kw
@sam-cj8tf
Жыл бұрын
@@plasticextruder66 is 45kw the max power usage or the average power usage?
@jakhongiralimov7481
3 жыл бұрын
more like this videos
@GameOver-ge2hr
2 жыл бұрын
Water ?! 😱
@BikZom
10 ай бұрын
bro i was wondering why my filament is wet
@ameliabuns4058
2 жыл бұрын
wow this process has so much waste! also so much work damn no wonder PLA costs 25$ a KG lol. can't you recycle the first spool or use it in house for non-important projects?
@RemiDupont
2 жыл бұрын
Same question here.
@user-uy7nj9br2i
11 ай бұрын
Dejó dolgoznák ott
@google.belarus
3 жыл бұрын
Я не могу купить такую линию! Очень дорого! Делаю сам, для себя, с меньшими скоростями и не таким контролем всех процессов.
@plasticextruder66
3 жыл бұрын
Machine from our company . pls contact with me
@mywa8314
4 ай бұрын
I guess it never settled in
@MindsMouth
2 жыл бұрын
Just imagine, in China there are children running these machines. Most are more skilled than this guy 😂
Пікірлер: 104