Really enjoy these videos it’s amazing how far technology has come with these tools. Thanks for the post can’t wait to watch one of these videos on ms261 or 661. Thanks for posting
@em4703
2 жыл бұрын
Factory air filter is amazing. The problem is the yellow foam ring at the top of the air filter support. Add another one over it, and not a speck of dust will ever enter the intake.
@cajun3197
2 жыл бұрын
This is great tips!
@otoroot6570
Жыл бұрын
Hey, do we actually need a re-seller login to use the software and the diag tool ? Like the Husky one ?
@richardflagg3084
Жыл бұрын
Husky requires a dealer login. The Stihl may require a little assistance to set up on your computer, but there is a non-dealer login they will set you up with.
@mfsaws8240
Жыл бұрын
I’m combing back through your 500i videos wanted to bounce a question off of you. I’m working on a ported 500i. It does everything it’s supposed to but when he is cutting its like he hits the kill switch. It will just die mid cut. It will fire back up one pull and run fine until it quits again. He said it was once in a while now it’s doing it more frequently. I once overed everything and looks good. Vac pressure tested and everything. My next stop is the dealer to hook up to mgd1 but not sure if my dealer even does anything like that. They arnt the best when it comes to saw knowledge. Any places I could check before I go to dealer with it?
@richardflagg3084
Жыл бұрын
I think you've done everything you can do. Getting it plugged in should reveal whatever is starting to fail. I haven't had one do that yet. I'd appreciate a follow up after the diagnostics. Thanks, Rich.
@mfsaws8240
Жыл бұрын
Yessir you bet I will.
@richardflagg3084
Жыл бұрын
@@mfsaws8240 Much thanks, Sir.
@howardnphyllis
Жыл бұрын
Possibly your coil heating up and shorting? then when it cools, it works again...? I've had that happen on several units in my shop in the past. or maybe insulation has worn away and exposed the copper in the wire to a ground.
@user-xf9lp2pt3q
10 ай бұрын
Бывает катушка зажигания и датчик давления
@2Aces
Жыл бұрын
Does this allow you to recalibrate also?
@richardflagg3084
Жыл бұрын
Yes you can initiate the recalibration while it's plugged in.
@HYPERSAWS7mm
2 жыл бұрын
Hi Richard, is it easy to get the software for that mdg1 tool I am going to get one if I can get the software, thanks
@richardflagg3084
2 жыл бұрын
When you buy the kit it comes with a code to activate the unit. It downloads directly from Stihl. As there are updates to the system you are notified when you open the program. There is only the initial cost of the kit. No annual fees or renewal costs. Its worked flawlessly in the last year or so since I've owned it.
@HYPERSAWS7mm
2 жыл бұрын
@@richardflagg3084 ok thank u very much, I have a dead 500i with all new parts so I am curious what it will tell me
@richardflagg3084
2 жыл бұрын
@@HYPERSAWS7mm I'm positive I couldn't have fixed this 500i without the MDG1. It's got a lot more electronics than the rest of the MTronic line up. I rarely need the MDG for an MTronic saw. When one of the components fails it's pretty obvious and only requires a simple part swap. Keep us posted with your 500i. Thanks, Rich
@HYPERSAWS7mm
2 жыл бұрын
@@richardflagg3084 yep that is exactly what I was thinking as well,
@HYPERSAWS7mm
2 жыл бұрын
@@richardflagg3084 is there a link the kit comes with or do u have e to be a dealer?
@gradycothran3896
2 жыл бұрын
I'm the first. Stay warm rich
@richardflagg3084
2 жыл бұрын
Wood stove is rolling. Gonna be a cold one tonight
Пікірлер: 24