Excellent vid Mr. Richard, +462 oil pump roll-pin...
@cajun3197
Жыл бұрын
Ooof I need to check the elasticity of my case half’s just in case they’re out of spec. Glad you reminded me of that detail. Easily over lookted 😂😂😂😂
@b.butcher82
Жыл бұрын
I'm gonna go buy an 064 tomorrow. Too much bullshit on new saws.
@donmayberryjrsOPE
Жыл бұрын
I know right!? The average guy can't work on them. But then again..... who's average? 👀🤣🤣
@em4703
Жыл бұрын
@@donmayberryjrsOPE If you can't work on this saw, you can't work on any saw properly, sorry. It's not like you got to write lines of code for it or other nerdy stuff, it's still the same things that fail like any carbureted saw. You still got a diaphragm fuel pump, you still got seals, crank, piston, sparkplugs etc. The injector can be refurbished by changing 2 parts in it (if it ever needs it). I never saw electronics ever failing on a 500i, nor on the injection concrete saw they also sell for over a decade now. And that thing sees dust and water continuously, yet the electronic board keeps going.
@richardflagg3084
Жыл бұрын
064's make good wheel chocks too....
@b.butcher82
Жыл бұрын
@@richardflagg3084 I hope I never have to find out. Hahahaha
@aaronpowell4885
Жыл бұрын
Twas definitely in the hands of a smooth operator😎 Guess I don't use my saws enough, as I haven't yet experienced floppy case syndrome👀😅 Thanks for sharing your job security👍🏻
@oldcodger1929
Жыл бұрын
I'd hand that dude a hand saw until he learns how to operate a chainsaw. Enjoy your day sir.
@jerseyjoshua4818
Жыл бұрын
Rich has that Fired🔥Up Friday jokes... absolutely totally normal maintenance after the saw meets a wheel.
@tobysmith8032
Жыл бұрын
Good tip on the seal installation, I have been using this method for years, works every time! 👍
@thomasgronek6469
Жыл бұрын
Wow, such a magnanimous gesture by Stihl (bar studs, and bearing)
@em4703
Жыл бұрын
Some people should be using only the tools that the Swartzentruber Amish do. But I think even a hammer and a pull handsaw wouldn't be safe in the hands of people like this fella..
@richardflagg3084
Жыл бұрын
Accidents happen but some people could break an anvil with a feather.
@dwusuwowy
Жыл бұрын
Very nice saw stand!
@richardflagg3084
Жыл бұрын
Scott Kunz "treemonkey" made it. Dunno if he's still making them, but it's worth every penny
@harryerhart5978
Жыл бұрын
Thank God l don't have employees l would be in jail now 😜
@sawmanbigtreeslayer2360
Жыл бұрын
My guess this pro operator gets this saw stuck in wood and then pulls real hard on the tank handle to free it.
@gradycothran3896
Жыл бұрын
Rich you must have the same tree guys that I do. It just needs a spark plug
@richardflagg3084
Жыл бұрын
Damn near.
@em4703
Жыл бұрын
@@richardflagg3084 5:34 you forgot the airfilter foam bushing/seal :P You'd better have put it in there later, if not I doubt this gentleman that owns it would ever check and just run it until dust kills it.
@richardflagg3084
Жыл бұрын
@@em4703 Good eye! Thanks
@VintageEngineRepairs
Жыл бұрын
Great video 😂
@richardflagg3084
Жыл бұрын
"Yes"
@perkypat2214
6 ай бұрын
Hi Richard, nice video. Is all of this damage a reflection of the poor quality of the saw or the poor behaviour of the user?
@sawmanbigtreeslayer2360
Жыл бұрын
A wheel chock? 😂🤣😂🤣
@kenweis7913
Жыл бұрын
Sorry but you can keep the 500I to complicated to many things to break
@giuseppelatina2640
Жыл бұрын
Hi Rich one of your subscribers here in Melbourne Australia what actually happened to this saw? Thanks Regards.
@richardflagg3084
Жыл бұрын
Backed over. Could have been worse. Thankfully the fuel tank survived.
@darrellpeak2914
Жыл бұрын
Just how much is the boss man’s bill for all this “regular maintenance”?? 😂😂
@richardflagg3084
Жыл бұрын
Parts bill was a tick over $600. Took care of him on the labor to make it work.
@darrellpeak2914
Жыл бұрын
@@richardflagg3084 Holy crap, he’d have been 2/3 of the way to a new one!
@kojirohyuga1050
Жыл бұрын
Should be good for another 27 hours of work. ;)
@darrenfrost5775
11 ай бұрын
just quick question on this rebuild , with the new crankcase you get hardware , new bolts , seal , plus little plastic part , did you find out where this goes , as i am in process of rebuilding a 500i , but cannot see where this part goes , it never fell out the old case when i separated them , so am at a lose ,
@sawmanbigtreeslayer2360
Жыл бұрын
What is the experience level of the person that owns this gem?
@jimssawsnstuff8903
Жыл бұрын
He said the crew used it for a wheel chalk, meaning it got run over
@sawmanbigtreeslayer2360
Жыл бұрын
@@jimssawsnstuff8903 I got that at the very end. Thanks
@johnclarke6647
Жыл бұрын
Richard, do you have an old intake boot band? My new Farmertec ms 250 kit saw did not come with one. The seals that came with the kit, sucked. I put seals in it from Stihl and they worked fine. They even had dust covers, which did not come with the Farmertec seals. Those Farmertec seals were so brittle they disintegrated when I tried to put them on the crank shaft.
@mikeydesilva8197
8 ай бұрын
27 happy hours 😍😀😛
@meatpie1380
Жыл бұрын
I got my schaffers oil in today
@scottsmith8056
Жыл бұрын
Glad that wasn't my fault!
@Mike_Mike_0
Жыл бұрын
Nice video and very informative. What does one have to do to break a case in half? Drop it from a heli?
@richardflagg3084
Жыл бұрын
🤣🤣 Actually that part of the case is really thin. It took a pretty good lick tho
@richevy5224
Жыл бұрын
What did the piston look like Rich? Was there damage from the broken injector pump?
@richardflagg3084
Жыл бұрын
Piston was lightly scored. It would still run. I don't know how or when it got scored. The injector pump housing was cracked where the fuel lines plug in. The metal bracket that holds it in place was bent in. I'll do all the MDG1 diagnostic tests and run it tomorrow. I didn't see any damage around the injector itself. we shall see
@richevy5224
Жыл бұрын
@@richardflagg3084 Cool. Thank you.
@mrxlh
Жыл бұрын
Stihl? Nah….Aluminium….
@austindenotter19
Жыл бұрын
I guess you can keep your 27 saw. not worth the pain in the neck. Unless it wasnt the saws fault.😁
@sawmanbigtreeslayer2360
Жыл бұрын
Funniest video you ever made!!
@NiallFC
Ай бұрын
Thats Funny.
@kenweis7913
Жыл бұрын
Just buy a new saw
@madmike8869
Жыл бұрын
It's stihl a pile of crap, and the air filtration system stihl isn't better than husqvarna lol
Пікірлер: 52