Hi, does the carby need to come out when your replacing the new piston and rings, cheers.
@김현균-l7c
3 жыл бұрын
Thank you. Very helpful for me.
@NelsonGallo1
2 жыл бұрын
Can you explain the adjustments you did a the end? With the screwdriver. Thanks
@TheDingdong78
2 жыл бұрын
you need the tuning screwdriver for it
@NelsonGallo1
2 жыл бұрын
But what did you screw in ? I noticed there are 3 small screws which one I need to adjust and what do they mean ?
@backdraftdragon3150
2 жыл бұрын
I have the same problem,when I put the filters on it won't throttle up. Any ideas what the problem coul be? I've replaced the carburetor
@brianburroughs5378
3 жыл бұрын
COOl BRO you the best
@jeremyfoskett4482
11 ай бұрын
Where did you order your parts?
@brianburroughs5378
3 жыл бұрын
Can you you teach me how to rebuild a zero turn transmission step by step please
@chrisherald4303
Жыл бұрын
Hey bro What kind of oil for the crank?
@TheDingdong78
Жыл бұрын
Use Paslode oil .
@jensvandendooren8899
2 жыл бұрын
hi, i have the exact same problem when i put airfilter on, it does not run properly. how did you solve that problem?
@TheDingdong78
2 жыл бұрын
checked compressure.it it under 120 psi replace new piston essamply...
@jensvandendooren8899
2 жыл бұрын
i already changed cylinder and piston+rings, crankshaftbearings and seals+new spark plug(bpmr7a ngk). i also put new membrane in old carb. i do not understand it anymore, only thing i think is changing the carb but here in Belgium it is very expensive....
@TheDingdong78
2 жыл бұрын
@@jensvandendooren8899 can you buy sevice kits
@TheDingdong78
2 жыл бұрын
open up the carbi...change the diaframe black piese like the thin air drum..and all the part come in the kit..did you try turn and tune the carbi?
@jensvandendooren8899
2 жыл бұрын
@@TheDingdong78 yes, already changed diaphragma in carb, and cleaned as good as possible the rest of the carb. No succes with adjusting the carb also......
@TheDingdong78
2 жыл бұрын
yes
@backdraftdragon3150
2 жыл бұрын
Hey Simon, did you ever find out why the ts800 didn't power up with the filters on. I put a new carburetor and I have compression. I'm at a complete loss of what to do . Any advice would be great plus I adjusted the screws and it still boggs down. Thanks. Russ.
@mightykyu
Жыл бұрын
Hi. I bought 1 used ts800 but I cant pull the cord to start. Its very hard. After pushing decompression switch, can pull once but no start then it becomes very hard again. Any idea what the problem could be? I removed the spark plug and then the cord becomes free. Puzzled. Thanks
@TheDingdong78
Жыл бұрын
Checked comprressure over 100 psi is good.when cold start pump X5 times and choke on .pull until you hear it run once it will.stop traight the way..put the choke back normal..use your feet open the throttle full open and pull fast until it start...this is best to start all the still 2 stroke tools
Пікірлер: 29