that is a neat little engine. I think paint it, it should look like the gem that it is. be proud man great job
@jbslittleshop2897
Жыл бұрын
Thanks for stopping by and checking it out sir. 👍
@firstrespondergarage
Жыл бұрын
You make we want to get that 413 in the shop and start mocking up the blower on the intake. Awesome progress 👍👍 Id paint it. Break out the map gas torch and rusty metal primer. Then paint it, BUT leave the blower the was it is with the center flat black. Black actually gives off more heat.
@jbslittleshop2897
Жыл бұрын
It’s getting painted. But I am moving forward sir. Hoping for the best. 👍👍👊
@christopherbates6806
7 ай бұрын
I need one for my 86 Buick century 2.8
@BareRoseGarage
Жыл бұрын
Looking good guys. As for paint and shine....... I say heck yeah! Nothing like pulling up in a ratty looking truck or car but when you pop the hood it's that "Pulp Fiction" brief case moment.
@craytum6945
Жыл бұрын
Excellent. Can't wait to see more. Glad I found your channel. Have a 93 S-10 5 speed and trying to determine if I go with a blower or yank it out and drop in a 302. Thanks from Western North Carolina 😊😊😊
@jbslittleshop2897
Жыл бұрын
Thanks for the comment!! This project is on hold at the moment while I get my 85 blazer back on the road👍👍
@louisbabycos106
5 ай бұрын
Prediction 180 to 220 HP
@mcqueenfanman
Жыл бұрын
When I used to mess around with those I advanced/retarded the cam timing at the cam sprocket. I used a sbc kit that drill out all the holes in the cam gear and install the offset bushing on the pin. Even used the sbc lock plate.
@craytum6945
Жыл бұрын
Sweet little 2.8. Yes chevy red would look nice. So how was the outcome on the rebuild with the blower? How much HP and torque gained? Were you happy with all your efforts? If so...would love to have some specs,cuz I have contemplated do same with mine. Either a blower or a small block drop in. Thanks man to the entire crew for getting these vids for everyone.
@jbslittleshop2897
Жыл бұрын
Happy with it so far. Still working on the truck. It’s almost ready to drive. Then I how much gains.
@DJTruth_1970
9 ай бұрын
Lookin good JB…
@directconnection6661
Жыл бұрын
I definitely want to see the end result of this
@torqueracingproduction
Жыл бұрын
I like a nice 25% underdrive pully / balancer myself
@jbslittleshop2897
Жыл бұрын
This is my first time playing with a blower. Just letting a few people give me some guidance on how to get it done. She will be a little screamer!!!!
@torqueracingproduction
Жыл бұрын
@@jbslittleshop2897 I don't doubt that it'll be fun!
@musclecarmitch908
Жыл бұрын
That's one cool little engine! I'd paint it Chevy orange and leave the blower natural aluminum!👍
@jbslittleshop2897
Жыл бұрын
Thank you sir. Still playing around. Got a way to go.
@louisbabycos106
5 ай бұрын
Paint the blower the same as in a 3800 SC application. Paint the engine red .
@christopherpoucher483
9 ай бұрын
A chevy cobalt supercharger should be good, 3800 sc would probably be really powerful if running a chemical cooler for the boost
@RedEyedPatriot
Жыл бұрын
JB I'm dyin to build a 4200 vortec inline6 and drop it in a little s10 or chevy luv or maybe a 2dr Chevette.
@jbslittleshop2897
Жыл бұрын
That would be wicked as hell!!!
@lollipop84858
Ай бұрын
From hell? Can you explain the from hell part of the statement please?
@jbslittleshop2897
29 күн бұрын
@@lollipop84858 well sir. If you watch all the videos it becomes self explanatory!!👍
@Lars615
Жыл бұрын
🤘😎🤘😎
@RedEyedPatriot
Жыл бұрын
😎🤟
@christophertrotter4831
3 ай бұрын
Really interested in that supercharger!! Any info you could provide would be greatly appreciated!!
@jbslittleshop2897
3 ай бұрын
It puts out 5 pounds of boost at 5000 rpm’s and the company that made them are no longer in business. I bought it from a guy on facebook
@donnysouthwell8104
Жыл бұрын
I have a 2.8 chevy v6 im going to rebuild and modify because its going into my 1972 vauxhall firenza
@joshuaknudsen8339
Жыл бұрын
This is exactly what I want to do with my truck idk if this is the same engine as my truck but if you can answer that for me I would really appreciate it I have a 1993 Chevy s10 2.8l manual is that the same engine as yours thanks ima watch your video now
@chevypower1993
Жыл бұрын
Curious as to what total cost is for the build. Got a 93 2.8 5 speed and contemplating a small block swap. Must say that this looks interesting if the end result produces enough hp.
@jbslittleshop2897
Жыл бұрын
This engine was built a while back. I believe the engine and headers were around 3500.00 the supercharger was 900 used.
@Tibiansgarage
5 ай бұрын
Where did you find a blower for a 2.8? I can’t find any
@jbslittleshop2897
5 ай бұрын
I bought it from a guy in a S10 forum a few years ago.
@robertmcbeth5864
Жыл бұрын
Had a friend that had a lil supercharged 2.8
@jbslittleshop2897
Жыл бұрын
Did it run pretty good?
@robertmcbeth5864
Жыл бұрын
@@jbslittleshop2897 it ran very well for a lil 2.8, if I remember correctly it was a lil weiand supercharger and went high 14 sec 1/4 mile on pump gas and not a lot of boost in a s10 blazer, high school days, 2004-2005 ish Side note it was one of the last engines Paul Vanderley did any machine work on, We’re talking about a man whose engines competed from top fuel to Earnhardt’s Daytona winners, local coast legend
@jbslittleshop2897
Жыл бұрын
@@robertmcbeth5864 I’m hoping this thing hits at least 10s in the 1/8. It is 30 over with over sized valves and a big rowdy cam. So 🤞🤞
@michaelkellyjohnson124
Жыл бұрын
what intake manifold and supercharger did you use
@jbslittleshop2897
Жыл бұрын
I bought it from someone. The supercharger is a fogel if I remember right.
@lollipop84858
Ай бұрын
Why all the exasperated sighing? Dont like your job..?
@jbslittleshop2897
29 күн бұрын
@@lollipop84858 i appreciate you worrying about that. Is called asthma. It hits hard sometimes!!😂😂👍
@calvincrews3885
10 ай бұрын
Why not build a 2.8 liter V6 engine they need some luv and some extra horsepower so it can run with the 3.8 and 4.3 liter V6 engines too
@jbslittleshop2897
10 ай бұрын
I got to dust a 3.8 at the race!! Also a few 383’s 👍👍
@Kayla-zq9po
8 ай бұрын
Where do you get a blower for 2.8
@jbslittleshop2897
8 ай бұрын
I got it on a Facebook forum. It was there and I bought it. 👍
@Kayla-zq9po
7 ай бұрын
Thank you 👍
@joshuaknudsen8339
Жыл бұрын
I have a few questions where do I get the blower and why did you set the timing back I don’t know much but I know to know how to do it myself
@jbslittleshop2897
Жыл бұрын
The blowers I have are not made any longer. As for the timing it was a suggestion from a friend that runs a blower. He said it would run better if I retarded it 2 deg. So far it runs great. Hope to drive it soon.
@joshuaknudsen8339
Жыл бұрын
@@jbslittleshop2897 I haven’t gotten to your newer videos just the ones where your building it
@jbslittleshop2897
Жыл бұрын
@@joshuaknudsen8339 I’m close to driving it now. Just finishing some small crap!!
@joshuaknudsen8339
Жыл бұрын
@@jbslittleshop2897 don’t tell me thattt ima still 6 months awayyyyy Spoilerssss
@theclark1814
Жыл бұрын
Do you have any info on this supercharger? Just picked one up but having trouble finding anything on it.
@jbslittleshop2897
Жыл бұрын
FageolSuperchargers.com there is some info there but I think they no longer exist. At least could never get in contact with anyone there. Hope that helps.
@jbslittleshop2897
Жыл бұрын
Also, if you have anymore questions feel free to ask. I have researched that blower for a while. There are a few things I found out. Just please subscribe and like. I will help all I can. 👍
@theclark1814
Жыл бұрын
I called but got no answer as well. See how an email goes
@jbslittleshop2897
Жыл бұрын
@@theclark1814 you will get an email back that says call and they will help. I have been doing that for a while. Like I said. I think they are no longer in business. But I will help you along the best I can. 👍👋
@jbslittleshop2897
Жыл бұрын
I have been trying my best to find out what size blower I have. They make 3 sizes. Your guess is the same as mine. I can give you the numbers off mine. Maybe they are different?! Who knows.
@oldmanintheshopbuiltnotbou8726
Жыл бұрын
paint her chevy orange
@jbslittleshop2897
Жыл бұрын
May go that way. Was just thinking something a little different. But it will probably go that way. Lars hates yellow. 😂😂
@ethanol-fb
Жыл бұрын
if you can find a roller cam for it the regular sbc roller lifters fit and i think the rocker arms are the same
Пікірлер: 73