Hate every car that these went in, but BRILLIANT engines that have a cool sound.
@eatshit8907
9 ай бұрын
You hate fbodys?
@andrewerickson6690
2 ай бұрын
Smoothe rev
@bobg3034
2 жыл бұрын
I love the 2.8-3.1 engine family. Very underrated!
@Saintbow
3 жыл бұрын
My man just gave me a reason to keep my spare old 2.8!
@JesusSaves86AB
4 жыл бұрын
I had so much casting flash on my intake manifold, had to sand smooth as far as I could reach by hand, did the plenum too. Would have ported but I'd rather top swap first. A.R.E. (American racing engines) also makes custom cams and even stroker kits for the 60°s. Looking forward to seeing the progress.
@billbraski2175
2 жыл бұрын
Z24 3.1 ans 2.8s were pretty impressive little cars I remember them beating supercharged 3.8ls
@ronskopitz2360
3 жыл бұрын
Thanks for this! Especially about running the bigger cams with a computer. Am working on “stroking” an iron 2.8 up to 3.1, and plan on running the larger Comp Cams setup. Finding it very difficult to locate programming options for these older TBI engines, but you’re giving me hope that I’ll see some improvement without for now while I research options.
@josephfuenty7253
3 жыл бұрын
The GM 3.1 has a lot of potential for performance upgrades believe it or not my 90 Grand Prix after a full top half rebuild with all performance and bored 60 over with a stroker kit no turbo yet I'm pushing a little under 500hp. Wasn't cheap but very well worth it. If anyone has a 3.1 plenum that says intercooled turbo on it the original one that came with the 3.1 I would pay good money for it to be delivered
@arlenewolf5260
4 жыл бұрын
Is it possible to add 50+ actual streetable HP on the 2.8 with double roller timing chain, headers, up graded distributer, towing and RV CAM, flow bench the head (port match intake and exhaust ports, equlize valve stem heights, largest valves that will fit, 3 angle valve job, roller tip rockers new valve springs etc...)? Do they make a hydrolic roller cam for the 2.8? If the 2.8 can be made to run normally I would be willing to give it a try. Sounds like a $3-4K project.
@modeverything1
4 жыл бұрын
2.8 iron head? Or 2.8 aluminum head Gen II? Its possible, but you will probably need more cam than an RV spec.
@thesovietvorona1007
Жыл бұрын
I just picked up an 89’ 2.7 Z24 Cavalier I’d love to mod at least a bit to get even a bit more than 135. As my old Fiero made 149 from what’s essentially the same engine.
@modeverything1
Жыл бұрын
You will gain a little with better flowing exhaust and cold air intake... but most gains will come from internal upgrades like cylinder heads and a camshaft.
@thesovietvorona1007
Жыл бұрын
@@modeverything1 fair enough
@modeverything1
Жыл бұрын
Just changing the muffler and porting the plenum made a good difference on my old 2.8 RS Cavalier. Would have been pretty quick if I ported the heads!
@petekalemon5594
4 жыл бұрын
My 3.1 v6 in a 1992 Pontiac Grand Prix will run until it gets to operating temp and then spider misfire and stall out. Then it will not start for a while. I changed plugs n wires and camshaft position sensor and a coil pack but still same problem. Any ideas? I’m ready to sell the car because I’m so tired of nothing working.. some say a vacuum leak which could be but I don’t have equipment to figure it out.
@modeverything1
4 жыл бұрын
Sounds like a problem I had with one of my old Cavaliers, would work fine until it was up to operating temperature the start back firing/missing and would not start if you shut it off for at least 15-20mins... turned out to be a bad coolant temperature sensor, it would short out when up to temp, and read -40 on the scanner. Next time it won't start, try unplugging the coolant temperature sensor, and see if it will start for you! Or just put in a new sensor to rule it out, I don't think that they are too expensive!
@KnuckleHeadGarage27
4 жыл бұрын
Anything to know about on the 2.8s and 3.1s I just bought a 87 celebrity eurosport 2.8 and got it running&driving after 7 years it's all on my channel but it needs a timing chain kit bad cause it hits the cover u can hear the slack in it lol . She has like 235,000 miles . I also need to chnage trans fluid cause it slides into 2nd so that's not good
@modeverything1
4 жыл бұрын
Wow, surprised it didn't jump if its hitting the cover! You should be able to use the LZ9 3900 timing chain tensioner on it if you wanted... I will have to check out your videos!
@ethanderryberry9380
4 жыл бұрын
I watch both of you guys’ videos, good shit
@KnuckleHeadGarage27
4 жыл бұрын
@@modeverything1 I bought a 89 celebrity but this one has the 2.54cyl 3speed auto an has 255,000 miles lol an trans kinda slips when gets hot and especially in hot summer days in alot stop and go traffic , car is also on my channel . not sure what im planned to do with the car yet
@Kimani1k_
3 жыл бұрын
I have a 05 Buick century & I was wondering what could I do personally to make my car faster ? With 3.1L v6
@modeverything1
3 жыл бұрын
Throttle body upgrade is probably the simplest to do, or you can do the 65mm like I did in another video. Upgrade the exhaust to a 2.25" or 2.5" free flowing setup. Headers are great if you can still find them, and have someone with HP tuners do a custom tune on the pcm. Other than that your looking at porting and polishing, cam upgrade and turbocharging!
@Kimani1k_
3 жыл бұрын
@@modeverything1 preciate it 😎
@alexhamer7827
3 жыл бұрын
@@modeverything1 I too have a Century mine is an 88 though, what cam would I put in it and what turbos can I put on it, either model years I can salvage parts from or links to places that sell them would be appreciated!
@cesardelgado-pq8dg
3 жыл бұрын
Question: I'm not a racing fan but I have a 86 pontiac fiero stock but I want to stay with the same engine what can I do to it to improve hp
@modeverything1
3 жыл бұрын
There is lots that you can do! I would start by making sure the tune up stuff is all good, spark plugs/wires, fuel filter... then look into higher flowing exhaust and air filter. After that you're moving into the engine with upgraded camshaft, cylinder heads, intake manifolds, throttle body... After all of that you will want to look into getting the PCM recalibrated for the improvements. Even if you just do exhaust and air filter a performance chip/ecm recalibration would help!
@day8799
2 жыл бұрын
@@modeverything1 how much power could it take with it all said and done? I also have a 2.8 V6 surprising I know
@modeverything1
2 жыл бұрын
N/A with cam, ported iron heads, headers and throttle body upgrade you could probably get around 200 crank hp without going too crazy. If you went turbo you would be 240hp+. If you wanted to swap to 31/3400 heads and intakes you would pick up at least 25hp from the start before doing anything else!
@JohnJackson-re4wo
2 жыл бұрын
@@modeverything1 I got a 1986 Pontiac Firebird with the 2.8 mpfi how much horsepower or faster I can make her run
@arlenewolf5260
4 жыл бұрын
I have a 1987 S10 Blazer 4X4 2.8 auto. I think 135HP 135TQ. 62K actual senior citizen garage kept Miles. It was an estate sale vehicle. Runs like new, BUT It is slower than a riding mower. How much HP can you get out of it? and would you do the work for me (I will pay for your time).
@modeverything1
4 жыл бұрын
All depends on how much money you want to spend and how much power you want. You can get more power from the iron head 2.8 like you have but for same money you can swap to a 3400/3500 and have more power! Unfortunately I have too many projects on the go for this year to keep me busy lol
@arlenewolf5260
4 жыл бұрын
@@modeverything1 I have been told the 3.4 is as close to a drop in as you can get. I was also told there are popular hationwide builders that will do some mods (cam and head work) as part of the order for the motor. If I can source a built remanufactured 3.4 would you do the swap.
@modeverything1
4 жыл бұрын
All depends on where you are located and if you can wait until next spring/summer...
@hillbillieslive69
3 жыл бұрын
I have a 91 Lumina with a 3100 can I use the heads and intake off of a 3400 or 3800 all the stuff is very easy to get cuz of my friends wrecker yard I can also use the throttle body off of the 34 38 right but not with the 3100 intake and to change the intake I have to change the heads am I correct. Does it make more sense to buy all new bigger injectors or just go pull used injectors out of a 3400
@modeverything1
3 жыл бұрын
91 should be the gen II 3.1l. 1994 is when they started getting the 3100's. I put a complete 3400 in my old 1992 Lumina it worked great! Yes you can use 3400 heads/intakes on your 3.1 but you will need more than just the heads/intakes. You will need a throttle cable from a 3100 lumina/Grand Prix/Monte Carlo, 3 wire coolant temp sensor from a 2.2L cavalier iirc, egr you will have to make an adapter or try to wire up the newer style, if you have a 3spd trans you will have to rig up a tv/kick down mount on the throttle body. Check out this video to see what I did on mine kzitem.info/news/bejne/2neHmolojaWXiYI This was with the 3500 but its only a few differences from the 3400!
@hillbillieslive69
3 жыл бұрын
@@modeverything1 sounds good this 3.1 had low miles it was already swapped 10 years ago or so and hasn't been on the road a lot. Been a pain with the full tank and struts but this is the 3 time i droped it so i made sure it was good lol. Got to snag what i can from my buddys hes scrap stuff and there is another Lumina ive been parten. Ill let you know how it goes mainly just trying to get the 3400 throttle body and injectors and take the other 3.1 intake and modify it dont wnat to tear into the heads if nothing is wrong at the moment.
@hillbillieslive69
3 жыл бұрын
But if i can get heads i will. And 99 or older?
@modeverything1
3 жыл бұрын
The better castings are 2000+ 3100/3400's. On another note you will need custom pushrods if using 3400 heads on a 3.1
@1flynlow
2 жыл бұрын
i can't imagine paying all that money for extrude honing and then still having to touch em up by hand. i was expecting a lot nicer results from the extrude honing but you can still see casting lines and everything.
@modeverything1
2 жыл бұрын
They looked awesome in 2002-2003 when I first saw them, but I was just getting into performance on these engines. I believe they probably could have done another pass through with the abrasive, but I don't think its cheap, and I don't think it would have done much better.
@hillbillieslive69
3 жыл бұрын
I also have a performance chip on my 91
@zech5054
Ай бұрын
link for where you got it?
@JuyBaba
4 жыл бұрын
I have a 3100 in a Chevy Malibu, what can I do to be improving it
@modeverything1
4 жыл бұрын
Depends on the year of the engine, but pretty much all the same things you can do on a 3400 in a Grand Am or Alero. PCM tuning helps alot, headers, exhaust, Throttle Body (56mm or 65mm). Then from there you can get into the engine with porting heads/intakes, and installing a performance camshaft!
@JuyBaba
4 жыл бұрын
Mod Everything engine year is 2003, been doing a lot of research for my 2003 Chevy Malibu, I’m not sure what pcm tunes to get and headers are quite hard to find especially for the tight fits
@JesusSaves86AB
4 жыл бұрын
@@JuyBaba Go to the junkyard and try to pull the top end off of a similar year 3100 to get a feel for it. Then start porting to get a feel for it. Etc
@Yofatahhhmomma
4 жыл бұрын
@@modeverything1 what's pcm tuning could I contact you somewhere n learn about this 😅 I really wanna make extra hp out of that motor 😂
@davidcovan607
4 жыл бұрын
I'm goin to junk yard tomorrow what year for valve springs and valves themselves
@modeverything1
4 жыл бұрын
Springs are the same from 1994/5 and up 3100/3400. Also the same on the non vvt 3500 (LX9) as for the valves 3500 LX9's are the best "drop-in" OEM but the valve seats will need to be cut to match the larger intake valves!
@charlesballiett6800
4 жыл бұрын
When r u going back to the twin turbo 260 oldsmobile, when is the next video
@modeverything1
4 жыл бұрын
Next video won't be for a few more weeks, just got back to work so I should be able to weld up the gas tank soon!
@strange_waverly
Ай бұрын
I have a 1991 Isuzu trooper with a 2.8l v6. It’s slow going up hills. I need some help
@modeverything1
23 күн бұрын
Is it still stock? A camshaft upgrade would probably be what I would do.
@strange_waverly
19 күн бұрын
@@modeverything1 I’m trying to find. 3.4 to go in it otherwise I believe a cam will do it
@modeverything1
9 күн бұрын
I only suggested the cam in case you were not interested in an engine swap. A 3.4 with a cam would be even better!
@strange_waverly
9 күн бұрын
@@modeverything1 I know it lol I didn’t think about the 3.4 until after. If I can’t find one for a reasonable price I’ma cam the 2.8 and put it back in until I can. I’ve been watching a lot of your vids and I’m m becoming inspired to build a 3.4 for sure.
@modeverything1
8 күн бұрын
@strange_waverly you could always get a 3.1/3.4/3100/3400 crank and 3.1 rwd pistons to put in the 2.8 block. That would at least give you some more torque
@kingsirraps557
2 жыл бұрын
I have a caddy 2.8l 2007 and I want atleast 300whp or 400whp Wht should I do
@modeverything1
2 жыл бұрын
Turbo or supercharger would be the easiest way to get there! I don't know too much about those engines to give you an exact parts list.
@micahbeaulieu4347
3 жыл бұрын
Hey hey I'm actually building a 90 cavalier z24 but I'll be doing a turbo add on u got any extra parts for.3.1
@modeverything1
3 жыл бұрын
What kind of parts are you looking for? I have some stuff kicking around lol send me an email modeverything1@gmail.com
@teammattchew4657
2 жыл бұрын
Any fitment advice/ part selection for 02 3100 in a Malibu? I’m looking to turbo eventually if that’s possible
@modeverything1
2 жыл бұрын
If I was going to do a budget set up for 300-350hp I would use a Ebay/Amazon gt3582 turbo, late 90s 3100 w-body exhaust manifold with a custom crossover or 2 front 3500 g6/Malibu manifolds. Then you would need larger injectors, pcm tuning and a intercooler! *little more involved than that but it gives you a start!
@teammattchew4657
2 жыл бұрын
@@modeverything1 thanks for the nod in the right direction man 👍 time to hit the scrapyards. Anything else helpful I could rip from one of those g6s? Asking cause I’ve seen about a dozen or two of them in town at parts yards and I do need an ac compressor😅
@Bobthedestroyer1990
2 жыл бұрын
Is it possible to put 3100 or 3400 heads on a 3.1?
@modeverything1
2 жыл бұрын
Yes it is but requires a few things to be done in the swap like custom length push rods. I will be putting together a video explaining this swap soon!
@Black.dynamite-
3 жыл бұрын
Would the 3.5 mate up to a 5speed manual? I have a 91 S10 it's a 2.8 2wd and it threw a rod thought about a 4.3 thought about a 305-350 but everyone does that haha
@modeverything1
3 жыл бұрын
Yes it will bolt up but will need custom mounts, and some other work. There is a great write up on thirdgen.org for swapping a 3500 into a firebird/Camaro/RWD it should help lots! www.thirdgen.org/forums/v6/719344-3500-swap-how.html The 3.5/3.9 LZ4/LZ9 can be done too but require a bit more work due to the vvt.
@BeingMe23
3 жыл бұрын
I had a 82 S10 wanted to install a Supercharger 3.8 Buick motor in it. The Gen II had 260 hp.
@christopheryanoski6899
2 жыл бұрын
Can some of these mods be done to a FWD HO Carbie ??
@modeverything1
2 жыл бұрын
The only thing you would be able to do on an iron head carb setup is use the better exhaust manifolds. Its been a long time since I have looked at the iron head stuff... but you may have to elongate a couple of holes on the manifolds to get them to line up correctly. You can do some porting on the heads but even after porting they are only slightly better than a stock 2.8/3.1 head.
@christopheryanoski6899
2 жыл бұрын
@@modeverything1 would there be anything that could be done with the intake on the carbie ??
@modeverything1
2 жыл бұрын
Think Edelbrock made an Intake manifold for them years ago, but they are getting hard to find now. IIRC it was setup to run a small 4bbl carb!
@christopheryanoski6899
2 жыл бұрын
@@modeverything1 it would be nice to wake the old H.O. up. 130 HP ain't enough. Lol.
@justinsantarsiero3971
3 жыл бұрын
I have a 95 buick century special wagon with the 3.1. is there and upgrade for the transmission? Will other trans bolt in?
@modeverything1
3 жыл бұрын
What transmission do you have now? 3spd or 4spd? I'm not to too sure on what is a direct bolt in but you could upgrade to a 4t65e or a 4t65e-HD if you are planning over 300hp!
@justinsantarsiero3971
3 жыл бұрын
@@modeverything1 not positive. But I believe it's the th125. Numbers on the the top of the bell housing are 739. Just looking to be able to tow my boat and trailer. Not sure on the weight of that until I get to the scrap yard. 18ft fiberglass center console. Dual axle homemade trailer. I can pick the tongue up with a bit of effort.
@modeverything1
3 жыл бұрын
I would put a good size external cooler on it and try it. The 3t40 in my old lumina took a beating almost daily behind a 3500, and I loaded It up with parts for swap meets several times!
@justinsantarsiero3971
3 жыл бұрын
@@modeverything1 ok. I'll get it to the scale first. If it's under 2000 lbs I'll give it a try. Just not sure on strength of the transaxle. I just bought it. The car only has 105,000 on it and I just put a Cutlass engine into in with 98,000 miles. So the engine should be ok at least especially if I do a few of the upgrades like the injectors. I couldn't quite hear clearly but would the older 3.8 injectors fit also?
@justinsantarsiero3971
3 жыл бұрын
@@modeverything1 or what was that third injector you mentioned in the video
@davidcovan607
2 жыл бұрын
Are there any engines you can swap the lower intake with and then heads etc or just port and polish
@modeverything1
2 жыл бұрын
Yes you can swap to 3100/3400 heads but you have to use the matching intakes to the heads. The ports don't line up with the 3.1 heads. Push rods are also required and usually custom. I will try to do a video explaining this soon!
@davidcovan607
2 жыл бұрын
Hmm I'm sure the power increase would be 100% worth it but finding a 3400 that's a 1994 or 1995 may be hard to do unless the newer 1 will work
@modeverything1
2 жыл бұрын
It is especially with a cam upgrade. You can use any 3400 top end, the only issues would be with the egr valves being different. Someone used to make egr adapters but they haven't made them in years.
@davidcovan607
2 жыл бұрын
I can make a little plate and delete the egr all together but that's crazy if your saying I can run a idk 2000 3400 top end on my 94 3.1 engine that's awesome n prolly worth doin gotta look into the push rods and how to measure them will be waiting for your videos
@davidcovan607
2 жыл бұрын
Ah even better then so I can find like a 2005 3400 sweet but the push rod thing you mentioned will be the confusing part im shocked I can use such new stuff on a old block
@andrewjocar4507
3 жыл бұрын
Backyard youtube machinists
@JohnJackson-re4wo
2 жыл бұрын
Ay how can I make my 2.8 mpfi in my 1986 Pontiac Firebird faster
@modeverything1
2 жыл бұрын
There are a few things you can do, just depends how much you want to spend. Check out the v6 section on thirdgen.org forms, you will find lots of information and can see what kind of results you can expect from certain mods! Hope this helps for now, I may try to do some videos on the iron head engines down the road.
Пікірлер: 96