Wonderful, thanks for the video. I love Japanese motorcycle. I love that you have tubeless wheels
@pd8559
Жыл бұрын
Most excellent video. Other than the final drive what else has typically needed replacement by 30k miles?
@Yololife813
Жыл бұрын
I would check drum brakes, front brakes, coolant, bleed brakes, if clutch seems to slip relplace that too, spark plugs. Basic maintenance. Owner manual can be found on website.
@motorcyclistfromholland8856
Жыл бұрын
You overdone it. It’s almost always the splines on the shaft drive itself
@jimksa67
27 күн бұрын
Great attitude! I have a 91 VX800 60K k and hoping they greased spline properly. Thanks for the tips.
@mccslawg
10 ай бұрын
Thank you! Great video. I have a 2014 C50 BOSS. I love this bike. Your video I will save if and when I need to take on this job
@NattBram
17 күн бұрын
Cuanto aceite lleva y de que tipo? Saludos....
@mdjones905
4 ай бұрын
This manufacturer flaw I doubt is accidental, it’s intentional because it’s happened to too many.
@madhanakumar6155
3 ай бұрын
Nice video clearly briefed fr replacing final drive shaft. Where is the EBay need full address & contact # for my future requirement if any. I own c 90, boulevard is good bike from Suzuki.
@Yololife813
3 ай бұрын
eBay app you can order anything on there. Just do a search
@abelgonzaslez2103
Жыл бұрын
SO GREAT THANK YOU MUCH .
@AlexandreKlafke20
Жыл бұрын
Thx for the nice vídeo!
@gunr2012
Ай бұрын
Does anyone know where I can buy a replacement driveshaft for my 2009 c50????????
@Yololife813
Ай бұрын
@@gunr2012 eBay That’s where I got my
@rocxylemmon8535
5 ай бұрын
Thankbyou for this! You have a great spirit to do this to show us how to keep these bikes on the road.
@jnetane
3 ай бұрын
Great video! Thank you
@josephharris1869
4 ай бұрын
Thank you brother !! Putting mine back together today
@murcielagosky
6 ай бұрын
Just today, it happened to my wife's 2009 m50. Question. If you buy a used one from eBay, how would you know that it won't happen a year later again?
@Yololife813
6 ай бұрын
You won’t. It’s just a chance you have to take. Ask the seller how many miles is on the bike when the shaft came off. The less miles the better. When you get the used shaft inspect and put grease on the splines before install it. Good luck
@keithnguyen1436
Жыл бұрын
Excellent video. Where did you get the whole final drive assembly and how much if you don't mind me asking?
@Yololife813
Жыл бұрын
eBay. I think it’s $100
@robinson_crusoe_
11 ай бұрын
Hi there 👋. I start reassembling all of this final gear unit yesterday and had a question. Maybe you know how that bond 1207B should be applied? There are 2 holes for breather on final gear case. Thank you.
@Yololife813
11 ай бұрын
Sorry I don’t know how’s that bond or how to apply it. I just replaced the entire shaft drive.
@ronaldadventuresantos7220
3 ай бұрын
I need to find tubeless wheels for my boulevard 08
@Yololife813
3 ай бұрын
Try eBay?
@alisaleem6988
10 ай бұрын
Here you can explain how to open and change the clutch valves of a Susuki Boulevard C50 2007 bike.
@alisaleem6988
10 ай бұрын
Where is the predecessor of the engine operating, Susuke Boulevard, opening and installation diagram
@Devin-Roberts
2 ай бұрын
Just swapped mine out.. now my rear tires locked up😅😫
@Devin-Roberts
2 ай бұрын
At least now I have your video for two!
@Yololife813
2 ай бұрын
Did you figure out why it lock up?
@collosus81lash98
Жыл бұрын
Good video. How many miles do you have on it?
@Yololife813
Жыл бұрын
30000miles
@ChristCostanza
Жыл бұрын
Where did you find the whole final drive assembly like that? I am having the same issue and I'd like to replace every like you did, but the only whole assemblies I've found have the same issue...
@Yololife813
Жыл бұрын
eBay
@JooKed
Жыл бұрын
Question, how did you get the female coupling holder nut off? I'm talking about the one with the folded lip you need to pry open, but you need to hold the assembly in place to take the 22mm nut off, how did you manage? Vice?
@Yololife813
Жыл бұрын
I used my impact wrench
@alexandremiro
Жыл бұрын
Great video ! How long it took you the whole thing ? I see you take off your pullover while putting back the shaft in the yoke (that drop down a bit) and the video is cut. How did you do it ? Thank you
@Yololife813
Жыл бұрын
Took me little over 5 minutes get the shaft in.Just have to rotate the shaft and angle down. It will go in eventually
@alexandremiro
Жыл бұрын
@@Yololife813 Thank you !
@alexandremiro
Жыл бұрын
@@Yololife813 And what about the whole thing ? How long it took you more o less ?
@Yololife813
Жыл бұрын
@@alexandremiro probably little more than 2.5 hrs. If I did have to do the video, probably 1.5 hr
@alexandremiro
Жыл бұрын
@@Yololife813 Thank you !
@wesrutkowski5564
6 ай бұрын
I have exactly same problem , when you received the new drive shaft assembly was the shaft firm and not loose and wobbly like what you showed on this video?
@Yololife813
6 ай бұрын
It was loose but not much like the one on the vid
@wesrutkowski5564
6 ай бұрын
@@Yololife813 thank you
@olheghtt
Жыл бұрын
It looked to me like there were five bolts to remove that frame + the one bolt with the hex head, do those six bolts have a torque spec or do they just going tight with blue thread lock... Same question for the three acorn bolts.
@Yololife813
Жыл бұрын
I believe They all have torque specs. You can Google it I just hand tight them.
@olheghtt
Жыл бұрын
@@Yololife813 I'll double-check my service manual, Haynes manuals are not all that well written.
@محمدالفيفي-خ9ك
Жыл бұрын
Great job. May I know the part number that is not working?
@Yololife813
Жыл бұрын
I ordered on eBay the whole used shaft. There was no part number. If you need part #go on partzilla.com and look up part number on their site.
Пікірлер: 55