Hiya Mate! I just found ur chanel, I had a job scrapping the copper from old electric motors & we would heat them up in an oven for 2 hours,Chisel off one end of the copper wire then use a air atuated ram conected to a set of poly grips with chain to pull from the other end.The hardest part was waiting for the oven to heat them up.Keep up the good work!!
@lawrencelipon8673
Жыл бұрын
👍👍👍👍👍👌Great work and planning on the stator shear, and puller really enjoyed the video thanks for sharing!!
@AlwaysBored123
Жыл бұрын
Thank you for watching!
@cccorvette
Жыл бұрын
Great video....enjoyed the controlled destruction
@AlwaysBored123
Жыл бұрын
Thanks. It's always nice when you can get paid to break stuff lol.
@haynillesen
Жыл бұрын
Better good stolen than bad designed , but I haven t seen that V-shaped stator-holder before,that is a good design! simple things often work better than complicated things
@AlwaysBored123
Жыл бұрын
Yeah I just looked at as many commercially made units as I could find and tried to replicate the same mechanism more or less. The vee shaped support is necessary to keep the stator centered under the pointed blade, which is necessary to keep the stator from deforming excessively while cutting through it.
@haynillesen
Жыл бұрын
@@AlwaysBored123 I meant the V-shaped holder you use to pull the copper .The V-shaped bottom of the cutter doesn t allow the cutter to go deep enough to cut the stator in 2
@taunusrunner3767
5 ай бұрын
great work... i will bilding something similar in the next time
@danielnewman3210
Жыл бұрын
Impressive, very nice!
@billjunking_fool5549
Жыл бұрын
Thanks for the video I'm actually building in the process of building basically the same thing good information
@AlwaysBored123
Жыл бұрын
Good luck with it!
@m.weston7114
7 ай бұрын
Your cradle is solid, it needs to have a space in it for your blade to completely go through without bottoming out. The top of your blade would be more stable with a wider plate with at least two bolts going through it rather than one. Nice job.
@graysonedge
Жыл бұрын
your way of doing the job is way quicker, no need to heat the steel your way. will keep on watching ur stuff!! Thanks from New Zealand!!!
@AlwaysBored123
Жыл бұрын
Some are easy to pull but others I really struggled with. I was thinking of trying to heat them up to make them pull out easier. Thanks for the info glad to know that works.
@DavidGS66
8 ай бұрын
Solution is tell manufacturers to use a couple thicker slats in middle beveled for yout tool or for other tools such as machetes, meat cleavers, etc.
@rustyul
Жыл бұрын
I'd suggest some air hardening tool steel like a2 or A6 for the blade. It's not cheap. After heating the entire piece to about 1800° F. You would then temper it back to about Rockwell 56 which would be about a 400° F soak for maybe 3 or 4 hours depending and how thick it is. I would suggest 10 mm or 14 mm for the thickness of the blade, 3/8 in or half inch. You would obviously have to do all your shaping and edge forming before hardening. You will have to find somebody with a heat treating oven as it's almost impossible to do with the torch. You might be able to do something like 01 with the torch but you need to quench it in oil which gets to be messy and a little bit dangerous because of fire.
@AlwaysBored123
Жыл бұрын
Thanks very much. Would I need to worry about warpage during the process? I've never heat treated anything.
@rustyul
Жыл бұрын
@@AlwaysBored123 A2 and A6 show minimal distortion in heat treat. Maybe a couple of thousands in thin sections but nothing you would have to worry about in your application.
@matthewgregory395
Жыл бұрын
Can you brake down hard drives, love the channel
@AlwaysBored123
Жыл бұрын
If I get any I sure will. Thanks!
@DieselRamcharger
Жыл бұрын
little relief for that blade tip on the pusher block and youd be able to chop clean through.
@AlwaysBored123
Жыл бұрын
Yeah a little adjustment would make that work better.
@dirtdonthurt7606
Жыл бұрын
Great videos ,I have done business with that scrap yard for years verry rare will i go to c&c
@AlwaysBored123
Жыл бұрын
Wow small world. Yeah Morris is awesome I buy almost as much stuff from them as I sell to them lol. I'll go to C&C if I have to but they always complain about something so I try to avoid them.
@theEmpireofdirt
Жыл бұрын
Nice set up just found your channel. It might help to use a thinner blade. I was going to use a old circular saw blade because they’re generally tool steel. I’m also surprised to see you using air for the puller cylinder. I actually thought about using air but air compress and I figured it would get dangerous if I got a winding that was stuck really bad. It might turn the pliers and chain into a projectile. But it works really well.
@AlwaysBored123
Жыл бұрын
Yeah the air cylinder looks sketchier than it is. It does store a lot of energy but since it's pulling something apart that energy is always released in a way that creates a larger gap than before. So as long as you have a hand on the nippers to keep them from flying around and slapping you it's not too hazardous. The bad part is it's just not strong enough to pull really stubborn windings. But on easier ones it's very fast and efficient. A thinner blade in the splitter would probably be a good idea. I wasn't sure what I was doing so I chose 3/8" purely out of convenience. Whatever you use it definitely needs to be harder than AR400 though. I didn't know circular saw blades were tool steel thats interesting. Thanks for the comment!
@theEmpireofdirt
Жыл бұрын
The other thing you might be able to try is tempering the cutting edge to try to make it harder the hydraulics do pull a lot harder for the puller. I don’t think I found one that stopped mine it will actually taper the inside of the field housing, but it is slower.
@markb2007
7 ай бұрын
I have a coulter disc that is flat. I think it will work for a blade after I “V” it. I don’t know the hardness though.
@manueladame1462
11 ай бұрын
Good 👍 how much are you asking for the machine
@woodhonky3890
Жыл бұрын
Do they not sell single-phase hydraulic power units? Regardless, nice build!
@AlwaysBored123
Жыл бұрын
The do but not for $350 on facebook lol. Thanks!
@MikesMeltdown-sj8df
8 күн бұрын
Have you tried putting a hardened edge on the cutter with hardfacing welding rod?
@AlwaysBored123
7 күн бұрын
I have not. I think with the time and money you would spend doing that you would be better off making a blade out of tool steel tbh.
@patrickm.8425
2 ай бұрын
There's no reason at all to split those thin ones! Just cut one side of the windings off, then pull out the rest... done!
@curtisricks9043
Жыл бұрын
Could you heat treat the blade to harden it?
@AlwaysBored123
Жыл бұрын
Maybe but it would be a complex process that is difficult to find information on and would definitely require a lot of trial and error. The whole point of using hardened plate in the first place was so I wouldn't have to fool with hardening it myself lol. Next time I'll try some AR500 or 600 and I'm sure that will be more than hard enough.
Пікірлер: 39