kzitem.info/news/bejne/yJ-iqm2ErKGGZn4 Making mini drill using the same setup
@selivanyro
4 жыл бұрын
Watched from USSR and it was a good explanation!
@Gonzb023
3 жыл бұрын
Damn I'm such an idiot. I plugged in my esc to the tester like you did but then my stupid ass plugged in the battery to the other end of the tester and fried the whole damn setup. Ugh! Wish I had seen this sooner
@garyvale8347
2 жыл бұрын
speaking as someone fairly new and also buying a sevo tester, ( mine came with no instructions ) ..I can understand how you did that....I would have never thought of plugging the ESC and battery into one of the " out " ports.....the 4.8 - 6.00 vdc side 3-pin port is strictly for powering the tester with a stand alone power supply...and the voltage match is critical....
@garyvale8347
2 жыл бұрын
speaking as someone fairly new and recently buying a servo tester, ( mine came with no instructions ) .....I would have never thought of plugging the ESC and battery into one of the 3-pin " out " ports.....also , I thought the single 3-pin ( IN ) port marked 4.8 - 6.0 vdc is strictly for powering the tester with a stand alone power supply ( and the voltage match is critical ) .... also thought that all servos and motors need to be connected on a 3-pin connector , marked " OUT " .... thanks
@awaitingthetrumpetcall4529
Жыл бұрын
Thanks for posting.
@DHAVALPATEL-bp6hv
4 жыл бұрын
Hi, there !!! Nice video , nice work , keep working and keep posting new videos !!!!
@tobyayres5901
4 жыл бұрын
Thank you helped so much 😀👏👏
@TechsScience
Жыл бұрын
When I connect my servo to tester all the lights glows up & servo begins to rotate randomly Is there any solution?
@Shion0Hibiki
2 жыл бұрын
I'm thinking of using this to control the speed of the escooter motor. Plugging the cable from the trigger to the tester then to the esc.
@kurachajayasaikumar1355
4 жыл бұрын
Hello sir I had doubt regarding this bldc motor....i.e just we need the battery,motor,esc and servo tester These are enough to run a motor right....
@techysinsight
4 жыл бұрын
Yes
@gungriffonbr
Жыл бұрын
very hepful for me today
@Raja-hv8gj
5 жыл бұрын
My brushless motor not run...its sound like beeping beeping not run I am using a servo tester....3500kv with 40a ESC
@techysinsight
5 жыл бұрын
Check with a different motor to verify whether the servo tester is ok This happend to me when my servo tester went faulty
@induvishwakarma8962
4 жыл бұрын
Agar mai is esc me 2700kv ka brushless motor laga dunga to kuch problem nhi hoga na?
@techysinsight
4 жыл бұрын
Nahi
@induvishwakarma8962
4 жыл бұрын
@@techysinsight thank you
@induvishwakarma8962
4 жыл бұрын
Kya 2700kv ka brushless motor isse bhi speed chalega?
@induvishwakarma8962
4 жыл бұрын
2700kv ka brushless motor 30A ke kisi bhi esc me laga sakte hai kya?
@techysinsight
4 жыл бұрын
You can use any 30 amp esc available
@diegoarpino2080
4 жыл бұрын
Is there a way to do this with an ESC without a BEC?
@hercules71717
4 жыл бұрын
Can I use a 12V 30Amps SMPS instead of the Battery?
@techysinsight
4 жыл бұрын
Yes you can
@techysinsight
4 жыл бұрын
Can use laptop charger
@techysinsight
4 жыл бұрын
Yes
@KL-bc1eg
3 жыл бұрын
I'm using a 12V car jumper starter battery with usb volt changer/regulator. You can use any battery really. I use the motor as a rotary cutter/drill/sander.
@ivanbankovic6410
4 жыл бұрын
Why moror can works only few seconds and than he stops until I again restart proces(by rotating taster)?Can it somehow work without break?
@techysinsight
4 жыл бұрын
There are 3 modes in the servo tester press the button to change
@techysinsight
4 жыл бұрын
It also happens when your battery has less power
@ivanbankovic6410
4 жыл бұрын
@@techysinsight Yes first mod is slowly lose power , second mod is he start with max power and also lose power and third he turn on and of on evry second or two. But it cant hold motor on , constantly for 10 seconds without losing power.
@ivanbankovic6410
4 жыл бұрын
I have strong battery , but even if i use first mod and tune it to go slow and use less energy motor stops after few seconds.
@techysinsight
4 жыл бұрын
Ok can check with a different esc
@k_berm9deddy93
3 жыл бұрын
is it after using servo testing, esc is calibrated again with RX TX?
@techysinsight
3 жыл бұрын
No there is no such thing Servo tester is a setup without tx
@GoogleEarth1988
4 жыл бұрын
hi
@user-co9nc
4 жыл бұрын
can I run stepper motor 6 pole
@techysinsight
4 жыл бұрын
Hopefully yes You can test servo motors with this .since I don't have a stepper motor I personally have not tested yet.
@uniqueium3547
3 жыл бұрын
My motor is no working with servo tester,,,only beeping one times,,and motor start vibrating on increasing power....pls help me....is there any solution
@techysinsight
3 жыл бұрын
Check the soldering And it happens when the battery is underpowered or faulty Also maintain minimum position in the servo tester before atart
@uniqueium3547
3 жыл бұрын
@@techysinsight I have done both things,,charged full battery ,and also check minimum position of servo,,,,but when I connect power, servo beeps only once ,,and on increasing servo power,,,motor start vibrating (not rotating)....
@techysinsight
3 жыл бұрын
Then may b the motor is faulty
@uniqueium3547
3 жыл бұрын
@@techysinsight thank you techys insight for your advice and help
@akg5012
4 жыл бұрын
Are you experiencing malnutrition ?...cant hear/understand anything you saying
Пікірлер: 45