Very helpful. I took apart my air brush to clean it. I am a beginner and I freaked out. Until I saw this. Thanks mate!. Just one thing to add. The trigger goes into the hole below from where the pressurised air comes. Just add that little detail as it seems to be missing. I had a hard time guessing where to fit the trigger. Cheers!!
@WatchItPaintIt
Жыл бұрын
Yeah the trigger & trigger guard are the most annoying parts to re-attach.
@Fluidpysankymasterartist
9 күн бұрын
@@WatchItPaintIt OMG! Aint that the truth!! I too am new and was a nervous wreck thinking the same thing as @arshadhasan, that I wouldn't get it back together.Everything came apart and went back together just fine... until the trigger. So I was trying to figure out does the little piece on the bottom of the trigger ( the part that bends back and forth) does that go inside the hole that i saw inside the brush or does that bottom part lay flat or where the heck does it go! So I fiddled with it for like an hour until it finally seated itself properly, so I knew it was in right, but I still don't know where that very bottom of the trigger went to, if it laid flat or if it went into that hole?? Oh boy!!! Thanks so much for a GREAT vid, I musta watched 10 ones on how to take apart and put the brush back together, but you finally gave me the courage to just, DO IT Patty!!! lolol
@shawnc4240
2 ай бұрын
IF YOU HAVE THE AMAZON MEEDEN AIRBRUSH! : Put the trigger in, then the needle (the guard is on the needle) turn the whole thing upside down so the guard falls through the gap behind the trigger. screw everything back on!
@chrisdavidson2810
6 ай бұрын
Thank you, very helpful… I was lost lol
@MoMsLiKe2GaMe2
10 ай бұрын
THANK YOU! Best breakdown n rebuild! Much more thorough than others. I was stuck with the trigger and you nailed it! 😊
@WatchItPaintIt
10 ай бұрын
Glad it helped!
@cava1962
5 ай бұрын
Great video Thanks for sharing..!!
@JS-oy2jm
10 ай бұрын
Very helpful. But, when I took mine apart to do the deep cleaning, the spring came out and now, being a beginner, I can’t put it back in. Or I’m trying to put it in the wrong spot. Does it go before the trigger in that part of the casing? Or behind it?
@georgenarciso8747
9 ай бұрын
thanks for sharing the tips
@sheevlogs9608
3 ай бұрын
Thank you so much. I was searching where I can found this vidio.
@WatchItPaintIt
3 ай бұрын
Glad I could help!
@deborahklena5044
Ай бұрын
How do you operate it with a compressor
@joannicfuentes5313
3 ай бұрын
I recently just got an airbrush gun and took it apart of course i had my anxiety attack! but now its a panic attack because after 3 hours of learning how to assemble it back now the gun is just spraying air and not the product I cleaned it out already as well but i dont know what it might be I am seeing that it might be the needle chucking guide any advice or suggestions on what it might be ?
@WatchItPaintIt
3 ай бұрын
Sometimes it's the trigger mechanism, but it's hard to tell without seeing it. Is the trigger guard pressing snugly against the trigger?
@thrackmoorinvictus5948
2 жыл бұрын
While it is disassembled, lightly lube the moving parts and the needle.
@WatchItPaintIt
2 жыл бұрын
Yes indeed! I was going to do a cleaning video later and mention that :)
@FalconWing1813
Жыл бұрын
I got a airbrush a while back but never use it due to not having the time to break it down each time i get a free moment to paint. Do you half to break them down each time ?
@WatchItPaintIt
Жыл бұрын
No - only for a deep clean, which you don't need to do very often. For a fast clean, tip the extra paint from the cup into a waste container, add water to the cup a few times and dump that out, then add some cleaner and swish that around with a brush, dump. Then just spray a bit of cleaner and water thru the end of the brush to finish it off. Takes 2 minutes to clean it that way. You only need to take the airbrush apart if it's constantly clogging. Even then you can usually get away with pulling out the needle, cleaning and lubricating it and then put it back. Hope that helps!
@FalconWing1813
Жыл бұрын
@@WatchItPaintIt Yes huge help! That will save me alot of time! Thanks for explaining that and thanks for the reply have a good one!
@oliverp3545
2 жыл бұрын
Why does your handle look like a sonic screwdriver?
2 жыл бұрын
Because it an airbrush is a piece of Sci-Fi from the 60s
@Diabeto.biscuit
Жыл бұрын
Thank you I thought I post a piece but turned out that it was just in the wrong place
@Timeremortem
11 ай бұрын
What if my needle chuckle guide and my needle dont come apart? they are like 1 piece?
@ajdominique8519
5 ай бұрын
Same
@Timeremortem
5 ай бұрын
@@ajdominique8519 I managed to figure out my airbrush. Trial and error. :/
@philipmccann2358
5 күн бұрын
You really sounded like Kermit the frog after his voice broke !
@user-tm8dq7sw4o
Жыл бұрын
I lost my trigger guard. It wasn't this model. I'm stuck
@WatchItPaintIt
Жыл бұрын
Oh no!
@golnectr
5 ай бұрын
Let's just skip the annoying part
@Druss1The1Legend
2 жыл бұрын
Please dont pull your needle from the back, you chance bending the tip
@timofkings5173
2 жыл бұрын
People beyond the Neanderthale-era are fully capable of pulling out needles out the back of Airbrushes… Sorry, but this comment comes up on each Airbrush-video… and it’s a nonsense comment.
@Dopey661
2 жыл бұрын
I’ve literally never seen it pulled out any other way
@WatchItPaintIt
2 жыл бұрын
I always do it very gently!
@guylaindeschenes9793
2 жыл бұрын
With this model of needle, the only way to remove it is from the back. Look at the blue part at the end of the needle and you will understand.
@WatchItPaintIt
2 жыл бұрын
@@guylaindeschenes9793 It's true. After reading that comment I looked at my airbrush and thought "is there a secret way of removing the needle I don't know about??" :D
Пікірлер: 36