This literally saved my Switch, thank you so much for the detailed tutorial!
@hawkfeather6802
3 ай бұрын
Boy,this is complicated. Good to keep in mind for emergencies
@diegoandresas
2 күн бұрын
My Switch oled live again!!! Thanks!!!
@enesdasilva2357
3 ай бұрын
Please post a video about BAN removal. I get excited when I get a notification from you channel saying there will be a video about this.
@rohansharma8956
3 ай бұрын
Not possible, Nintendo had really beefed up security since the 3ds.
@braianmanueljoaquinleonor9380
3 ай бұрын
@@rohansharma8956 do you think using this metod i can fix the start up messenger can't run this software ?
@rohansharma8956
3 ай бұрын
@@braianmanueljoaquinleonor9380 u can fix that by reinstalling the game and updating the sigpatches (latest HATS pack has them). U don’t need to reinstall the nand for that
@braianmanueljoaquinleonor9380
3 ай бұрын
same error at end could not start the software hahaha
@marcoganci8358
3 ай бұрын
there is no method available to remove the ban from the nintendo switch, advice for life: next time be more careful and set up all the necessary defenses to avoid the ban
@jimzcoi
Ай бұрын
Hi! Thank you! With your tutorial I've fixed my console!
@spaycker
Ай бұрын
Great video. It worked for me to perform a test, my oled switch does not dump the nand nor create emunand, however I managed to separately dump all the partitions except "SYSTEM" and "USER", so with your method I created my Donor nand, and with this nand I created my "emunand", after several errors and attempts I managed to boot the emunand, however after some time the console crashes and it takes a long time to enter the emunand again. I probably have a physics error in my physical nand module.
@snoopysnoopy7417
3 ай бұрын
good video thx bro have a nice day
@diegotarifa8627
2 ай бұрын
EXCELENT MORE EFFICIENT THAN THE NORMAL VIDEO AND TOOO FAST!!! 3 SWITCH REVIVE FROM DEATH WITH THIS NEW METHOD
@jaxliel0779
3 ай бұрын
ohhh man is amazing this tutorial if jajajaja thank you very much ammm coming soon I donading :)
@teepat
Ай бұрын
saved my console tysm
@granderpro1
3 ай бұрын
Hi! Will be new method 3 guide?
@sthetixofficial
3 ай бұрын
yes it is similar to the level2 but with additional prodinfo_gen procedure
@riuneharu
26 күн бұрын
Thank You, this fixes the OLED switch with stuck logo issue after modchip installation Is it is safe to connect the sysnand to the online server?
@sthetixofficial
23 күн бұрын
yes if you dont have pirated games on it.
@itechconsole
3 ай бұрын
great tutorial as usual THANKS a question, what tutorial should I follow if I don't have any nand files, maybe I only have the PROD.KEYS, the nand is bad
@sthetixofficial
3 ай бұрын
you need to do the level3 guide .(this guide + the prodinfo_gen guide)
@itechconsole
3 ай бұрын
@@sthetixofficial thank you
@jjchen6360
2 ай бұрын
@@sthetixofficialMay I know if you have a video for level 3? I cannot backup my nand as well… all missing….
@andreynikan1105
2 ай бұрын
@@sthetixofficialhello. Could y explain the order of actions? I should start from prodinfo guide and finish by level 2?
@sthetixofficial
2 ай бұрын
Yes, do the prodinfo_gen guide, and do the level 2 (the updated version)
@josuesalazarplaza6821
2 ай бұрын
Hi, I have a problem with a friend's Switch, he used SYSNAND all this time, even though he had EMUMMC installed, his SYSNAND got corrupted and he can no longer use OFW, but the EMUMMC boots normally and can be used. Can I make a copy of the EMUMMC and transfer it to the EMMC? Please help me, I am using a translator to write this
@sthetixofficial
2 ай бұрын
You can!.
@cetrodorei
3 ай бұрын
Hey, It would be cool if someone made a video comparing the performance of the distros Ubuntu Bionic vs Ubuntu Noble vs Fedora 39 (L4S 5.1.2) running Gamecube, Wii or other real world benchmark test (without overclocking) to see the general optimization of the new available Linux for Switch.
@baspav
29 күн бұрын
Excellent video! Thanks, one more switch saved from brick. Any idea why Console Serial number is XAW1000000000? after unbrick? I boot to ofw with no SD inside (unpatched).
@sthetixofficial
28 күн бұрын
do you have the original prodinfo from the console?
@baspav
28 күн бұрын
@@sthetixofficial I am not sure. The console's SD was a mess with a prodinfo files and a generated prodinfo file. It's not mine.
@sthetixofficial
26 күн бұрын
then you dont have any other option.
@rodolfoferreira5582
Ай бұрын
Hi sthetix, I was gaming on my Switch Lite + Picofly (RP2040) and then I had to re-do the soldering on the daughterboard connector because my left d-pad wasn't registering, which had me desolder RP2040 from the board. After the job was done, I resoldered everything but now my Lite will black screen when sd card is inserted & no backlight; but when card is removed, backlight comes on and the "no sd card" is displayed. Could that be a bad nand, did something get corrupted? I'm on the Lite, if those are the issues, will this video help me out?
@sthetixofficial
Ай бұрын
it could be anything, because as far as I know, the pico could kill your console
@thediamondcraft6438
2 ай бұрын
I have a question. My switch is bricked and the PRODINFO, and USER partition is missing. But luckily i have prod.keys, and PRODINFO file backup from the past can i can restore my Switch with this method?
@sthetixofficial
2 ай бұрын
you can follow this guide to make a new nand
@SonicKidXD
Ай бұрын
I got a question I mainly want to fix the Emunand part of the switch is the process the same as sysnand
@sthetixofficial
Ай бұрын
yes it is the same but using the level2, it will wipe everything, so try using the level 1 guide first
@SonicKidXD
23 күн бұрын
@@sthetixofficialgood news my sysnand finally works again but now I’m trying to fix the Emunand pkg 2 decryption failed problem but I don’t want to erase everything on it because that’s what I use to play my switch is there a solution?
@sthetixofficial
23 күн бұрын
try doing the level1 unbrick , the newest method.
@arthurantoniassi9950
Ай бұрын
Hi, I can't backup nand because at 90% error reading 8192 block @ LBA 03488000 and when I try to access the system error code 2002-3580 which tutorial should I follow ?
@sthetixofficial
Ай бұрын
i think your emmc chip is damaged, or maybe your SD card is damaged, please try to replace the SD card and backup the nand again.
@arthurantoniassi9950
Ай бұрын
@@sthetixofficial I already tried to use a different SD card, but i have the same error, what else should I try? ?
@ahkki54
3 ай бұрын
Hi sir i need your help please, i have v2 with firmware 17.01 using hats pack, everything is fine until i boot into ofw to factory reset and online update firmware, but both give me an error and was not successful, then my switch cannot boot into ofw anymore. Today i follow this video to rebuild sysnand to v18. 01 using my backup keys. And then i create new emmc from newly build firmware 18.01,emmcfw can boot successfully. But semi, cfw, ofw all stuck at ns logo.
@sthetixofficial
3 ай бұрын
check your fuse count please.
@ahkki54
3 ай бұрын
@@sthetixofficial fuse count 19,HOS 17.0.0+ I think 18 firmware should work?
@ahkki54
3 ай бұрын
@@sthetixofficial step i already done today, rebuild nand using firmware 17 and 18,,recover using console backup which is v17. 0.1,reformat sdcard with latest hats pack, non of them work, still stuck nslogo in ofw/syscfw.
@sthetixofficial
3 ай бұрын
well, maybe the emmc chip is damaged or something else.
@ahkki54
2 ай бұрын
@@sthetixofficial hi today i try to remove pico rp2040 chip and install back emmc to the original position, suddenly the system can boot up normally, i follow the initialize setup and shutdown the system, afterthat, i reinstall back rp2040 picofly, its become normal back and boot up as usual. Thank you for the great video, learn alot from your channel
@AdamTheHammer
Ай бұрын
when trying to encrypt and dump the console prodinfo to the encrypted folder its saying bad crypto and im unable to dump it, what have i done wrong?
@sthetixofficial
Ай бұрын
please re-watch the guide.
@mcdarkrevolution
2 ай бұрын
Yeeeeeeeeeeeeeeees!!!!
@genkidoesgaming
3 ай бұрын
@sthetixofficial Hi, I was wondering, out of curiosity, if I can use this method to create a clean nand for oled which can be compressed highly. I saw your Twitter post regarding the compression. I would like to be able to get a good ratio like that so it's small enough to store in the cloud. I have a full backup of sysnand already. I'm looking to replace it if it is safe. Hope you can clarify. Thanks in advance!
@sthetixofficial
3 ай бұрын
no you cannot. the only way to get a 650MB compressed NAND is to dump it after you mod it.
@genkidoesgaming
3 ай бұрын
You mean to mod before actually using it at all and then wiping before modchip install?
@sthetixofficial
3 ай бұрын
@genkidoesgaming no, update the console to the latest, no need to link the user profile to nintendo. then mod it and dump using hekate.
@genkidoesgaming
3 ай бұрын
Too late for me, I guess. I used s demo games on my oled before factory resetting. then wiped it and sent it for a picofly install. They made a nand backup, but when I compress the nand it's only a bit smaller than 64gb.
@sthetixofficial
3 ай бұрын
@genkidoesgaming you can try it later with a new console.
@ZepettoNuke
22 күн бұрын
hi sthetix, I have an OLED console and a purple screen of death when loading the official firmware, but in Atmosphere on sysnand everything worked, I did everything according to the instructions and now it gives an error (ini1 parsing failed) when loading, I transferred everything several times the result is the same, firmware 18.1.0 downloaded 18.1.0-1.0 I also tried to install 18.1.0 without 1-0, the Nintendo logo appears and a black screen, tell me what it could be? or what did I do wrong?
@sthetixofficial
21 күн бұрын
try to repair it with the guide or at least the level1 guide
@ZepettoNuke
16 күн бұрын
@@sthetixofficial Same problem, ini1 parsing failed I redid everything several times, every time the same problem, I don’t understand what I’m doing wrong
@sthetixofficial
16 күн бұрын
i dont know about parsing, where did you read it.
@ZepettoNuke
13 күн бұрын
@@sthetixofficial This message appears when boot up ofw
@fox265634
2 ай бұрын
in the minute 11:43 the nxnandmanager show this error (failed to mount filesystem) what should i do?
@sthetixofficial
2 ай бұрын
you need to install the dokan driver
@End_Times_Dreams
Ай бұрын
If you keep getting the error towards the end where you mount and copy the files, run the NX took as administrator
@AlonCV
2 ай бұрын
Hey! I followed all the steps but in the step to "Restore eMMC ALL", when I press POWER to continue, immediately "finished" the process with "Time taken: 0m 0s." but nothing shows in all (just the text of "Time taken", nothing more), it's a Hekate bug? Idk how I can solve it, please help :(( I thought the process would have already been done, but when I started SysMMC it show me the "pkg2 issue, Failed to boot HOS!"
@sthetixofficial
2 ай бұрын
you did not put the files inside the correct folder. please check again and maybe you did not remove the file extension.
@AlonCV
2 ай бұрын
@@sthetixofficial it's weird because i remove the .bin of all the "bcpkg2" and "boot0 and 1" files, and it's in the correct folder called "partitions" :( but with or without the missing files, the "restore emmc all" option doesn't work for me and only shows the "Time taken 0m 0s" EDIT: Idk what I did, but after bricking again my eMMC with that issue of "Time taken: 0m 0s", I decided to restore my nand backup (backup that I made several weeks ago) (BOOT0, BOOT1 and all the "rawnand" files), and when I decide to boot to SysMMC, magically boots with the Switch logo and nothing show any Atmosphere error or anything, just boot normally and immediately I turn off the Switch to boot Hekate, and when I boot Stock/OFW, it also boots too!! Again, Idk what happened in all, but I guess it is because my nand backup has the bcpkg2 partitions and seeing in GitHub and GBATemp forums, the reason why my switch was bricked is due the corrupted PRODINFO or saves (I highly doubt that you save them because when I deleted the ones that were recommended, when I boot OFW or SysMMC, just shows the Nintendo/Atmosphere logo and black screen forever, so my suspicions was the corrupted PRODINFO, and thanks to your tutorial, all the files with your donor nand and my prod.keys restores the corrupted PRODINFO, and only the latest issue was the bcpkg2 partition missing, but with my nand backup restored it without problems, and yeah, that's why my "variant" of your tutorial (and thanks!) (only in the case of the "Restore eMMC ALL" doesn't work for anyone, just use your nand backup as a complement for restoring the bcpkg2 partitions) :)
@sthetixofficial
2 ай бұрын
@AlonCV all switch consoles have the bcpkg2 files. I guess your alphanumeric folder is not correct or doesn't match so hekate couldn't pick them up
@AlonCV
2 ай бұрын
@@sthetixofficial yeah, probably is it, anyway I can unbrick my switch with the "extra step" i do (basically restoring my backup made to restore the missing bcpkg2 files, and the only corrupted file probably was my PRODINFO or saves), thanks for the tutorial! :DD
@dydaGames
3 ай бұрын
Boa noite, tenho switch oled eli ligar aparece o logo nintendo e depois disso ficar tela preta
@dashannsche8460
3 ай бұрын
Does such a method also exists for (New) 3DS console?
@sthetixofficial
3 ай бұрын
the ntrboothax
@dashannsche8460
3 ай бұрын
@@sthetixofficial Thanks for answering!
@dashannsche8460
3 ай бұрын
@@sthetixofficialWould you mind quoting the video you are referring to? 🙏
@sthetixofficial
3 ай бұрын
You can search the ntrboothax on my yt channel.
@dashannsche8460
3 ай бұрын
@@sthetixofficial Will do. Thank you so much, your work is highly appreciated!
@houwentien7529
2 ай бұрын
Nxnandmanager keeps crashing when copying system files while being mounted. either it crashes like in your video or the transfer just slows down to 0kbps and sit there forever. any other tools/method that i can use to finish this transfer?
@sthetixofficial
2 ай бұрын
shorten the USB cable, change your USB port. Or use the older level 2 unbrick guide.
@End_Times_Dreams
Ай бұрын
Try running as administrator
@AdamTheHammer
Ай бұрын
for some dam reason its saying my prod keys dont match up with the prodinfo file, ive dumped them from the console time and time again and its always coming back as bad crypto
@sthetixofficial
Ай бұрын
your prodinfo and your prod.keys should match. please check it by opening the prodinfo file using the nxnandnmanager along with your prod.keys obtained from the lockpick_rcm
@AdamTheHammer
Ай бұрын
@@sthetixofficial I've done that time and time again. I've even saved both the new dumps in a folder called new dumps to avoid confusing them for other dumps I've saved. It's bad crypto every time. The only thing I can thinnnkf is if someone has tried doing this before and messed it up?
@villaflorestv4537
3 ай бұрын
Hello. After installing the modchip. Sysnand wont boot, and blackscreen after nintendo logo, after removing the modchip its still the same. Only emummc boots. V1 patched is my device. What version do you recommend to use. All emmc info is there and the user partition is there also.
@villaflorestv4537
3 ай бұрын
Okay done on using this method and its show emmc is initialized in slower mode. I've read your issues with the picofly core modchip and its the same one that I've used. So my emmc is dead already? Should I swap it with new emmc and change the modchip? Or just the modchip?
@sthetixofficial
3 ай бұрын
you should not be using the pico. please use the instinct-nx or hwfly
@villaflorestv4537
3 ай бұрын
I did a DIY thing but I have experience in microsoldering, so the emmc is now broken? Because after I remove the modchip its still the same it cannot boot in sysnand, should I replace the modchip and the emmc?
@sthetixofficial
2 ай бұрын
Yes, replace the modchip, and try to unbrick it using my level 1 or level 2 guide.
@egormall33
Ай бұрын
@@sthetixofficial but what a problem with pico?
@johncaceres4165
2 ай бұрын
Hi there, my switch was originally hacked with sxos. I did something now it has hekate. But when I attempt to boot cow emunand or cow sysnand it gives me the message: "Unknown pk91 version. HOS version not supported!" but my OFW Launch does work. Can you advise on which guide I should follow to fix this and use my hacked switch.
@sthetixofficial
2 ай бұрын
try re extracting my hats pack, t.me/HATSPACK
@johncaceres4165
2 ай бұрын
@@sthetixofficial it gives a different kind of error now. I click Sysmmc cfw but after the switch logo it says error code 2168-0001 (0x2a8)
@sthetixofficial
2 ай бұрын
if ofw launch normally, the sysmmc should be able to work too. delete everything inside the sdcard and try to re extract the pack
@johncaceres4165
2 ай бұрын
@@sthetixofficial I removed the folder under /atmosphere/contents that matches another long number in my error message that ended in 7E51A and tried again. That worked. Found it on a Reddit thread.
@MonasChinasReales
2 ай бұрын
Can this method keep the online from stock firmware? (I'm not banned and I have my ProdInfo)
@sthetixofficial
2 ай бұрын
you can as long as your console is not banned previously
@Serpicus007
3 ай бұрын
hi, I should solve the problem "failed to match warm boot with fuses"....can you help me? Thanks.
@sthetixofficial
3 ай бұрын
that's not the solution. The solution for your case is to update your console to the latest firmware (on both sides - the sysmmc and emummc)
@Serpicus007
3 ай бұрын
@@sthetixofficial Ok, do you have a simple guide to recommend?
@sthetixofficial
3 ай бұрын
yes please watch my daybreak guide (offline update)
@Serpicus007
3 ай бұрын
@@sthetixofficialunfortunately I can't start daybreak, atmosphere doesn't start, that error message always appears.
@sthetixofficial
3 ай бұрын
You should IGNORE that message by pressing the Power button. It should boot to Atmosphere.
@user-du5lt5ij7h
3 ай бұрын
I cant seem to be able to get your new HATS pack,I did successfully do this a couple yrs ago.
Пікірлер: 125