Was just gonna order the niche kit. But now am gonna think about it a little bit more. Thank you 🙏
@jzsquad6866
2 жыл бұрын
Finally a video
@TyCurrdog020
Ай бұрын
Question. What jets are you running for the 686 kit in the carbs?
@craigdavison7632
2 жыл бұрын
Sounds like you had a better experience than me, my sleeve slipped
@Hunters_Mechanics
2 жыл бұрын
Seems to be a common issue at this point according to my other videos. Other than cheap manufacturing, I have no clue what causes them to drop
@hidinfrombiden6251
2 жыл бұрын
@@Hunters_Mechanics whenever you put a few heat cycles on those junk chinese cylinders the sleeve drops. There's no head gasket in the world that will seal when that happens. The reason you have so many hours on yours is because you had your cylinder deck height shaved down to match the cylinder sleeve height. Despite doing that, after awhile it may continue to drop even further. So you're basically playing Russian Roulette with your engine😂.
@Hunters_Mechanics
2 жыл бұрын
@@hidinfrombiden6251 I'm just hoping it lasts till I get out of college so I can start making money and not pay for cheap shit 😂
@hidinfrombiden6251
2 жыл бұрын
@@Hunters_Mechanics I can definitely understand that. Good luck to you man.
@Hendogg28
11 ай бұрын
That sleeve can only go down so far. They press into a grove in the cylinder. If one moves downward it’s because it wasn’t pressed in far enough to start with. All cylinders are made this way. I all ways heat them up to around 350 degrees in an oven and make sure they are pressed in all the way fool me once shame on you, fool me twice shame on me.. lol 😂.. So any cylinder I buy I check this first before I build an engine as why I make that 85 bucks an hr building them. I’ve used 100’s of these cheap cylinders on top end rebuilds. Only ever had a few problems and it was before I started heating them and throwing them in my press and making sure they were seated properly.. Good luck hope it helps..
@luisinvestors5982
4 ай бұрын
I need help whit my raptor 660 I put the time but no work
@rcvlogs3743
2 жыл бұрын
I had this kit and the wrist pin failed and shot the piston through my head and 7000 rpm
@Hunters_Mechanics
2 жыл бұрын
Did you have your brown pants on that day when it did? Lol
@XXXCRSPL
Жыл бұрын
Mt buddy bought a niche head assembly for the timberwolf and the valve seats needed recut and lapped in because there was no compression and couldn't figure out why till he pulled the head back off
@Hunters_Mechanics
Жыл бұрын
You really got to check every part you buy regardless if its cheap or not lol especially more when you're getting it from Niche
@XXXCRSPL
Жыл бұрын
@@Hunters_Mechanics He just assumed and just went with it..Lesson learned lol
@rancherjulian9872
2 жыл бұрын
What size jets are you running I just got the same big Bore and I’m have if problems jetting if
@Hunters_Mechanics
2 жыл бұрын
The jets im running do not have a stamp mark anywhere on them so I have no clue what size they are 😒
@matticus6339
Жыл бұрын
Rancher 350 with niche cylinder and piston, OEM head. Either the Niche cylinder bore is to big, or the piston is to small, had tons of piston slap. I bought the rancher with the cylinder already on it, its now tore apart on my bench.
@Hunters_Mechanics
Жыл бұрын
I checked my piston and cylinder gap before I even put mine together, along with the rings because I didn't trust it lol surprisingly enough mine was in spec
@matticus6339
Жыл бұрын
@@Hunters_Mechanics Yeah whoever put this one together didn;t check anything. Horrible.
@Hunters_Mechanics
Жыл бұрын
@@matticus6339 its exactly why I can't trust people to do this work for me anymore lol I make videos to help people avoid it
@matticus6339
Жыл бұрын
@@Hunters_Mechanics For sure, they also broke a bolt off in the case among other things, I think what I am going to try for now is see how a Wiseco piston fits in the niche cylinder. All the OEM cylinders on ebay need to be bored out.
@Hunters_Mechanics
Жыл бұрын
@@matticus6339 you might get buy with a used jub and a new piston if you hone the cylinder, thats the route I plan on doing when this kit breaks again
@BigDog-tn8re
Жыл бұрын
Maybe I’ll stick with Wiseco. Thanks
@Hendogg28
11 ай бұрын
There pistons are good but there crankshafts are garbage. Have one right now with less than 5hrs on it and the ristpin bushing is bad. Everything in the engine was new oil pump and bearings and seals. Should have just spent the money and put a stock assembly in it..
@timrogers9440
2 жыл бұрын
I need you to do a video on installing a axel into a swing arm lol the other videos I find are junk
@Hunters_Mechanics
2 жыл бұрын
I did record most of mine when I got my new one and then school got in the way so I just put it together so I could ride 😂 ill have to take it out again sometime and make sure to finish the video
@timrogers9440
2 жыл бұрын
@@Hunters_Mechanics please do your videos have helped me a lot. I have a extended swing arm and axel I want to install but I don't know how to do any of that lol
@Hunters_Mechanics
2 жыл бұрын
@@timrogers9440 I'm glad to hear that! Been looking for more videos to produce, my 4 wheeler has been running great (knock on wood!) And shit hasn't broke for a while so I'm running out of ideas 😂 ill see if I get time soon for that, currently have a few tutorials of my truck in the making then back to Raptor content
@jacka4265
7 ай бұрын
It's not like your mom's makeup.. It's Co-medic gaskets NOT cosmetic.
Пікірлер: 31