Hello Pirate, nice improvement. Not sure if in this Boyueda LCD the pin mappings are same/similar, but in my Laotie Ti30 LCD (the physical aspect is similar but the board is a bit different), I found that the 6 pin connector consists of: * 60 Volt positive input - red; * 60 Volt output (when turned on) - orange; * Ground - black; * Hall Effect sensor output - green; * RX - yellow; * TX - blue; Doing a continuity test, this green wire sensor output goes straight into the hall effect sensor output (pin 3 on the 49E chip). So for those not willing to modify the LCD, the user could make an adaptor cable that would skip the Hall output from the LCD, and use the one from the 108X thumb throttle. This cable could contain a 60 Volt to 5 Volt DC/DC converter in order to provide the correct voltage to the 108X thumb throttle.
@sterl_roof
Жыл бұрын
I want to install thumb throttle on my laotie ti30, any suggestions other than moding extra wire to bypass and all of that?
@JohnEdwa
4 жыл бұрын
To make a finger throttle actually usable, you need to tilt it down quite a bit so it is in a more ergonomic position. Usually, it needs to be horizontal or even tilted downwards, exactly like your brake lever is. If you have it pointed up like that, it's no wonder you find them hard to use. Again, exactly like your brake lever, imagine turning it to that position and how impossible it would be.
@verbsy
4 жыл бұрын
Awesome Pirate the throttle was one of the first things that i questioned when looking for my scooter ! i have been on motor cross and trails many years in the passed ! and braking with the throttle set forward was something that bothered me .. so i think ill give it a go once my scooter arrives xD oh and thanks for the sweets you sent with the charger ports lol ah yes the grit tape looks great i guess i will order that also thank you . keep up the great work
@proxyhx2075
4 жыл бұрын
Man the noise coming from the tires are so good! It sounds like a motorcycle!!
@joshuasticky
4 жыл бұрын
100% you have more control and safer with finger control. All the big boys say the same thing. Ive used both for many years.
@davidmichael3189
3 жыл бұрын
I agree with what you say about the thumb throttle. At least I am not alone in thinking the thumb throttle is safer. Many thanks.
@alanhold2468
4 жыл бұрын
Those locking gripps look so much better. I was looking at the same ones on eBay. And the ztto grips. Nice work brother👊
@Busa0069
4 жыл бұрын
They should build them all with thumb throttle and swap the brake levers around so front brake is on the right side like a road motor scooter.
@yeahbuddy6852
2 жыл бұрын
On janobike t85 has rear break on left side....
@IIISentorIII
4 жыл бұрын
HAHA "Angry Dog" :), the sandpaper picture reminds me of prinzessin mononoke ore the last unicorn art style which i always liked. I always smile when you say "full throttle" it's such a typical Pirate expression :). Did you had time to check the battery range yet, what do you think how many km you can make with Dual motor and ~25-30 km speed. And btw, very nice work with this thumb throttle MOD! Cheers
@PirateWasHere
4 жыл бұрын
About 40-50km 🚀🍻🏴☠️
@IIISentorIII
4 жыл бұрын
@@PirateWasHere Awesome, thanks
@The_RSathya8
4 жыл бұрын
Great man ! ..You did a perfect job on it!! Def I believe that throttle is a lot safer. I’ll get my scooter in a few weeks and would like to install it. However, I have not any skill about soldering. I have no idea who could help me with that .. maybe u could visit Amsterdam?! 😃
@808pathfinder
3 жыл бұрын
i just got one and i found what i was looking for , I love your channel ,best one in my book. I hit the like on all your vids for support ,cant wait to upgrade the mods you should us for this type of escooter
@charleslebon4583
3 жыл бұрын
Merci pour toutes Tai vidéo je viens de l'acheter et tu m'aide beaucoup pour l'améliorer !!
Жыл бұрын
Thanks so much for this, I can now use my scooter again 😁
@Azyune
2 жыл бұрын
Ok good point, now you did convince me to do this mod too, thanks for the instruction.😉
@PirateWasHere
2 жыл бұрын
what about this ;) kzitem.info/news/bejne/w6aAuKSebophdKg
@S0RREN
4 жыл бұрын
Thanks Pirate. I’ve been wanting to order Boyueda for quite some time. After your reviews its a no brainer. I am definitely keen on the throttle. How about twist throttle? Would it be also easy to install? Would you recommend based on your experience? Big cheers from Czech Republic here.
@majintks
4 жыл бұрын
5:40 the sound that the suspension makes, does it when it spreads or when it contracts? Thank :)
@Bornmong
2 жыл бұрын
Would love a video for dummies like me.
@tindalowos
4 жыл бұрын
i basically ride with my index fingers pointing forward, one for rear brake one for throttle
@netpa6231
3 жыл бұрын
Nice video!!!! Thank you for help!
@les1669
4 жыл бұрын
If I had place's like you have to ride I be Rolling. I live in Hawaii u would think? not a chance. I got me a xiaomi pro due to your video reviews a month ago and enjoying the ride worth the $ thanks .
@angelozucco6152
4 жыл бұрын
You shoul try to a twist throttle instead. I chose that and I can assure you that t It is much safer and gives you much better control. The electronic modification is identical.
@jose-emanuelgoossens3050
2 жыл бұрын
twist throttle in my opinion is only good if u use a seat on your scooter
@verbsy
4 жыл бұрын
Hiya Pirate any chance of you doing a 'All P Settings video' in the near future ? or perhaps a link to one that will compatible with the 'Laotie ES18' many thx
@tnunited2436
3 жыл бұрын
Can dualtron eye3 can convert also to this thumb throttle?
@nitrobitde2609
3 жыл бұрын
Would you recommend buying a Laotie ES18 or a Boyueda? I want to ride both street and off-road, but most of the time road. What are the pros and cons between these two?
@strawman9410
4 жыл бұрын
Hello Pirate thanks for your videos very interesting and sometimes funny. I ordered the thumb throttle like you suggested X108 because I do prefer a thumb throttle out of the different types available finger pull, wrist twist and thumb. But mine has no hall sensor on it. It has a push on Waterproof connector, which I have already cut off. The question I have is, is the connection to the LH100 board any different? I don't want to cut the pins off the hall sensor that is already on the board unless absolutely necessary?
@dixaras
3 жыл бұрын
Is there a way to have both throttles working? You are a info`s treasure man. Thanks
@PirateWasHere
3 жыл бұрын
it could be possible but you need to make electronic circuit which separates signals or by easy way add simple switch for every signal output to choose which gimbal you would liek to use and just turn it on by switch.
@topcat8820
3 жыл бұрын
I’m baffled by that switch of camera angle ... How is it flipped so far away from your face without a spinny go pro mount
@josefbartak6556
3 жыл бұрын
Hi, I did everything in accordance with this manual, ordered the thumb throttle from the link, cut off the hall sensor and soldered the three wires in a correct way. But now when I turn on the LH-100, I am getting Error 08 - Throttle error. Any ideas why and how to resolve? Thank you
@marmellus
3 жыл бұрын
Do you know if there is any kind of a portable "power station" to charge our Escooter if we need power to get home ?? :)
@tupalyoutube2902
4 жыл бұрын
Kiedy odcinek z laotie es18 ?
@DriveSimulation4K
3 жыл бұрын
Hello I upgraded by removing the sensor, but I have a problem. When I accelerate more than 50% the scooter stops accelerating and activates the engine brake by activating the stop lights. What could be the problem? For now I solved it by disconnecting the engine brake cable. Thanks for your help.
@newinsight
Жыл бұрын
Thumb throttle way better. I broke my wrist because I accidentally grabbed the front brake instead of throttle because they are so close to each other. Yes I'm unco, but the design didn't help.
@seant10115
2 жыл бұрын
How long did it take for this scooter to come from china
@marmellus
3 жыл бұрын
We are waiting for our review on the new Laotie ES19 ;)
@PirateWasHere
3 жыл бұрын
Working on it!
@maxzzetron
4 жыл бұрын
Hi Pirate. How does this throttle trigger compare to Xiaomi? I some time think to replace throttle trigger on Xiaomi m365 to this device. Is there any reason?
@jameswilson2904
2 жыл бұрын
For me, this thumb it's too long and has a huge deadzone. I did see a video where someone made it shorter and modified the magnet for a smaller deadzone if that makes sense. I need to find this video
@antonypartali
3 жыл бұрын
I change the throttle from finger to thumb like your way!! Flj 2400w 52v The scooter is working, it starts more aggressive (that's good) BUT it stops to 50 klm!!!!!! 😠😞😞 I have see 70klm with full battery 58.8v💪 What's the problem...??? Das it have to do with the new throttle...??? 🤔🤔 I buy it for China the classic one that is throttle and voltage meter!! And write that works from 12-84v!! What the problem...??? I was so happy when I see that works aand now.....😓😓😩😫😫 PLEASE help!!! 🙏🙏🙏
@tramelulysses4327
3 жыл бұрын
Why not do a video on Setting up the throttle ?
@808pathfinder
3 жыл бұрын
how much air do you put in the front and back one?
@TheChazas
4 жыл бұрын
What kind of Helmet you rock?
@MrGiodude17
2 жыл бұрын
Where is the link so I can do it at home myself
@Guilourenco1
3 жыл бұрын
My Smartgyro Speedway v2 800w as thumb throtle and is not progressive. Its like on/off especialy with level 3 that give max power :(
@quadrometer
2 жыл бұрын
Hey Pirate, now i have a question i hope you can answer. I also would like to install thump trottle at my talotie ti30. But there is no connector to disconnect the lcd display. It looks it is connectet direktly in the deck. What do you think will i have a hall sensor in the origanal trottle and shoult i risk to upgrade without disconnect the original trottle??
@PirateWasHere
2 жыл бұрын
you do some soldering job m links in description
@zielonakosa
3 жыл бұрын
Piracie ja chyba czegos nie rozumiem. Po co zostawiac stary hall sensor z wlutowana jedna noga? Rownie dobrze mogloby go nie byc bo jak ma polaczenie tylko jednym wasem to on nie dziala? Mozesz wyjasnic?
@PirateWasHere
3 жыл бұрын
Jest ustawiony na odpowiednia dlugosc, latwiej wrocic do stocku
@zielonakosa
3 жыл бұрын
@@PirateWasHere w laotie ti30 zmienilem manetke na kciukowa i jest podobnie czyli dalej bardzo ciezko plynnie regulowac gaz. W trybie eco jest ok.
@PirateWasHere
3 жыл бұрын
Jak bys chcial super plynnie to zostaje wymiana kontrolerow na vesc , niedlugo zrobie film
@ukasz6000
4 жыл бұрын
Cześć Pirate , jaka hulajnogę polecasz i skąd zamówić z bezproblemową dostawą do Polski ? maksymalnie do 6 tys złotych ?. Obecnie mam xiaomi m365 pro ale chciałbym w przyszłości zmienić na cos mocniejszego z pełną amortyzacja ( jazda po lesie ). Drugie pytanko jak z softem 800w do m365 pro czy długo jeździłeś na takim ? Jakieś problemy zauważyłeś ?. Obecnie mam tylko odblokowana prędkość i leci maks 33 przy mojej wadze 109kg. Dzięki za odpowiedź.
@PirateWasHere
4 жыл бұрын
Bierz T85 albo mojego Fav es18 🍻🚀. Nie wiem jaki soft 800w do pro, bo stock pro w peaku ma 1000w xD
@paweljeziorowski3837
4 жыл бұрын
Pisalem do softu na banggood odnoscie t85 no zmieniły sie aukcje jak i t85 i tego co teraz ma pirate w t85 juz nie ma bateri 21700 tylko są już 18650 a w tym co teraz ma pirate slabszy kontroler i silnik slabszy wzamian za baterie 28.6 ah
@PirateWasHere
4 жыл бұрын
20700 stara bateria miala 32ah ;)
@paweljeziorowski3837
4 жыл бұрын
@@PirateWasHere jak przegladalem predzej bylo 26.2 ah dokladniej miesiac temu dziwne robią wałek zdecydowalem sie na es18 ma migacze i amorki normalne dają tylko czy bedzie smigać rownie dobrze 😛
@PirateWasHere
4 жыл бұрын
Tak , wlasnie te niby 26.8 mialy 32
@Falcon00000
2 жыл бұрын
Da się kupić taki dywanik na podest w Polsce?
@PirateWasHere
2 жыл бұрын
Dywanik 🤣🤣🤣🍻
@qwinzy4193
4 жыл бұрын
do you recomend the BOYUEDA or JANOBIKE T85 for top speed ?
@PirateWasHere
4 жыл бұрын
T85
@qwinzy4193
4 жыл бұрын
@@PirateWasHere what's the reason for that?
@PirateWasHere
4 жыл бұрын
Because i like multipurpose, if u like power then boyed
@qwinzy4193
4 жыл бұрын
@@PirateWasHere ok but the janobike t85 has higher top speed than the boyueda?
@PirateWasHere
4 жыл бұрын
Yes 🚀
@sammyould-brahim7327
3 жыл бұрын
hello, how many kilometers can you cover with this scooter ??
@PirateWasHere
3 жыл бұрын
20-55
@sammyould-brahim7327
3 жыл бұрын
Pirate ok maximum 55 ?
@antonypartali
3 жыл бұрын
Hi my friend! It just came my new display (damao) and of course i open it and make it thumb throttle ( i have already done that i have on scoot)! The new thumb throttle is like yours! My problem is that the new throttle don't respond so quickly... Why? First i have to tell you that i but display left side and thumb throttle right side (the wire is 40-50cm) is there a chance tothat is the problem?? Is the display?? Or something with wires,.. I say about wires because when touch white (green) wire (without ground only touch) motors going to spin...😲🤔 My old thumb throttle don't work... Only This one like yours... What s the problem????🤷 It crazy me 2 days...!!!!😤😠
@PirateWasHere
3 жыл бұрын
If u got throttle latency then this is progammed into controller.
@antonypartali
3 жыл бұрын
@@PirateWasHere so the problem is from controller?? Because and the controllers are new!!! Can i fix???
@PirateWasHere
3 жыл бұрын
Well if it has the same tiny latency like boyeda has then this is normal
@antonypartali
3 жыл бұрын
@@PirateWasHere i get used the first one that i do ( it was like a spark) and the new One looks like old train... And the controllers are bigger...☹️ Anyway I have a video with the parts as it cames to me, but if i can't do anything i have to use to it...!! Thanks for your help Bro!!💯🥰
Пікірлер: 90