Visit our website for more information: tigertool.com/products/commercial-u-joint-puller
@terrellscaife2411
3 жыл бұрын
This could be the greatest KZitem video ever made
@taylorculley2461
7 жыл бұрын
ive only had to use this tool once but when you need it,its worth every penny
@lazarollanes5228
2 жыл бұрын
Thank you so much, this is video really helped me
@SignatureStampsFan
8 жыл бұрын
I love this tool.
@jessetoptechallen1461
8 жыл бұрын
good tool
@dormindont1
10 жыл бұрын
Отличная приспособа!
@ScottDLR
3 жыл бұрын
I dont know about the tool itself but your video is sure better than "OEM's" poor attempt.
@geoffclark9820
7 жыл бұрын
On full mechanical u-joints it's a must! In Canada the salt in the winter will seize it solid. He keeps the impact going like a moron, I run it up tight and smack the ear. That way you don't wreck the yoke or ear on the drive shaft. I have to say though, the tiger tool kingpin press tool is a bag of shit. I paid $1600 for mine at Gregg Distributors. Works fine if the kingpin is sicky but if it's seized into the axle it doesn't work at all which makes it absolutely useless. For $1600, it should work on everything!
@shortthrow50
6 жыл бұрын
Geoff Clark nobody else that I know has such problems with their u joint and kingpin removal. In the United States we own grease guns
@mschelleman925
6 жыл бұрын
Hey cockwad we have grease guns up here too. We also have licensed mechanics. something you guys should look into
@mandoky1647
3 ай бұрын
Until the threads strip out on the tool.
@cliffordshaw3032
4 жыл бұрын
I love this tool , how much it cost
@ryansmithberger3140
11 жыл бұрын
is there a smaller version for the auto industry
@thebad300
8 жыл бұрын
yes but does not look the same look up ball joint/ujoint press www.amazon.com/OTC-7249-U-Joint-Anchor-Service/dp/B0002SRGXY
@mirocabraja5128
7 жыл бұрын
Wddddddfdd
@TrentBigW
Жыл бұрын
I drive a wrecker. We have to pull and hang the driveshafts, and we dont actually pull the u joint. We just seperate it from the yoke. Do do i just need to pull the two? Or do i still need to pull all four caps?
@TigerTool
Жыл бұрын
You can just remove the 2 caps on the one side.
@TrentBigW
Жыл бұрын
Thanks so much
@TaintedMojo
3 жыл бұрын
Is it actually designed to be used with an impact gun?
Andrew Wilson I seen one, not two. It's got some caked grease on the bearings too.
@Mr1968gtx
11 жыл бұрын
Tiger Tool part # 10105 or 10104
@shawclifford5332
4 жыл бұрын
Where can i get that tool to buy
@BACONNWRAPPED
4 жыл бұрын
amazon
@ThrottleJerk
9 жыл бұрын
You shouldn't be using an impact on a puller, it's very dangerous. If the joint is stuck, you accumulate energy in it qnd when it unstucks, the puller or joint could break and cause serious injury
@thebad300
8 жыл бұрын
+Gabriel Thériault as long as you are not a dumbass and use the correct lube on the screw its not an issue
@LP2Check
6 жыл бұрын
When it unstucks....when it breaks free. Real fine work ya pus
@familytraditiontransportat7951
Жыл бұрын
Pretty sure the maker of the tool knows how best to use it... But hey if you want to use a ratchet by all means go ahead Popeye.
@ThrottleJerk
Жыл бұрын
@@familytraditiontransportat7951 damn i was dumb 7 years ago
@envisionCamusa
Жыл бұрын
@@ThrottleJerk I respect people that learn and admit to things.
Пікірлер: 36