Ok...gotta confess...Ive heard about this spring thing before and refused to believe one little spring could cause all this trouble and frustration. Blamed the tobacco...blamed the tubes...blamed the humidity..blamed there wasnt enough humidity...then figured it only happens on days that end in y. Well today I tried something really out of character for me. I just broke down and took somebody elses advice and went to Ace Hardware and bought the frikin spring. Cost a whole $1.19. Took 2 whole minutes to change it. Now all the people in my house are no longer in fear over my anger and swearing...even the dog looks relaxed now! And the best part...I now have cigarettes that are as good as any factory made ones again! So quit having nervous breakdowns and just take toms advice...Just go buy the damn spring! Thanks Tom!!😀 BTW...stick a slice of bread in your tobacco bag...keeps it nice and fresh! Really...just do it.
@billiepierce5810
4 жыл бұрын
break absolutely works! Even when your tobacco is dry as fall leaves. Going to get a spring now.
@billiepierce5810
4 жыл бұрын
bread lol
@ihavefallenandicantreachmy2113
4 жыл бұрын
Will a Bagel work? A Baguette, perhaps, in the Bag. Seems fitting.
@Warlanda
4 жыл бұрын
@Ozzy lol! what a great comment!
@italiangirl2789
4 жыл бұрын
LMAO I'm so happy I read this feed and saw your comment bcuz my poor husband and cat live in fear bcuz of this friggin machine!! LOL I laughed so hard, thank you for that😘
@toriguetzke-hl1lp
Жыл бұрын
You just saved me so much aggravation! I never thought to check spring since it wasn't broken. Thank you, I was ready to buy a whole new machine.
@jakequake8689
4 жыл бұрын
Thanks for the video and inspiration! I had the same problem. But I found another solution which might help, too. After watching this, I saved myself a couple bucks and a trip to the hardware store by reworking the native spring by increasing tension. Using strong small tweezers, I unhooked the spring on the static end, and then wound it up at the moving end a few turns, then attached it back on the static end. Works perfectly, no more misfirings!
@michelleduncan5919
Жыл бұрын
This is great advice. My friend gave me mine used and I really love it. It's much quicker than the little handheld machine. A couple other causes I've noticed in the machine stuffing them half full....packing the tobacco too tightly, the arm not being screwed on tight enough (my screw loosens a bit with each rolled cigarette), and the rubber piece that holds the tube in place slides up so its unable to keep the tube in place. In fact. I lost the original rubber piece and was about to order replacement like 2pk for $10. I got an idea....the rubber tip off earbuds! Been using the same one for like 2 years. Plus they're free
@Bonjour-World
9 ай бұрын
I used heat shrink tubing
@mickbarrett4777
2 жыл бұрын
Bro...I know I ain't the first to say it, but thank you. You just saved me $300 on a new TV. (Because the last time my top-o-matic fucked up, I nearly threw it into my television)
@Hermitcrab2004
Ай бұрын
you can try us the newist one
@greggrobinson5116
4 жыл бұрын
Another thing you can try: The moisture of the tobacco is a critical variable that's too often ignored. Too moist and it won't burn well. Too dry and it'll crumble and produce fines that won't pack well. So try the old pipe-smoker's trick of throwing a wedge of apple or a damp (& rung out) paper towel into your tobacco stash to keep it at optimal humidity. This is what works for me.
@laragreene8328
3 жыл бұрын
Nope, mine is too moist. I add nothing.
@renerenatorivera9062
2 жыл бұрын
Exactly what I've been doing for years. It also allows me to user the whole contents of the tobacco bag. Previously, i woul wind up with a bunch of too dry stuff that was unusable ( a waste of money).
@renerenatorivera9062
2 жыл бұрын
where can I get that spring?
@yashamaga13
Жыл бұрын
@@renerenatorivera9062 ace hardware, probably home depot, lowes
@chrisw5742
Жыл бұрын
What I found to add the perfect amount of moisture back into the tobacco is to blow through it a few times. I put the tobacco to the side of a container to do it. Make it roll perfect again. I have tried a moisture pack and that got it too wet.
@adorabledeplorble8497
Ай бұрын
Thanks for this, four years and you are still helping folks! The comments are great too!! I am headed to find a 119 and a small oil can, but that’s fine I needed a tobacco run anyhow since my easy little store is out of the stuff I wanted, and my sewing machine could use some oil anyhow. If I see heat shrink or ear buds I might make a new rubber bumper too because mine has a few divits from trying to hold the tube on strategically with my thumb and maybe pressing too hard, or getting a little tobacco stuck there during a lot of rolling… then I flipped the bumper over 180 and made a whole new divit (My bumper is now on a 45 degree spot and this game cannot continue forever). My only issue is, how do I drive to Ace without rolling more dangerous “fall off in your lap” half cig’s for the trip? Much appreciated Tom 😎
@JoyAZrebiec
4 жыл бұрын
Will try. I've been going CRAZY with the half filled tubes. 🤬 and we also tried different tubes, tobacco...cleaning it, etc. Thank you for sharing!!!
@number1pappy
2 жыл бұрын
Thanks for the video! I was seriously skeptical but I went ahead and went to my local ace hardware store and picked up 3 119 springs. I took em hime and installed one in my machine and I also lubricated it with some 3in1 oil I have. All I can say I'd thank you so much! My machine works just like day one! I also put one of the new springs I got into an older one I had that stopped working over a year ago. It worked on that one too! Now I have two "T2s" that work just fine 🙂
@heitmanga
3 жыл бұрын
So, I didn’t want to believe that the fix for this was that simple. But, it was ! I have been rolling for about 2.5 years and every six months, the issue of underfilled tubes would creep up. My first machine, I ordered parts recommended by another roller and replaced them but never thought about the springs ... in any case, this didn’t work and really, a new machine every six months meant I was still saving a ton of money not buying smokes. Today, almost ordered another new machine, but read this and I just returned from the hardware store with four “119” springs, 1.75$ apiece. In about 30 minutes, I replaced and tested three “broken” machines, so now I have two refurbs “just in case”. Thanks, Tom, for the fix. I will also add that the humidity of the tobacco can cause an occasional issue, but this might be 1 in 30+ tubes and after so long, I can almost feel the issue before it happens ;) a piece of bread in the tobacco bag works, as do the little cigar humidifiers (size of a few stacked nickels), but don’t overdo it or the tobacco starts to stick and jam. Reading other advice here, I also saved the old springs, and will try the advice of reusing them by trimming these a bit, next time the need arises.
@chelseavidika9954
Жыл бұрын
My machine has 2 springs,1 on each end. One is short oneis longer.Does the longer one also need replaced?
@JaiSriAstrology
15 күн бұрын
You were right, tried pressing on the rubber arm to add a bit more tension during the fill and found it was releasing the tube too early causing it not to fill correctly. You were right on the money, it is the spring tension. Thanks Bro.
@had2galsinthebooth
Жыл бұрын
After buying like 4 Topomatics I gave up trying to adjust things or mess with springs. On this 5th machine I just push my left thumb lightly against the rubber titt to help it hold the tube on until it is full. This 5th machine has lasted me around 5 years,maybe longer,I don't remember. My method does put the left thumb in danger but I haven't jabbed it yet. It also rips a tiny chunk of paper off the end of the tube but that's no problem at all,into the pack they go and smoke just fine. I also took one of the silver handles from and extra machine,drilled another hole in the crank handle,and fitted the handle to the crank after tossing the stupid knob in the trash. The handle mod gives me lots more power when the tobacco is damp due to humidity. I don't use air-con,just several fans,to keep cool,so high humidity could make stuffing smokes a real pain in summer but not anymore. Been stuffing since 2009 when the IDIOTIC fire safe cig law was enacted, that crap made me sick so I found a way around it.
@morgainnejade
3 ай бұрын
I was introduced to rolling your own around '97 or '98, & had been smoking strictly American Spirit for some years prior to that. And I used their brand of tobacco in the days before the price ran up to near gold price levels. By the aughts I found that smoking more than a couple of pre-mades in a row made my throat very sore & start to feel like a first tickle of catching a cold, & already back then it made me feel that if I had to choose between only smoking pre-made or not at all, I'd quit in a heartbeat. These days pre-made cigarettes resemble tobacco about as much as Crapdonald's resembles a food-like-substance. I laugh (to myself) when people think they are being kind & doing me a favor by offering me "real" (pre-made) cigarettes. Camels in all their varieties & flavors are still pretty good though, in a pinch.
@had2galsinthebooth
3 ай бұрын
@@morgainnejade My dad had a cig rolling machine in the 1960s but instead of stuffing a tube it actually rolled paper and tobacco up and over the top dropping an unfiltered cig out the other side. I used to ask to roll them but it was rare he agreed,I suppose at such a young age I was too slow and would mess up.
@gailcallicoat1412
3 ай бұрын
I want to thank you so much for the info on getting a smaller spring. It works perfectly. Thank you again😊
@jolindasloangiessel9616
7 ай бұрын
Thank you so much! I have been trying everything. Narrowed it to the rubbber thing. Even taped sandpaper around it for better grip. I am on my way to get a spring! You are very good at explaining things.
@fredvondra
3 жыл бұрын
The #119 spring was $1.39 at my local ACE Hardware. Very easy to find. I bought an extra one for backup. Thank you Mr. King!
@Sari749
2 жыл бұрын
Looking for the spring, do you have a skew number. Ican't find it
@fredvondra
2 жыл бұрын
@@Sari749 I don’t. But the hardware store is a block away. I will go down and look. But, like all ACE hardware stores, they typically do not have skew numbers for singleton small screws and springs. If you post your email address I will send you a picture of the drawer they are in and related identifying information.
@fredvondra
2 жыл бұрын
@@Sari749 540356 Ace Hardware.
@number1pappy
2 жыл бұрын
Yeah, I paid $1.89 for mine! I'm guessing inflation! Lol!
@joevasko6004
3 жыл бұрын
In the past I threw out 2 machines! Thanks for the advice.... Never get rid of an old Top O Matic machine again...Life Saver...
@the-papaw
3 жыл бұрын
Thx for the video, if you don't have a replacement spring, you can also just cut off a a couple winds of the spring from one end
@rosumell3421
3 жыл бұрын
Hey Tom, Been having prob's with half filled tubes like many others here. Yup, looked at machine too when started malfunctioning. Thought might be rubber bumper or one of the springs, tobacco, tubes ect. Wetting and wiping bumper helps. But, after watching your video and getting worn out from redoing half filled tubes? Tried your solution of new spring had on hand and reoiled machine. ( Used sewing machine oil, doesn't have that oily taste.) Ummm, your solution doesn't work too good, it works great! Thanks for great fix, is appreciated!
@hollyinhell
Жыл бұрын
I don't even smoke anymore, but I remember this always being an issue so I wanted to see what the solution was. Very interesting and informative video.
@johnpearson4899
2 жыл бұрын
Got one just like that. Bought on valentines day 2012. Learned right away to remove the adapter for king (regular) size tubes. Worked fine for 12 year on nearly any cut of tobacco with a wide range of humidity content. Most tube brands worked well. I've use Zen tubes mostly. About a week ago it start pushing, and sometimes tearing the tubes off without filling them more than half the length. Seems the tobacco wants to bunch up as the arm is turned. The machine hasn't been dropped. In fact it hasn't been moved from its spot for about a week before it stopped working. I clean it every 2 - 3 weeks whether needed or not just to keep it inspected. I did try another brand (Gambler) tubes and they really didn't work much better, if any. Maybe time for a complete rebuild or, I may just trash it and buy a new one.
@Luigi110067
2 жыл бұрын
I knew the problem with mine was the arm that pinches the tube was not strong enough I just didn’t know how to fix it. Thank You
@brianjohns7608
2 жыл бұрын
Thank you so much! Could not figure out why I was only filling up halfway I mean it's a brand new machine should work thanks again I do appreciate your time have a great day
@LorneVignettes
Жыл бұрын
I think the regular TopOmatic machine is better than the T-2. I had the T-2 First and then I bought the original TopOmatic and I really like it better. I'm about to post a video comparing the TopOmatic to the Powermatic2.
@marcussteinhauer4652
Жыл бұрын
Thanks for figuring that out. A new 119 spring did the trick. Working great now. Oil helps too.😃
@gorillahumpr
3 жыл бұрын
Thanks for the info. Till I fix it I realized I could put a bit of pressure on the rubber holder and it works great
@nmHispana
3 жыл бұрын
This summer I tried using that 119 spring from ACE on a Top O Matic that started doing this within less than eight months from it's date of purchase and it only worked for a while. Therefore decided to purchase the T2 instead, however less than five months (since purchase) and it too has also started doing the same thing. I have found a solution that's been working for me and that's to first make sure each corner is packed with tobacco and then instead of pulling the handle all the way, it's pulled down slowly and stopped when the click is heard, then slowly pulled down again to finish filling the tube.
@shawnwade302
2 жыл бұрын
Thank you thank you thank you!!! I wanted to throw my T2 through the window! I make 100's but had the same problem. A couple hours ago it was having this problem 3 out of 4 cigarettes I made. Saw this video and ran to the hardware store and bought the only two 119 springs they had. I had to stretch the new spring just a little bit because it was biting a little bit of the tube off when making the cigarette. One little stretch and its still stiffer than factory spring and my problem has disappeared. Thanks again.
@Joel-qm1yc
15 күн бұрын
Thank you! Having this exact problem after rolling my first 500 or so cigs. Heading up to ace to grab some of these now!
@dorelteodorescu129
Жыл бұрын
Thanks for the clip and all the comments! I am using a similar version of this o-matic and mine just needed lubrication for now.
@rogerhislip5269
2 жыл бұрын
I shortened up the spring by 1/3 and it’s like new. Thank you!
@hollyarabie8369
11 ай бұрын
YOU ARE THE BOMB TOM!!! Thank you so much dude. I was just about to throw this thing into the busiest traffic!
@joniforsyth5709
Жыл бұрын
Thank you that's very good advice that I'm going to try I've been rolling a long time I just saw that I might tell you all that regular tobacco people tend to buy like 1839 I think the name of it it's long and you know hard to roll I found a brand that is tube cut it works so much better in the rolling machines it doesn't jam up. I hope that helps and now I'm off to the hardware store to get me a new spring. Thank you for sharing
@handotz
Ай бұрын
So. This fucking fix is the way. Holy shit. Rolling better than new. TBH the new spring (119 at ace hardware) took a little getting used to. I had a lotta ripped cigarettes at first. Not more than i was rolling, but enough to make me question it. I didn’t have the oil he had, i used canola oil. Also the nut on the crank started to come loose and id rip cigarettes. I was a little annoyed. But i kept with it. I rolled 300+ today (going on vacation soon) and i had two fuck ups total. This is it. This literally is it. Use WD40 if you want, but it works and its better. I also use a scale and weigh my tobacco to .9 gram fwiw. Thank you OP!
@Dave_McKansas
Жыл бұрын
Good comments in here. Thanks to everyone. Another quick fix is 2 layers of Electrical Tape on the rubber bit. Not permanent, to be sure, And thanks for identifying the problem.
@OhioBoii330
7 ай бұрын
Soo, i have a similar roller. Same brand and probably the same model. Mines just orange and not silver. But, my little rubber piece is in fact kinda damaged. But, i just hold it with my thumb and still have the same issue. OCCASIONALLY i can get a full tube, but its pretty loose and needs severe packing. Soo, im gunna have to assume that it is the spring and im gunna replace it!! All the comments agree with the video, so hopefully it solves my problem! Thank you!!
@shawnfisher4710
3 жыл бұрын
They all do that ,spring is the way to go ,good job letting people know .I just bought this model last week 57.99
@uniontank7125
5 ай бұрын
Wrap some good tape around the neoprene/rubber sleeve. It will temporarily help dog the tip of the tube off tighter until you fix the underlying problem. It enlarges the diameter of the sleeve. Another thing I do is hold the sleeve tight with my pinky while cranking the handle.
@fatdrunkbaby24
Жыл бұрын
Nice tip, thanks. Heres one back: I keep my machine in an upside down shoebox. The lid doesn't impede action of rolling and keeps the tobacco contained. When finished, use the box as the lid and store it on a shelf.
@frankiethebull8269
3 жыл бұрын
Great advice definitely going to try this too, I wish they(Topomatic) included a troubleshooting pamphlet with the machine as well. I found rotating the rubber bumper/holder after a dozen or so cigarettes helps as well. Because it does get a crease in it possibly causing friction loss.
@bluzeblast
2 жыл бұрын
Yeah great suggestion! I'm using the same machine and had the same problem with the half full tube. I found that if I took my little finger and pressed the hold post that solved my problem. Your idea is a much better solution. I also use sewing machine oil on my pivot points, and you gotta be careful and not get it where it saturates your tobacco and tubes! LOL how do I know that? I dont wish to own an electric machine because if the electricity is out I wouldn't be able to make smokes. Also, when I clean my machine, I do it in the kitchen sink....
@immaggiethesenilegoldenret7918
4 жыл бұрын
Thanks so much! I got a cheaper version of the “Top-O-Matic” from Amazon and this keeps happening!! Going to try to get the spring today!
@jt.s.7418
2 жыл бұрын
Great tip. I twisted the spring a couple of times and what a difference. Thank you!
@sherrylowman3362
4 жыл бұрын
Thx I've been fighting this issue since day one.
@ruthann4534
Ай бұрын
Thanks for saving my sanity. I’ll get a spring and try it
@davidcudlip6587
11 ай бұрын
You can also bend the little arm a wee bit (with needle nose pliers), that holds the cigarette tube in place till it just releases when the packing rod is extended all the way out. It will keep the tubes on till the they are all the way full. Agree the stock springs should be updated. Wonder how many people throw the machine out when they could have easily fixed it.
@avenqer
3 жыл бұрын
To check to see if this is the culprit, here is how I tried. Mind you, I have had a 9 in 10 half fill UNLESS I underload it. So what I did was once the handle goes to the first setting, I push on the rubber with my left thumb against the injector nozzle then pull the handle. Injects perfectly. 4 in a row. Just wanted to share. UPDATE: Rolled 2 cartons, only 2 ended up half full with this technique. Saves me running all the way to town hoping to find a spring or a new unit.
@rlux70
Жыл бұрын
This comment is underrated. There's no need to replace the spring unless you want to. Just set your finger on the black rubber piece while injecting.
@kimgroat1199
4 жыл бұрын
Replacing the spring worked!!! Thank you! Go get you #119 spring!
@HillshaveIsaac
4 жыл бұрын
What is a 119 spring?
@joniforsyth5709
Жыл бұрын
Thank you for sharing I'm having the same problem and I was about ready to go buy a new machine so I'll just go get a new spring and see what happens thank you very much
@jacobclements1582
2 жыл бұрын
I hope my dearly beloved doesn't run into this problem I checked this video out for future knowledge you are the messiah
@GodlessManitoban
3 жыл бұрын
Great video, it showed the underside of the machine and how to fix the tube clamp issue. I just ordered a T2 limited edition in blue. I'm tired of those cheap plastic machines. Also I'm glad you didn't use WD40 like some online search results recommended.
@dean3434
3 жыл бұрын
Had the same problem until started using Top tubes. Like magic, getting the full-fill in the Top tubes 99.9 % of the time. Dean Seattle
@chrisl.8990
2 жыл бұрын
I agree that it's the tubes. When I use Beretta tubes I never have this issue. They cost a bit more but the consistency of the diameter of the tubes is much better.
@jayjayshorts3102
Жыл бұрын
Thanks I’m gonna try soon as I can been trying to fix this on my parents and I T2 forever hope it works
@creamycream3587
11 ай бұрын
When you start having the same problems Again, it the rubber waring out, I actually stopped rolling with a Machine and started rolling up by hand for several years. Because i was going through 4 top o magic machines a year. I'm gonna try the Powermatic manual now. Everybody says they are built better
@chefmarcg
2 жыл бұрын
using the oil is a bad idea....it causes the fine powder tobacco to gunk up the machine and make you have to clean it a lot more often...ive found its best to just use a pencil or a piece of graphite and put a fine coat over any of the surfaces that rub up against each other. i hope this helps
@ittakesallkinds809
10 ай бұрын
Thanks so much for your video! My problem is exactly as you described.
@BirkinIdk
3 жыл бұрын
Haha I just have to say, as someone that works in a spring factory it's insane to hear they're charging you a whole dollar for one spring! For reference, our absolutely highest paying customer (St. Jude Medical) pays $5 per spring that is designed to operate an artificial heart valve. We'd probably sell the spring you have to a customer for like $0.08 or even less lol.
@combatgirl38
Жыл бұрын
I was thinking the same thing! I took a quick guess at 20¢ before he gave the actual cost and I was just appalled! It's like they're trying to force out any type of fix it yourselves type solution by making the endeavor so unaffordable that it's not worth it to extend the life of what you have so that buying a new one becomes a relief. It's gross. I have probably about 100 lbs of random hardware and Maybe 2% of it I've sought out and paid for. The rest I've literally alley scored and dumpster dived. I guarantee I have this spring Somewhere. It's Crazy how much gets thrown away into tearoff dumpsters as well!! Anyway, thanks for pointing that out!
@sherrylowman3362
4 жыл бұрын
We have all experienced the same issue. I'm contacting the company
@sherrylowman3362
3 жыл бұрын
@546 cowboy Where is your post?
@nathankindle282
Жыл бұрын
Thanks for the advice. Gonna have to make a trip to Ace Hardware now
@philwilliams6873
Жыл бұрын
Thank you. Works perfectly now! I was ready to sledgehammer the damn thing. Cheers!
@karenreece4017
Жыл бұрын
Hey thanks I've been having the same problem too now I know' we t Google search found your video will give it a try thank again 😊 😀 Karen
@davidjhartt
2 жыл бұрын
my issue was the same but wasn't the spring. The rubber piece was riding up on the post it was on. Pushing it down fixed it.
@doctorPcP
6 ай бұрын
Gracias 👍👍, exactamente ese era mi problema y gracias a Usted lo he solucionado
@RustyYorkThievery
6 ай бұрын
Thanks! replaced both springs.
@danielburns7519
4 жыл бұрын
thanks for the fix.my t2 was in need lubrication in the injector as it was sticking and the spring was too weak to hold the tubes.
@josephbeattie5525
3 жыл бұрын
Thanks! I put a little heavier spring on there and it works better than new now
@cprpottsville
Жыл бұрын
Thank you Sir! I've been Peedoff for weeks!
@sarabatton6700
3 жыл бұрын
thanks for the tip....but at my local hardware, it was not called a 119 spring, so good thing i took the old one and for $1 got a new one
@melvinc.huskey5828
3 жыл бұрын
Hey guys, I found that if u dont push tobacco under the front corner,& just keep it in square chamber, u will not have space between filter & tube. Hope this helps u all. Gd luck to all.
@ToxicityLimits
Жыл бұрын
Thanks for this video and the information details about the spring
@tattoosbybigchris8570
2 жыл бұрын
Yep! That was the conclusion I came to as well. Factory spring is just too weak.
@TheDigitalThreat
2 жыл бұрын
The blade/tamper dulls very fast and after so many cartons it just becomes junk leading to non stop jams as it can no longer cut as you inject. To replace that alone cost 8$+ shipping which is roughly 1/2 - 1/3 the price of these units at base cost. The T2 is the same exact machine as the standard, just with chome/bling appearance. They are no stronger than the others, and just cost an extra 10-15$ for said bling. Its not even worth repairing your own tamper/blade aside from the cost because you then need to then put it back together which isnt an easy task as being off by 1mm on any part, or one screw too lose or tight and it will result in another issue... I've burned through many machines (2 t2's and 3 standards) and they all wear out the same. If anything, the T2 injectors wore out faster. As for the spring you point out, you can use your finger as you crank to keep the tension if said spring is lose, that alone wont help with anything once your tamper/blade/injectors wear down and the exact same half fill jam issue will get worse and worse, to the point you rip more tubes than you fill.
@Gypsy.313
Жыл бұрын
You're a God! 😅 Thank you for sharing this 🙏
@55ruthmarie
3 жыл бұрын
Well said! You stick to the topic and not So wordy. Thanks much!
@wallywool9617
Жыл бұрын
The arm with the spring has lots of dirt under it cause it to hang up. Spray carburetor cleaner under it while moving it to get the dirt out from underneath it. The slide plate underneath it needs to be filed or light sandpapered. Be careful with it when sanding it. Sand all edges lightly. Get the burs off. Also the arm that slides the tabbacco in needs to be filed with a fingernail on the ridges lightly. It will help the tobacco slide in the tube easier. Use Vaseline lightly to grease the track and joints. Put Vaseline on plastic shaft and wipe it with a rags clean. It will work like brand new! You need a 14mm wrench and a 8mm wrench and a 8mm socket wrench and a flat screw driver and a metal fingernail file. It's just that easy. When you have problems again just clean it.
@jacknguyen2912
Жыл бұрын
I rarely get the whole damn thing fill all the way because it has to be at least 5 years old. I couldn't find that 119 spring at HD. I read a comment in here saying that giving that spring a good few 360 twists and OMG... it works magic.
@superjoyyable
3 жыл бұрын
Exactly our problem! Thank you so much!
@markstreight1809
4 жыл бұрын
Thanks man hope a new spring works on my mew old model topomatic!
@joshbrekke6374
Жыл бұрын
This is a problem I have been having as well, along with the slop in the pins that hold the piston. Fixed that with a used ear plug, so a 119 spring I will go find. Thanks! Edit: I went to Ace and got the $2.02 #119 spring. It works however now the end of the tube is ripping off every time. Maby a lil stretching to the spring will help or tighten the holes up in the old original one if I ruin this #119.
@christ3187
Жыл бұрын
sounds like the cutter is having trouble pushing through it. Might be dull
@R-E-D-E-M-P-T-I-O-N
2 жыл бұрын
@tomking i have tried 3 ace hardwares and they dont have anything listed for that was wondering if you could measure the length and diameter of the spring or any info at all. yes i know this is 3 years old but the only thing i can find online is ppl say #119 from ace. thank u if u ever even see this.
@queeneywarren9474
Ай бұрын
I got one the of the spring is to thick against the wall tell me how on earth did you get it through that or if you got a video sure would help
@TheTrigzHD
Жыл бұрын
Thanks ! I just got mine and am having this issue I'm gonna try this out and I'll let you know if it works
@TheTrigzHD
Жыл бұрын
Worked out
@harukiii6218
3 жыл бұрын
I got a manual plastic slider from the brand top and it works great for me the only problem I have is sometimes I'll put a little too much in there and it'll tear the tip just a little bit but for 7 bucks I can't really complain
@jameskenney1340
2 жыл бұрын
They got a tops cigarette packer it's about 4 in Long and about an inch wide it's been used for about 4 years now it's made out of plastic best best one you ever have
@jameskenney1340
2 жыл бұрын
And it's a whole lot cheaper it's like eight bucks
@michaelmclaren1333
3 ай бұрын
What I do even tho it CLEARLY says not to is hold the rubber stopper down with my left index finger until right before it kicks the cigarette out. So the pusher is in between my finger and my thumb. I just help it hold the tube. It works with the original machine and the T2.
@lauracipoletti2202
2 жыл бұрын
Awesome! Ty and so far working for me too! Thankx again!
@OsborneExploration
Жыл бұрын
Can this soring be ordered online? My local Ace hardware doesn't have a selection of machine springs at all. Any help would be greatly appreciated!! Thanks in advance.👍👍
@benton-benton
3 жыл бұрын
I didn't feel like going to hardware store. So I thought, well try to make the rubber thing thicker. I have that sticky weather stripping stuff, so thought I'd give it a try, put it where the rubber thing goes, stick it on there. Guess what? It worked - at least one time anyway. After going 2 wks smoking half filled tubes, I finally have a real cigarette to smoke. Don't know when it will decide to stop working like that, so will go to hardware store tomorrow. Thanks for this video.
@footballwithethan1354
4 жыл бұрын
So I replaced the spring but now it holds the tube so tight that it rips the cigarette tube. Probably will change the rubber tip to a thinner 1 to see if it will work.
@seymourwrasse3321
Жыл бұрын
my machine screws up filling the last half inch on the end you light, it leaves a small pocket , and once you smoke to that point, the cherry falls off, any suggestions?
@rezolution6272
4 жыл бұрын
Thanks for the video have been throwing away smokes because of this issue daily. Why doesn't the manufacture just fix the fn problem?
@laragreene8328
3 жыл бұрын
They dont do anything about it because we complain to each other instead of to the company!
@infantrywagon
Жыл бұрын
Appreciate the video. Sadly That’s only the start of the problem. The real problem that will show itself once the spring stops working is the the part that closes as the handle hits a certain slop. It will start to not close all the way also due to a spring but replacing the spring won’t fix the issue this time. It’s an arm underneath that’s the issue, you need to find a video where it shows that issue and how to fix it with a super glue and a washer. The ive used tbis machine, the nice and heavy top-o-matic and premier supermaric. Hands down the best machine is the cheaper feeling “Premier supermatic II” best machine I’ve ever used but they break within acouple months depending on how many cigs you are rolling/smoking. Look up “premier supermatic 2”. There videos made by one man showing how to fix the slider to allow it to close all the way is simple. Taking alert the machine however is a but more difficult.
@JayFarm_23
8 ай бұрын
want to replace the spring but not exactly sure what I'm looking for. I tried looking up 119 spring on Ace hardware and I didn't see anything. nor did I see anything on the internet about a 119 spring. any help would be greatly appreciated thanks
@TheMixClub
4 жыл бұрын
just started rolling.. will give this a try.. Thanks for the video
@hughburka7491
6 ай бұрын
Help having trouble trying to find this spring what are the measurements
@deborahhine183
3 жыл бұрын
I have had mine for a couple yrs and it started doing the same thing I was getting disgusted with it I tried everything you did except for the spring going to try that ne😃
@hughburka7491
6 ай бұрын
I cant find that spring what did you ask for when looking for that spring
@user-ji3vf9nk1l
Жыл бұрын
Thank you for the info
@queeneywarren9474
Ай бұрын
Do you have any i deal the spring will last
@pattiannepascual
11 ай бұрын
very useful. thank you!
@candyhorvath9082
3 жыл бұрын
Thank you very much, I have been having the same problem.
Пікірлер: 206