Do you know if there’s a fix for the gear stick when the polyethylene or whatever disintegrates and the top part of the shifter no longer is connected with the part which connects to the gearbox. I’m talking about the section the gear knob screws to?
@hauyean86
Жыл бұрын
Hi CartuneNZ, Thanks for the detail video. I encounter a small problem and I hope you may help me.. I realized my J160 manual gear lever doesnt bounce back to center like normal manual tranny do. I have check the lower bush and it's in good condition. Then I have jack up, check the spring on the side of the gear shift housing and it looks ok too (is the spring wear and tear?) I got no Idea how to fix the "doesnt bounce back to center" thingy... Do you know what exactly happen? I really appreaciate if you could tell me if i missed out any springs or mechanism in the gear shift lever part.. Hope I may hear from you soon. Sorry for the broken English, love from Malaysia.
@michaelhyatt1696
10 ай бұрын
The two pins in my cover for the shifter a real loose is that something that I need to replace or try to tighten up
@samharris6871
Жыл бұрын
Hey man how do u replace the locking mechanism mines snapped but I’m not sure how to separate the gear stick in two to get the new one on
@antonyleggett828
5 жыл бұрын
hi kelvin, so are the W , G and R series main gear shifters all interchangeable between the series ? cheers Ants
@CartuneNZ
5 жыл бұрын
Hello Ants. Unfortunately no. There are different housings which bolt onto the box which the gear shifters fit into and different shifter. They fit into the housings differently. Cheers
@all4runner316
3 жыл бұрын
I put in a new g52 lastweek and put my shifter assembly into it, it occasionally goes sloppy and sometimes can't find 5th. Should I put the assembly that came with gearbox in and maybe solve it?
@CartuneNZ
3 жыл бұрын
I would be checking the seat , lower bush and pins. Then using the best components or replacing stuffed ones. Cheers Kelvin
@user-lc9zd6ol9k
Жыл бұрын
Can the gear stick be adjusted can u tel me how
@CartuneNZ
Жыл бұрын
There are several different positions of gearstick on the toyota gearboxes and they can mostly be interchanged. Cheers Kelvin
@larryseaman5185
Жыл бұрын
Please can you advise how I get the two pins from either side?
@CartuneNZ
Жыл бұрын
They tap out with a hammer and a punch. Cheers Kelvin
@tysonpoynter4883
4 жыл бұрын
Hey mate Ive got a 3rz 4wd Hilux and I was changing the shifter seat and cup bush and for some reason I can't seem to get the new cup bush into the selector so when I go to twist the spring loaded retainer back in it won't fully push down and lock and I'm not being a pussy about pushing it down and twisting but gee whiz it just won't go in plus my pins in the housing are wobbly and one looks a little bent. Could you please give me some tips and advice
@CartuneNZ
4 жыл бұрын
Hello. Some of the new bushes come with an extra rubber seal / o-ring on the bottom which wasnt present on the early ones. Its one of those changes Toyota did and they sell a new part which doesnt fit without that change. The pins in the housings often get bent and are wobbly and having new ones machined and pressed in is best. or making a sleeve into the housing to press the pins back into so they are held tight. Cheers Kelvin
@tysonpoynter4883
4 жыл бұрын
Hey know worries thanks for that it's a pain because I have replaced the shift lever seat but when I put the new lever bush that hose on the very end of the stick where the ball is now it won't slip back into the gearbox like the original dose is that ment to happen or should the new bush pop into the selector forks like the original?
@CartuneNZ
4 жыл бұрын
The plastic bush should push onto the ball and be held in place there. Once thats attached it sits into the gearbox hole
@revolutiondreaming
4 жыл бұрын
Hi. I have a Hilux LN106. On the gear shift lever housing, the two pins are completely worn away making the lever swing around everywhere and hard to get into gear. I can get a new housing from Toyota, but it's over NZ$120.00 There is another place in Aus which sells aftermarket pins which would need to be tapped into the holes and fitted. These cost about NZ$50.00 but the freight kills it. Any suggestions on where I can get an aftermarket housing in NZ? Or should I just look for a good second-hand housing? I also thought about removing it and trying to make my own pins, but they would have to be tight to stay in there. Any ideas?
@CartuneNZ
4 жыл бұрын
Personally I would be buying a new one. I have a box of used ones and they all have floppy pins. These pins are hardened so making new ones isnt so easy and to me $120 for to replace a housing thats lasted 30 odd years seems like good value. I'd also buy new lower seat and shift bush on the end of the lever. Cheers
@blakeevans8492
3 жыл бұрын
What did you end up doing? I have a similar issue
@CartuneNZ
3 жыл бұрын
I fit new housings most of the time. They are cheap and are like a new one, because they are new ones.
@blakeevans8492
3 жыл бұрын
CartuneNZ do you know the part # for a 1993 Toyota T100 4wd? By the way, thank you for your time and content.
@CartuneNZ
3 жыл бұрын
@@blakeevans8492 I use Toyodiy.com for part numbers. I have pictures. No T100 in nz.
@blakeevans8492
3 жыл бұрын
I have the same problem. How do I replace the pins mentioned at 2:55 ish?
@CartuneNZ
3 жыл бұрын
I buy new housings. There are pin kits available too but not that Ive used.
Пікірлер: 29