Thanks for the great video. I'm in the middle of tearing down and just thought how i would be putting these back together
@nicholasdougan957
Жыл бұрын
What was that degrease foam you used? Seemed to work well. Also great video, you're a beast.
@takeshi1242
3 ай бұрын
Whichever engineer had the great idea to put the cam seals inside the engine, instead of it being easily accessible on the outside, like the older non-VVTI engines, deserves a special spot in h3ll on top of a hot coal
@Autoenginecheck
3 ай бұрын
Thanks
@adamugarba9413
2 жыл бұрын
How the time of Ford expolara
@josephspellman2698
2 жыл бұрын
Did you add FIPG in the wells on the cam seal covers? I have seen 2UZ and 3UZ vids with sealant on the edges? Any leaks post install? TY for posting!
@Autoenginecheck
2 жыл бұрын
you have to apply silicone on the double cover of the camshafts , otherwise the oil will leak Apply 2 side Thanks sir
@bilge77
2 жыл бұрын
on the LH bank ( driver's side ) why did you turn until 2 dot marks lined up ? for access hole to line for service bolt...? why not the single dot ?
@Steve-um5mm
Жыл бұрын
The drivers side has two dots to line up, the passenger side just one. This keeps the cams side specific. This answer is not from my experience (soon though,waiting for parts!)but from watching other videos. If I find out differently when I do mine I will delete this response. Update: the left bank cams do line up with the single dots,AS did the right bank. Temporarily putting cam and crank pulleys and belt back on,rotated engine twice, the timing marks (and dots) lined up perfectly
@JeremiahOhana
Жыл бұрын
Did lightning up the one dots on the left bank work once put together. All service manuals say to light up the 2 dots on left bank and 1 dots on right bank. I did that but left bank timing is not in alignment.
@CristianCruz-jf4iw
3 ай бұрын
@@JeremiahOhana did you ever figured it out
@Chuycorona17
Жыл бұрын
Watched another video where a guy lined up the drivers side timing mark with the camshaft position sensor to access service bolt them removed cams, but there wasn’t 2 holes lined up on the cams inside and removed the cams that way. How will you be able to line back up after ? Asking because I’m tearing apart a 4.7 now and that’s what I did.
@Autoenginecheck
Жыл бұрын
When you match the timing marks to open the timing belt the cam pulley marks on the drive side will match but when taking the cam apart remember the EX cam gear has a tensioner to hold the 2 cams together. And there is a hole for 10mm bolt to fix it The drive side is down so the cam is aligned with the 2 mark
@jevtec2286
Жыл бұрын
Question? So the reals will not come out with out dessasembling the cams ?
@Autoenginecheck
Жыл бұрын
No sir
@JCManuel-c6p
8 сағат бұрын
👏👏👏❤️👍
@pogpapogpa3190
Жыл бұрын
1G
@Autoenginecheck
Жыл бұрын
2uz
@brentsanada6589
6 ай бұрын
Narration would have made this video Great. Okay effort
@Autoenginecheck
6 ай бұрын
Thanks for comment sir
@thegrey8643
8 ай бұрын
You're kidding me right? You have to remove the whole camshaft pair to replace a seal? Who's idea was this and is there a special place in hades for them? I've never seen such a stupid idea/design. If it aint properly leaking, nope.
@Autoenginecheck
8 ай бұрын
Thanks for comment sir
@thegrey8643
8 ай бұрын
I got over my surprise and just dug in to bang it out. Actually isnt that bad to do if you're already doing a timing belt and water pump job. Good video on the procedure by the way. @@Autoenginecheck
@CristianCruz-jf4iw
3 ай бұрын
@thegrey8643 was it complicated lining the tdc after putting it all together with timing belt?
@thegrey8643
3 ай бұрын
@@CristianCruz-jf4iwActually when i stopped whining about it and just got to doing the job, it really wasnt so bad. It wasnt hard to line up using some tricks from the toyota service manual. Just make sure to lock the exhaust cam sprocket with a valve cover bolt without the washer or something the same size and thread so the damper built into the sprocket doesnt untension when you remove the exhaust cams or when you install them.
Пікірлер: 25