This very helpful! I was very lucky I didn't have to go through any mahem, like you did. All I had to do was repack. A very educational experience. Thank you!
@NorthwindGarage
4 ай бұрын
Thanks For Watching 🇺🇸✌️😁
@robertfolk4583
4 ай бұрын
Most parts store will rent a race punch kit, makes it easy to install with no risk of damage. It also helps to throw the races in the freezer overnight. Good video, I like the rooster in the background. Cheers.
@NorthwindGarage
4 ай бұрын
Thanks For Watching 🇺🇸✌️😁
@brich2929
Жыл бұрын
bro, why are you reusing a cotter pin? Its such a critical component, and so cheap to replace?
@NorthwindGarage
8 ай бұрын
Thanks For Watching 🇺🇸🙂 👍
@brianensminger2237
Жыл бұрын
Just did this yesterday! I'm gonna start checking them more often! I used a hammer and punch from in behind
@johnwoody4905
2 жыл бұрын
nice video. i don't think you can get u.s. made bearing any more. last timkins bearing i got were made in turkey. you need to buy a washer to go between nut and bearing somebody left them out. keeps bearing and nut from damage. i have went thru that a lot it even worse when bearing locks up. take care, be safe and well.
@PuskwaskaOutdoors
2 жыл бұрын
@@NorthwindGarage Sometimes there is not enough room behind the nut for a washer and if you put one in it won’t give you enough room for the cotter pin so look carefully before hand…
@billypirtle1443
Жыл бұрын
Bearn puller works really well.
@NorthwindGarage
Жыл бұрын
I'll try it next time thanks for the info and Thanks for Watching! 🇺🇸👍🧔
@roygumpel8415
Жыл бұрын
As I am trying to install the new races, it required hammering down on it with a piece of wood, and once it was below the surface of the outside of the hub it is damn near impossible to somehow hammer it all the way in to where it stops at the little knobs. Insanely tight and beyond infuriating.
@TheHonro
2 ай бұрын
Cut just one side of your old race with a grinder, and use it as the driver. Then just pull it out when the new one seats. Ezy.
@nd1835
10 ай бұрын
Good work, I can't help but wonder why, for 45 bucks, you didn't just get a whole new prepacked hub?
@NorthwindGarage
10 ай бұрын
Because they didn't have one on the shelf and I needed the trailer that day. Hope that explains it. Respectfully thanks for Watching 🇺🇸🙂👍
@scrapeyhawkins5299
Жыл бұрын
Buy a complete hub kit ......
@steveflack9483
8 ай бұрын
NEVER, EVER use heat on an axle. Tempered steel strength is compromised when you do this. Use the proper tools for the job or leave it to the pros.
@NorthwindGarage
8 ай бұрын
Thanks For Watching 🇺🇸🙂👍
@RobertBenthal
Жыл бұрын
My seal and racer was impossible to get in
@NorthwindGarage
Жыл бұрын
You may have to really clean the surface where the new bearing assembly goes in. Very close tolerance there. Rightfully so to prevent movement after tightening. Also check your new parts to make sure you have the right one. Hope that was helpful. Thanks for watching! ✌ 🇺🇸
Пікірлер: 20