Thank you, thank you, thank you! I’ve been working on my lower belt for 4 days off and on( I work till I get pissed off and give up). This video is the only one I’ve seen that shows the brackets and I really appreciate the way you showed how the hardware went back together on them. I think I might just be able to complete this job today!
@BobBasshead
4 ай бұрын
The same here! Working on it till I get pissed off. After checking many videos Mr. Doby had the same machine as mine. Took out most of the guess work.
@djmiller1758
Ай бұрын
Thank you thank you. I am not a mechanic by any means but I was able to do this replacement. Long story short, I tried using an after market belt from Lowes. Compared to the old belt it looked identical. IT WAS NOT. As you said in the video is not an option. GET OEM trust me the others won't work. I made several attempts to get after market belt to work. It was way too tight and the pedal did not move freely. I gave up on the other belt and got an OEM belt. I had this mower in working order in 15 minutes. When I tell you I spent way too much time fighting the belt I was at my wits end. I watched your video over and over and over again. My mower , as far as preliminary tests go, is running better than before. Thanks again. You are the man!!
@mr.redneck421
11 ай бұрын
Out of all the videos I have watched in the last week to replace these two belts none of them showed the (two pulleys around 35 min part of this video) you just made my evening. If you lived close to me I'd buy you a case of beer. Thanks.
@lawrencewhalen1329
9 ай бұрын
I'm getting my 2017 Bronco ready for snow blowing season and decided new drive belts would be a good idea. I used after market belts without a problem but your showing of the proper order of the spacers on the tension brackets was a life saver. I also wish I had seen how easy the body comes off before I started the job, you can bet I'll do it your way next time.
@charlescole6599
3 ай бұрын
Thank you for the video. No other videos showed the BS over complicated pulley system this thing has. This really helped !!
@philliphall5198
Ай бұрын
I agree it’s the worst setup I’ve seen 😢😢😢
@insidethreewide7133
Жыл бұрын
Thank You so much Tom for making these videos! I purchased my Bronco new from Lowes in 2011 and is a 2011 model. I've had great success with it or maybe it's just luck, but it has been garaged kept the entire time and is in really good condition for its age. I have had those same original belts on there the entire time, and I figured it was about time to change them out before it left me walking. I ordered belts from Amazon (non oem) and as you would guess because you know what happened next. The belt was to tight and no matter how I adjusted the forward pedal linkage I could not keep the mower from creeping, but it did work so I cut the grass anyway because it needed it bad. While I was cutting, the first thing I realized right off the bat was that I was hauling ass, twice the speed as it should have. That thing took off and threw me back into the seat as if it was a top fuel dragster! So then I watched this video and you said that you have to use an oem belt. So I went to Lowes and bought a Sunbelt brand that was stamped oem with the same manufacture part number and changed the belt. Same thing happened again. So, I watched the video again and noticed the oem belt that you were using was an actual oem belt. So, I purchased my third belt and changed it out and bam! Problem solved. I failed to mention that before I installed it I measured and compared the Sunbelt oem belt to the Lowes belt and the Lowes belt was approx1.5mm thicker in belt height not width than the Cub Cadet belt. Wouldn't think it would make that much difference, but boy did it! So, I got to thinking, and if my thinker is working properly 1.5mm x 2 = 3mm per pully x 4 pullies is 12mm which would be approximately 1/2". That 1/2" is actually making the older belt tighter than the thinner belt therefore not allowing enough slop in the belt to stop driving the mower, or in this case allowing for it to creep. I am only leaving this detailed problem that I had is to back up your statement that "you have to use the oem belt" or some weird thinks would happen if you didn't, as I heard another tuber, can't remember who it was, but that was a textbook example of what would happen if you chose not to use the oem belt. I'm a huge fan of your channel and I look forward to your future videos, but I have plenty more to watch before then. Thanks again, I was just about to haul this thing to the shop and have no clue what that would have cost me of money that I need more than that shop would. This video definitely "was my dinner". 😁 😂
@TheOzthewiz
3 ай бұрын
The same thing happened to me a couple of days ago. I purchased a pair of "OEM" belts ( they were packed in a GENUINE "Troy Built, MTD sleeve). I installed them (without lifting the body) in a 2005 MTD yardman mower, which I had replaced 10yrs earlier with non-OEM "Rotary" belts (worked like a charm for TEN YEARS). The "GENUINE MTD" belts off ebay ($38 for the pair) started doing FUNKY things like lurching ahead when put into gear. The takeaway from all of this is that to get OEM belts, you have to cough up at least $90. The quality of parts you buy today compared to 10yrs ago is a F**KING JOKE!! And beware of the fake "OEM" packaging, it will bite you in the arse 19 different ways!!!
@wayneasiam65
10 ай бұрын
When you started whistling I changed it to full screen after giving the video a LIKE.
@reginaldhall6871
Жыл бұрын
Great in depth video, Thank You!! I used the wrong belt on my last mower. It didnt work, & I thought I had put things back together incorrectly. Now Im repairing another identicle Troy Built 42 inch mower but this time I have the OEM belts. Your video is saving people both time & money.
@robertcombs5640
11 ай бұрын
Just wanted to thank you for this detailed video. Yeah it's not an easy job at all. That top washer is a beast. I did this job pretty much the same way but through the deck (yeah I still have that washer and it's going back on soon). Did the replacement before my impact wrench purchase and it almost killed me! Man just know so far I've been searching for a Comprehensive video here for about 6 weeks on this subject. I have yet to find a good guide for the adjustment but do know how to do it. So far its trial by "tightness". Awesome job on a booger of a project and just a great video.
@wayneasiam65
Ай бұрын
I could tell by the way the dogs responded when you told them to shut up that they were bad boys.
@burtburt1755
11 ай бұрын
I found your channel this evening. I just happened to be working on one of these mowers. First one I've seen like this. I learned so much from watching this video. Glad you showed how to take the body off. I liked it and subscribed. Looking forward to watching more of your videos. Great job
@bigsonslawncare
Жыл бұрын
I had one of these some years back and attempted this same job in my front yard! It was a BIG FAIL! Had no clue that it took all of this, you tackled it like a champ💯💪🏾
@TomDobyMowerRepair
Жыл бұрын
It Was A Punishment for SURE!!!!!!!!!!
@CHELLIE2408
10 ай бұрын
Nice Repair Tom 😊 I have to Admit that at the 34 Min Mark watching you Work so Hard I Got a Little Tired and had to take a Nap 😋 I am good to go Now 🤩 I Bought a Troy bilt Pony Mower had it for about 6 months Now I Bought a Snow blade for it and Have been using it as a Dozer 🤪 to scrape the weeds on my 1/2 Acre yard I had to buy a riding Lawn mower because Arthritis has set into my lower back and I can no longer push a Mower I use the blade to scrape the weeds with and I use the Double Pallet that the Mower was shipped in as a Drag I have not used the mower part of the mower Yet 🤭 the Yard comes looking great But I know I am being hard on this mower I already whore out the bearing cup assy on the Variable speed pulley I am Replacing the Bearings with Timkin Bearings and I ordered a new bearing cup holder parts should be here soon Keep up the Great work Tom Chellie Retired Female Fleet Equipment Mechanic of over 50 Years
@jamesashton1923
6 ай бұрын
So glad I found your channel Tom. Well done and very helpful. Love your execution and sense of humor.
@kathyfrancis6209
Ай бұрын
Thank you for a helpful video The part number for this belt on my deck lid was the wrong one so I ended up putting a belt in that was too short also. It was only an inch to short so it fit without any problem but the mower would not stop when you let up on the speed control. Thanks for helping me figure it out
@BrianHunter-w6j
Ай бұрын
Hay Tom you d o real good work an show people' how to do the job right my husband will be real happy to watch your video
@kevincelebrado5311
Жыл бұрын
This is next level repair! I love it! Thank you!
@stephenzampedri8712
Жыл бұрын
I wished I watch your video earlier. I just put one back together. This video would of made the job a lot easier!! Thanks for the great content.
@mowersbymitch
Жыл бұрын
Those are some fun mowers. Over half the mowers I work on throughout the year is some MTD Crap. You hung in there and got it done. 💪
@philliphall5198
Ай бұрын
Yep and we change the max to work on this unit because of the crap and time it takes, Plus we will replace both belts or none 😊
@projectfamily5802
Ай бұрын
Thanks for the video I would have never figured it out
@projectfamily5802
Ай бұрын
I am missing that big spring you hooked on the towards the end of the video do you know what it is called thanks
@LL-xv1gt
Жыл бұрын
Appreciate this video, obviously it will save alot of time, money and frustration. Thanks.
@Big_Johns
Жыл бұрын
Those are always so much fun Tom, why they put the crossbar directly over the pulley nut baffles me. Great video, you did good bud. 👍
@philliphall5198
Жыл бұрын
I used a bir grinder and made a place for my 7/8 socket to fit Can’t see what it will hurt as big as bar is
@Big_Johns
Жыл бұрын
That’s a good idea Phillip, thanks bud. 👍🏼
@DOCREAL1118
Жыл бұрын
Always enjoy watching the videos brother. Thanks for taking time to share all you have learned. That was a tough one man. Great video
@louroberts5567
Жыл бұрын
Toooom Doooobyyy! Nice job, man! Lots of good info. We can always pick up some good tips from your videos. Thanks for sharing!
@TomDobyMowerRepair
Жыл бұрын
thanks Lou!
@HeistiCon
Жыл бұрын
This was the only video I found with this type of puppy system. You sir are a legend.
@HeistiCon
Жыл бұрын
Puppy haha. Pulley
@charlesday3373
5 ай бұрын
Thank you Mr.Tom D. !!!
@hooksn2lips
Жыл бұрын
Looked like a knuckle-banger job right there!
@TomDobyMowerRepair
Жыл бұрын
thats a box of band aids right there!
@philliphall5198
Жыл бұрын
That’s a fact for sure so ware gloves
@miguelalt8855
Жыл бұрын
Tom, you did a great job with this video, thank you. I recently changed the drive belt in my Troy bilt pony (2011), unfortunately, I didn’t see your video before, didn’t get the OE belt you recommend, I got the Sunbelt but I will be ordering the one you mention and replacing it again; the sunbelt belt is very tense now, not sure if that’s the way it’s supposed to be, I don't know if that will be the cause of my problem, now I can only control the speed with the throttle lever, even when I put it in rabbit mode the motor goes at high rpm, but the ground speed is about half the normal speed; the (yellow on mine) speed control lever doesn’t work, it goes up and down without locking the notches, offers no resistance and does nothing. (however, the engaging of the parking brake action works fine). I opened up the hood and saw the speed control lever attached to a connecting rod which is attached down there to the cupped metal piece in the correct position as the new Troy Bilt Pony I saw yesterday at Home Depot, but besides allowing to be put in in park position, I don’t see it attached to anything else, is it right? How does it regulate the speed if it is not connected to anything else? Thank you in advance.
@TLMD
Жыл бұрын
Nice video brother. Keep up the awesome work!
@phingly2151
3 ай бұрын
Thank you for the video.
@johnnyreagan1
Жыл бұрын
Great video as always! Valuable info that you always share with us! GET IT!
@TomDobyMowerRepair
Жыл бұрын
I appreciate that!
@johnnyreagan1
Жыл бұрын
Just noticed you didn't have the "Buzzer" Channel on in the background.......lol
@texasbasementbuilds4543
5 ай бұрын
yup, replaced the deck and upper trans belt on my Troy Bilt 30. 50 bucks each.
@TheOzthewiz
3 ай бұрын
Just because you use "OEM" marked belts doesn't mean they are OEM. I just purchased a pair of "GENUINE OEM" belts off ebay and they worked like CRAP. I needed to replace a set of 10yr old "Rotary" (non-OEM) belts on my 2005 Yardman mower. I guess the ONLY way to get OEM belts is to pay $90 for the pair! Btw, "Taryl Fixes ALL" replaced all the pulleys, belts, variator bearings WITHOUT lifting the body and he used ROTARY belts, although his video is 7yrs old. I would say the quality of parts back then was MUCH, MUCH BETTER than it is now! FACTS!!
@philliphall5198
Ай бұрын
Try Napa or gates belts😊
@billcallahan9303
11 ай бұрын
DeWalt tools! Smart man! I got some so old they were with Moses when he parted the Ohio River! Legend has it, they're still being used by the Hari Krishna sect in building temples in north Texas. True story!
@philliphall5198
Жыл бұрын
My lift table is just like yours Same one and it came from a old HD shop in Oklahoma Love it
@TomDobyMowerRepair
Жыл бұрын
I think I paid about 1200 for it 5 years ago, think they're over 2000 these days.
@philliphall5198
Жыл бұрын
@@TomDobyMowerRepairlike every thing keeps going up and up now It’s great for my back not beening over
@TomDobyMowerRepair
Жыл бұрын
@@philliphall5198 right, I can't work in the floor after shoulder surgery, hip replacement and spine fusion haha
@mr1pearl
Жыл бұрын
Another success story yeh buddy 👍
@TomDobyMowerRepair
Жыл бұрын
thanks bill!!!
@gadasavideos8564
3 ай бұрын
I've used aftermarket but only if they come with mtd number on them
@JohnSmalls-hx3th
Жыл бұрын
Thanks for the video just what I needed to put this dry belt on those two damn transaction bully thanks
@ronslawnscrystalriver2151
Жыл бұрын
That toolbox tho🤯#LookAtIt💥🤩
@TomDobyMowerRepair
Жыл бұрын
haha LOOK AT IT!
@jermainechoice2356
Ай бұрын
This video shows everything
@dnrsmallenginerepair
3 ай бұрын
Very awesome work friend
@philliphall5198
Ай бұрын
Would be nice if you listed the brand, size and model number for those who are looking for serious help with their mowers 😊😊😊 Just a suggestion
@robertspencer9345
4 ай бұрын
Darn, I have to change my belt and its an auto too if there was an easer way im sure you would show it. THANK YOU,
@davethomas3553
Жыл бұрын
Just bought a troy built Bronco, from a guy that was moving. It takes off fine, goes several yards, then hiccups, continues this but erratically. May be good for several yards, or may jerk every few feet. The top belt is oem, and in very good condition, then bottom belt not sure if it's oem. It's pretty new as well. So, you are saying it could be acting up because the long belt is probably not oem?
@TomDobyMowerRepair
Жыл бұрын
absolutely!
@davethomas3553
Жыл бұрын
@Tom Doby Mower Repair well, new oem belt. Same issues. Anyone have a video, etc of someone rebuilding one of these ? It appears that is in my future
@henrymurawskibigdogrepair
Жыл бұрын
The last thing, putting the belt on the drive pulley off, the engine, would be a lot easier then to do it first
@billturville15
21 күн бұрын
what raising table are you using and the model number? Thanks your video was very informative.
@TomDobyMowerRepair
21 күн бұрын
@@billturville15 I did a video on my table a few months ago, I got it from derekweaver.com
@user-mc4no4du1j
11 ай бұрын
I am currently involved in chang8ng the belt. You showed the oem belt earlier and it has two sets if numbers. Not just the 954 it has a 754 can it be either long as it matches those numbers? I changed my belt with a 754 and now no brakes and it moves without pushing pedal!. An love your set up. I did mine in the gravel jacked up on blocks with only deck dropped to ground.
@user-mc4no4du1j
11 ай бұрын
I also changed belts not long after owning mower and never had this problem!
@TomDobyMowerRepair
11 ай бұрын
you HAVE to use the OEM belt or it will do that, what brand belt did you use?
@user-mc4no4du1j
11 ай бұрын
@@TomDobyMowerRepair 7544067 5/8 x 90.8 Sunbelt for MTD, CC, TROYBILT, YARD MACHINES, HUSKEE
@TomDobyMowerRepair
11 ай бұрын
yea thats from home depot or lowe's, has to be OEM
@user-mc4no4du1j
11 ай бұрын
@@TomDobyMowerRepair S
@dewEasy2022
Жыл бұрын
Thanks!
@TomDobyMowerRepair
Жыл бұрын
Thanks!
@philliphall5198
Жыл бұрын
I took a good bir grinder and remove some on cross over bar to get 7/8 socket on big upper pulley
@sherwoodchevy
Жыл бұрын
Im a car restorer and changed same belt.What a PIA!!! Thanks for tutorial.When I got done it ran fast but would slow when I stepped on brake but not stop?
@TomDobyMowerRepair
Жыл бұрын
did you use the true oem belt? on this one i had to take the body off because the customer took the main bolt out and lost the washer between the frame and floorboard, i called him and he found it where he was workin on it and brought it to me thank goodness!
@sherwoodchevy
Жыл бұрын
No got 80.4" belt from lowes COULD IT BE TOO THICK? I even took apart brake pads n washed in soap n readjusted but stil wont stop and its hard to shift?
@TomDobyMowerRepair
Жыл бұрын
@@sherwoodchevy has to be oem, they may be the same length but the thickness and shape and angle may be different
@eddieh6429
Жыл бұрын
Tom Doby! THE SMALL ENGINE REPAIR GOAT! My aunt had one similar and I used to cut her gras with it, hers was the biggest pile of dog $&@$ I ever cut grass with, great job on this one! Great video! Watch out for At TRAIN TOM😂😂👊🏼
@TomDobyMowerRepair
Жыл бұрын
Thanks Big H! I wore your shirt in this video
@eddieh6429
Жыл бұрын
@@TomDobyMowerRepair hope to see you live action tomorrow 👊🏼
@OutLawOkie
Жыл бұрын
Thank god i have John Dear it little easy than that
@TomDobyMowerRepair
Жыл бұрын
amen brother!
@snicks50
Жыл бұрын
good old Murray
@ronaldwprovo5530
Жыл бұрын
Thank you,
@djmiller1758
2 ай бұрын
M transmission handle js really loose after doing this. Is there something that may have been taken off and not replaced. Spring maybe?
@TomDobyMowerRepair
2 ай бұрын
theres a long spring that holds it up
@markchristman1076
Жыл бұрын
Just removed body from 2004 GTX2654 Troy Bilt to access nut holding idler pulley. Pretty ridiculous just to get to one nut.
@philliphall5198
Жыл бұрын
I drill a one inch hole now and got rubber plugs to fill them I made a jig and mark it and hole saw, faster and cost customers less money
@philliphall5198
Ай бұрын
I made a jug to drill hole in floor and add rubber plug 😊😊😊
@alexchavez5500
9 ай бұрын
Hello Tom need your expertise I got a troybilt bronco 2018 I replaced the drive belt but it won't go reverse very slow un less I help rotate it same with forward belt its kinda loose any suggestions thanks
@TomDobyMowerRepair
9 ай бұрын
just make sure you have the proper OEM belts, and check the vari-drive pulley to make sure it slides easy
@donvoll2580
Жыл бұрын
Good day from Ontario I have MTD 46, alotlooks same. Never seen seat shroud off before. I am 73 & was thinking of making riding tractor with high speed. So would u take back big pulley off & put smaller on instead ? My solenoid is shot, could figure out how to get it out remove I think I will subscribe Thanks
@TomDobyMowerRepair
Жыл бұрын
i have never built a tractor for that believe it or not, not sure how they do it
@patmadix172
Ай бұрын
Have a troybuilt bronco and I have to turn the motor off to change gears. Is that the pto because gears working fine
@TomDobyMowerRepair
Ай бұрын
sounds like something with the pulley pivot, something is jammed
@Butler_Buck
24 күн бұрын
My mower threw that drive belt today. The belt is wedged between the two pulleys and I can't get it to free up. Do you think I will need to take the pulleys apart to free the belt ?
@TomDobyMowerRepair
24 күн бұрын
may have to
@Butler_Buck
24 күн бұрын
@TomDobyMowerRepair I was afraid you'd say that. Trying to get one or two of my handier friends to help me out by offering breakfast. 😀
@celcossac
Жыл бұрын
Te saluda Rolando castilla compre un troy bill 42 7 velovidades hace seis meses cortando cesped se trabo lo destrabe pero no arranca solo da vueltas .esta bien la bobina de alta .bien la bujia bien el carburador. E regulado las válvulas y el motor solo da vueltas.e revisado la compresión no marca nada .puedes ayudarme que mas debo hacer.muchas gracias en espera de tu respuesta
@TomDobyMowerRepair
Жыл бұрын
Must be a valve issue if there is no compression
@philliphall5198
Жыл бұрын
Theses are the hardest ones I’ve ever put belts on It’s a time job and it will cost them to
@AndyWaddell-hz1es
Жыл бұрын
Hey Tom- I have the same mower and replaced the belts but the clutch/brake is loose, and the auto transmission pedal is super tight. Could the reason be an incorrect belt? Sounds like it has to be a perfect OEM match from your video...
@TomDobyMowerRepair
Жыл бұрын
yes it HAS to be an OEM belt
@AndyWaddell-hz1es
Жыл бұрын
@Tom Doby Mower Repair Thanks Tom- I've ordered the OEM belt and will give it a try!
@AndyWaddell-hz1es
Жыл бұрын
Tom- finally received the new OEM belt, put it on, and BOOM! Problem solved! Thanks again for the information and step by step video instructions!
@philliphall5198
Ай бұрын
I just drill a one inch hole in floor Have a jig made up for it
@philliphall5198
Жыл бұрын
I usually get them with a box of parts and bolts because they give up
@billsimpson604
Жыл бұрын
That was a bummer!
@philliphall5198
Жыл бұрын
What about just using a hole saw a put a hole in the floor????
@tellfile
3 ай бұрын
I don't suppose there is a drive belt slack adjustment in there anywhere.
@TomDobyMowerRepair
3 ай бұрын
no
@tellfile
3 ай бұрын
@@TomDobyMowerRepair I found one adjustment that really works ... a little quirt bottle of gas on the belts through the battery compartment while the belts were halfheartedly spinning. Before that, the rider would not move very much (even after two new belts were put on), so when I squirted them, they grabbed and spun like crazy. It would pull up a very steep bank with no problem. Then after it sat a while, it went back to not moving very much again. The reason I thought of applying the gas is because I treated the belts with belt dressing earlier and after that it really wouldn't move. It's like the pulleys and belts were coated with a teflon like slick from the belt dressing and the gas had a positive effect making them grip. I saw no signs of any oil leakage on the belt from the front engine pulley. Too weird. I thought belt dressing was a good thing to do.
@philliphall5198
2 ай бұрын
It’s no fun on this mower, really it could have been simpler but they don’t want the average person to service it
@gloriamorelli7152
8 ай бұрын
if i order by that part #, will i get correct belt?
@TomDobyMowerRepair
8 ай бұрын
make sure to get the OEM belt
@jasonwilloughby6538
11 ай бұрын
Hey I have a mower like that one and can’t get the variable speed pulley off because the bracket has a hook that attaches to the rear axle. Please help!
@philliphall5198
Жыл бұрын
That’s just like my yard some thing mower
@mr.redneck421
11 ай бұрын
Can you help me? why is the new lower drive belt smoking on my troy built riding mower
@TomDobyMowerRepair
11 ай бұрын
did you use an aftermarket belt, there may be a frozen idler pulley or the belt may not be installed correctly or it may be outside of a belt keeper
@mr.redneck421
11 ай бұрын
@@TomDobyMowerRepair I will check tomorrow. Thanks
@426superbee4
Жыл бұрын
I like them a little wider. They shave off to the right fit 🤪 Really i have plenty of room to work on it. Rather taking the body off. Reason being is? All the handle will be come loose, and have to start glue them in
@TomDobyMowerRepair
Жыл бұрын
had to take the body off because the customer botched this job and lost the thrust washer between the body and chassis
@426superbee4
Жыл бұрын
@@TomDobyMowerRepair There made to take off. but i rather not. I understand that cheers
@426superbee4
Жыл бұрын
I would be replacing some dam pulleys
@timpearce5375
Жыл бұрын
Glad I dont have one of these POS. Especially one I have to hold a pedal down to go... I wouldnt have one of these things.
@timpearce5375
Жыл бұрын
That other belt probably should have been replaced too. Screw doing this over again.
@TomDobyMowerRepair
Жыл бұрын
i'm with ya on that!
@RogerRabbit-lx1rc
10 ай бұрын
You only need to push the pedal down to go and then there's a button on the dash for cruise control and take your foot off of the pedal.
@whatdoyouthinktodd
5 ай бұрын
You're not making me dizzy but I bet you get your steps in everyday. You need air conditioning I can tell it's warm in there I would have air. Or do you have air first time I've seen this channel so I have no idea
@TomDobyMowerRepair
5 ай бұрын
No air, it's not insulated, I use fans, come about noon I have shade and the sun is behind the shop
@user-uh6py7vr3k
5 ай бұрын
You help me do my self thank you so much
@tomc8988
Жыл бұрын
what is the correct belt size i have 90" seems a little long
@TomDobyMowerRepair
Жыл бұрын
gimme a minute to look back on it, you have to use the OEM belt, aftermarket belts wont work good cause theyre not exactly the same... even if theyre the same length
@TomDobyMowerRepair
Жыл бұрын
that should be a 9450467a belt, 91 inches, make sure its routed correctly, when you install it unset the parking brake and check it
Пікірлер: 145