Thumbs up this comment for the podcast.. we’ve been brewing on it ✊🤙
@Theroeders12
Жыл бұрын
You both definitely need to do the fireside chat together! Fireside with Josh and Tim and throw that on some t-shirts!
@Over_The_Top-1320
Жыл бұрын
Why did the inner bearing nut (covered with grease nut) and bearing need to come out? All that you did was tightened the new mylar nyloc nut against the weld ring (backed up by the outer bearing nut). Just hold the VERY TIGHT outer nut with wrench, slide weld ring in place, screw on and tighten the new mylar nyloc nut against weld ring, done. What am I missing?
@Aldocello1
3 ай бұрын
I agree , hes usually a very smart man but he made this more complicated than it is
@drewanderson502
2 ай бұрын
When are we going to get a video on how to make your power draw board? It obviously has some sort of threaded internal rods that connects to the impact wrench that travels inside a channel/track
@tedgifford1627
Жыл бұрын
Thank you for this lesson guys. I went with a standard grade 8 home depot 5/8-11 nut and a 5/8-11 nyloc nut. The total length came after the LCA nut came out to be 1 1/4" with these two additional nuts when installed. They both lined up snug with no crush washer needed. You can get a standard 5/8 crush washer from your local gun shop with no issues, just another stop. My welding shop does not use crush washers so I just used the two additional nuts. My 3/8" Milwaukee 12v ratchet, 1.5 AH has more than enough power to operate my ultimate press. edit: was wanting to upload some pictures to maybe assist with this lesson. edit again: The bearing plate was not loosened with the mods that I did. Keep it KISS right?
@heathhenry6083
Жыл бұрын
Tim and Josh are an awesome duo! Great video!
@RugerNuger
Жыл бұрын
So how come u used a welding ring and not just a normal washer ??
@billhindorff8200
Жыл бұрын
Timely. Just bought my bow press from you yesterday. :)
@anthonykott9707
Жыл бұрын
Nice, thx for the knowledge!!!
@perryknetter8577
Жыл бұрын
Thank you for sharing
@jons7e
Жыл бұрын
Maybe this is a future topic to cover... how to read the paper tuning tears and what adjustments to make based on the size and type of tear you see
@IntrinsicRoots
Жыл бұрын
How ironic I just bought a press from ya that’s on its way in the mail, thanks josh🥂🤝
@lindesylittlechief9056
Жыл бұрын
Thank you Tim and your welcome Josh hahaha I asked him to help video you hahahaha great video guys
@colemantaylor6996
11 ай бұрын
That tripod would work great for my elk hunt this September!!
@engineerz_hero6771
Жыл бұрын
Good to know for when I place my order of the ultimate with you
@88northoutdoors29
Жыл бұрын
Nice
@madman432000
Жыл бұрын
How about a 12V drill instead of an impact wrench? Maybe not enough power to press the bows?
@dougieripley2095
Жыл бұрын
Awesome simple video for you guys! KISS is king Keep It Simple Stupid
@ImperiousArchery
Жыл бұрын
Show us how to make your drawboard next?…..
@poppasmurf15
Жыл бұрын
Can I buy the wheel from you?🤔❤️
@trevorbritton4433
Жыл бұрын
Can you do a private video on spot hog arrow release the new ones from 2023 please thank you
@marksamluk9879
Жыл бұрын
I got my press from you
@juniharoon
Жыл бұрын
Im trying to follow the steps in the video and turn my bow press into a power press. But i cant get the nuts to loosen up. They are actually starting to strip and not loosen. That made me wonder, do I really need to loosen the nut and why?
@juniharoon
Жыл бұрын
Just to follow up. I eventually gave up on loosening the nuts and screwed on the lock nut until it was snug and lined up with the other nut. The screw sticks out but it works perfectly. Here here to my DIY power press. Thanks MFJJ!!!
@crustymarine86
Жыл бұрын
I wanna know how he made the draw board thats in the shop. The one he uses a drill to draw the bows
@gavinbensutherland508
Жыл бұрын
Hey Josh and Tim please show your draw board so I can try make my own .
@CBFish
9 ай бұрын
Looks like the same concept as a press. Punched square tubing mounted on the press. A piece of electrical strut with all thread ran down it. A bearing like the press to allow it to spin. Put two square nuts internal on the thread and weld them a couple inches apart to a piece of angle or something that sticks out the front of the strut so you can attach your eye to it. Weld some square tubing horizontal down low to offset your grip peg.
@justintorres08
Жыл бұрын
👍
@waynehumphrey8910
Жыл бұрын
You didn’t put glitter on them lol
@MikeOxford
11 ай бұрын
Think I'm going to puke from the camera motion and missed autofocus. Gimbal + manual focus please. Ugh...but good info on jamming your nuts up to make the in-and-out easier.
@drewolm
Жыл бұрын
W!T!F! Did you guys just mis gender some bow press parts????!!!!!!!!!! Have we learned nothing?????!!!!!!
Пікірлер: 33