After following a couple other tutorials with no success, I thought I'd bricked my main board-but turns out this one got me back up and running. Thank you!
@Bruceanddenise
9 ай бұрын
Worked again with the most recent addition of a CRTouch and newest version of UF2 firmware. FOLLOW the directions folks, don't mess yourself up by missing the details. ALSO, if you install your CRTouch but don't get around to installing the firmware for a week or so, BE GENTLE with your probe. I was chasing firmware issues and I had a BENT CRTouch probe tip. Bent back and now it's back in action.
@Bruceanddenise
9 ай бұрын
Don't overthink the firmware update.
@TH3DStudio
9 ай бұрын
Yeah you have to be careful with the "Touch" type probes. The pins are easy to mess up and it will make it stop working correctly.
@Bruceanddenise
Жыл бұрын
Worked like a champ! $50 Ender 3v2 I picked up on CL, minus touch screen, is up and running with your 12864 LCD kit. Thanks for all the support!
@kevinjones6924
Жыл бұрын
Awesome video Tim, thanks! Between your original setup video and this one, there shouldn't be any reason someone, even without the technical skills, couldn't upgrade their own firmware! Great stuff!!! 🥇🥇🥇🥇🥇👏🏻👏🏻👏🏻👏🏻👏🏻
@TH3DStudio
Жыл бұрын
I appreciate that!
@legion2k988
10 ай бұрын
Thank you! Worked like a charm. Did the LCD upgrade on an ender 5 plus and now I'm doing the EZABL upgrade. You guys have made it very easy, thanks for taking that extra effort. Keep it up.
@TH3DStudio
10 ай бұрын
Our pleasure!
@machinistx-.4286
Жыл бұрын
Can’t get much easier then that right there. I followed the previous videos on firmware a couple years ago to get my E3pro & E5pro going. Both work great!
@TH3DStudio
Жыл бұрын
Glad to help
@idiotluggage
3 ай бұрын
Thanks for sharing this. I recently got an Ender3 with the EZABL Pro that I am trying to get working.
@TH3DStudio
3 ай бұрын
You can do it!
@danielpayne2452
6 ай бұрын
WWWWWWWWWWW this is the only thing that worked to flash my 1.1.4v card onmy ender. thank you!!!!!
@ChrisRubeo
Жыл бұрын
Awesome - worked like a dream. Just put in the silent board to my Ender 3 Pro - now this for $5. Awesome!
@colinellison5659
Ай бұрын
i watched the video after having my printer down for months following a board swap. when you said "if i had a stock printer i would click build" i did that and ran through a plethora of issues. then i watched the video all the way through. I added the abl option in marlin and it seems to be cruising now. fingers crossed.
@TheSinzia
Жыл бұрын
Love the new intro! Great video for firmware stuff. :)
@TH3DStudio
Жыл бұрын
Thanks! 👍
@averageengeneer
5 ай бұрын
Incredible guide! I used it just today to update my cr10 firmware!
@TH3DStudio
5 ай бұрын
Glad it helped!
@fizdog
Жыл бұрын
would like to say mines a completely stock ender-3 and this video was very helpful. thanks!
@TH3DStudio
Жыл бұрын
Very welcome!
@valdemarcarneiro4211
9 ай бұрын
Thank you salutation de switzerland
@MrQuick1965
Жыл бұрын
Pretty informative , but still a bit confusing, at least in the environment build section I see my chip listed GD32F303RET6 ,, with the marlin 2.1.2 and the other config.h the GD chip is not available.
@koent7788
8 ай бұрын
Exactly, the new GD MCU needs some more attention since stm is replaced with the newer gd boards since 2022. I'm desperately looking for firmware that also supports a cr/bl/3d touch and works with the new Giga Device mainboards. Have you already got your printer up and running with custom firmware?
@WreckDiver99
Жыл бұрын
Video drops 2 hours after I ranted on the other video that there was no good info on doing this for my Ender3 8-Bit board. LOL... THANKS GUYS!
@TH3DStudio
Жыл бұрын
It's for everyone but you. :P
@WreckDiver99
Жыл бұрын
@@TH3DStudio too late
@TH3DStudio
Жыл бұрын
@@WreckDiver99 dang it! lol
@jerryatricks4168
3 ай бұрын
Everything worked fine up to the point where you clicked on the Build button in the lower left corner. My VSCode doesn't have that button.
@TH3DStudio
3 ай бұрын
You missed a step somewhere then
@petersilie3090
3 ай бұрын
it is the tick to the right of the home icon.
@petersilie3090
3 ай бұрын
it is the tick to the right of the home icon.
@11northexoticsjustin74
7 ай бұрын
I flashed a bootloader using the bootloader video and that worked perfectly, then installed this firmware on an original cr10 i got used for cheap. at first i had issues with the hot end temp fluctuating to much and tripped the thermal runaway i believe (printer just reset). I had the part cooling fan set to turn on after 1st layer and i think the combo of hot end temp dropping from 230 to 220 plus the parts cooling fan over shot the temp and it would drop to about 210 and it couldn't get back to 220 before thermal runaway kicked in. changed the fan to come on after 3rd layer to give 1st to 2nd layer temp change time to stabilize and now it will finish the print without tripping thermal runaway. works but feels like a band aid, at least i know thermal runaway works. would adding a moffset to the hot end fix this more permanently? also i now have the baby stepping option in the tune tab on the printer screen but when i adjust it up .025 and save settings, it just says 0.000 when i go back to z baby step tab. shouldn't the baby step setting be showing in the tab after adjustments?
@TH3DStudio
7 ай бұрын
You'd want to run a PID tune with the fan on. Thats pretty common on some hotend cooling setups. As for the babysteps, those ONLY save when using an ABL. If you constantly have to adjust without one, level your bed.
@ChefDansHookah
4 ай бұрын
Good evening. I followed the video instructions and I get this message each time: "MissingPackageManifestError: Could not find one of 'package.json' manifest files in the package". Any info on how to fix this would be great. Thank you kindly.
@TH3DStudio
4 ай бұрын
Probably opened up the firmware at the wrong level or it's a network issue.
@ChefDansHookah
4 ай бұрын
I opened it up just as the instructions said. Went through it step by step. Either way I was given some firmware that seems to be making it work. I'm still going to be purchasing your guys's stuff in the future so I will definitely hit you up when I have another technical issue. Have a great day.
@alexbinyon9647
25 күн бұрын
i dont have a tick/ check mark at the bottom left ? i do have platformIO tho ?
@tohard18
Жыл бұрын
I keep receiving this message when i run the test, send help. MissingPackageManifestError: Could not find one of 'package.json' manifest files in the package
@TH3DStudio
Жыл бұрын
Usually that's an issue with the local computer. Close VSCode, delete the .vscode and .platformioini folders from your user folder, then reopen VSCode.
@balbestblapipa
2 ай бұрын
Could you please place somewhere PORTABLE version of VSCode with proper components that close enough to video guide.
@TH3DStudio
2 ай бұрын
Haven't been able to get a portable version working.
@Svenisko1705
Жыл бұрын
(Original comment edited) My pritner is now running, but X axis is weird (looks like it is set to behave like a Ender V2 with not centered nozzle.) At +235 X, nozzle is like 3cm from edge.
@TH3DStudio
Жыл бұрын
Use the HOME_ADJUST feature to set your home offsets.
@chewbaccarenfrey
11 ай бұрын
Thanks!
@TH3DStudio
11 ай бұрын
Thank you! I hope the video helped you out!
@fredphilip822
Жыл бұрын
Great video and good instruction. What I noticed though, when I'm enabling the printer (Ender-3 v4.2.2 RCT6, BL-Touch 5-pin) and flash the printer with that fw, I don't have a software option for BL-touch probing the bed. And I can't get it going to set the Z offset (approx. -2.2mm). Do I miss here something or is that missing in den firmware?
@TH3DStudio
Жыл бұрын
Use the Level Bed option in the Motion menu. If its missing, its because the firmware wasn't configured correctly. There also is a BLTouch menu in the configuration menu as well.
@raynbow6
11 ай бұрын
Recently pulled my Anet A8 out of storage and trying to get it up and running. I have an auto levelling sensor SN04-N, is that covered in your firmware? It's been that long since I used the printer, although I updated to Marlin 1.1.9 at some stage, but as I've rebuilt it onto a metal frame, the sensor is in a different location and needs adjusted in the firmware, thought I'd give yours a try this time. Hoping the bootloader is there and lets me add the firmware easily 🤔
@TH3DStudio
11 ай бұрын
Not familiar with that sensor. You can probably make it work but can't be of much help.
@patissanchez
7 ай бұрын
Not having very good luck with VSCode, i don't have a blue bar at the bottom and it tells me to update my path on the very first line
@TH3DStudio
7 ай бұрын
You probably didn't open the firmware correctly. See here: kzitem.info/news/bejne/ynttyq2iZnWAi2U
@rafaelfernandes2134
2 ай бұрын
Hello, I have been using the firmware on my Ender 3 8-bit for some time and it has been working without any problems. However, now I need to increase the temperature above 260°C and I could not find the MAXTEMP parameter in the configuration.h file. Where can I change this parameter?
@TH3DStudio
Ай бұрын
Read the config file.
@KM4EBU
Жыл бұрын
Awesome Video, Would it be possible to make a firmware for the Longer LK5 Pro
@KyEvideos
8 ай бұрын
When selecting EZABL on CR-10 does Stock CR-10 Probe mounts and Custom Probe both hav to be selected? it doesnt flash when only selecting Oem Cr-10 mounts.
@y_noT42
Жыл бұрын
My visual studio doesnt have that blue bar at the bottom with the button to compile the firmware? Edit: bc i downloaded the wrong program hur dur om dumb
@LeftStepFPV
3 ай бұрын
What wrong program?
@chrisspatgen
Жыл бұрын
I am getting the following error #error "MOTHERBOARD not defined! Use '#define MOTHERBOARD BOARD_...' in Configuration.h. I have the Marlin V 1.13 board with the ATmega 1284P chip. Already performed the bootloader step. USB is on COM4
@chrisspatgen
Жыл бұрын
Never mind. Forgot to update the Configuration.h file and uncomment the Ender 3 line. When I did that the upload worked!!
@TH3DStudio
Жыл бұрын
yeah was about to say you need to uncomment the printer line. Glad you got it sorted!
@fredphilip822
11 ай бұрын
After using the firmware for a few month on a v4.2.2 motherboard I ordered a new motherboard v4.2.2.7 from Creality. When trying to compile the firmware for the new MB it's ending up with an compile error on module "Marlin/src/HAL/STM32/timers.cpp" with message "Default timer interrupt priority is unspecified or set to value which may degrade performance" . I selected in VSC the tab "Auto Build Marlin" the environment option "STM32F103RET6_creality" to compile. I assume that's a correct step to determine the processor of the new board. What did I do wrong here? Any ideas? Any suggestion is much appreciated. Thanks
@Damjanhd
5 ай бұрын
What about replacing and connecting SKR mini?
@TH3DStudio
5 ай бұрын
Hey there! If you need help we do offer tech support services. Just drop us a line here: tickets.th3dstudio.com/tickets/create/step1
@damiang3241
3 ай бұрын
Hey mate! I tried your tutorial. After all was complete all firmware files I get is .hex or .elf, no .bin file. Just wonder if there is something wrong I made :D My printer is CR-10 S5
@TH3DStudio
3 ай бұрын
If you're asking that question you didn't actually watch the full guide.
@amtpdb1
9 ай бұрын
I have tried this several times! Delete the programs and start over and over and I have yet to get everything to work. New windows 10,new downloads as you direct. The last several times I have gotten to where you said to click the build button. I have no build check mark and spent several hours searching build and nothing seems to help!!! Where and how does this program create the build icon? Thanks but I am stuck with a bricked ender 3 with a Arduino bootloader. Thanks
@TH3DStudio
9 ай бұрын
If you are missing the checkmark it is likely because you didn't follow the directions. See our video here: kzitem.info/news/bejne/ynttyq2iZnWAi2U
@amtpdb1
9 ай бұрын
@@TH3DStudio I thought I followed them to a Tea. I will try it again. Thanks 😕
@MrBrettStar
Жыл бұрын
Are there plans to further customise the advanced pause settings? When doing a filament swap to change colours the Hemera has a little bit of plastic that breaks off in the extruding gears when using the default settings which should be addressed
@TH3DStudio
Жыл бұрын
You can do that right now if you look in the configuration_adv.h file. That is were those settings are located. Our firmware is setup to cover general setups. If you have a custom setup (like the Hemera) then you will need to fine-tune the settings for your specific setup if the defaults are not optimal for your liking. We also have paid technical support available for people who want us to go over custom setups and are not sure where/how to start.
@JamiePancoast
Жыл бұрын
It's a nice concept but don't always work, at least in my case. Still looking for a BIN file that not there in VS
@TH3DStudio
Жыл бұрын
Then you are flashing for an 8-bit board. Please see the 8-bit board section in the video here. It's broken up into chapters for easy navigation.
@bornakreca2625
Жыл бұрын
i followed this video to the letter but after the build is finished, i dont have the bin. file
@TH3DStudio
Жыл бұрын
Are you on 32bit or 8bit?
@bornakreca2625
Жыл бұрын
@@TH3DStudio 8bit i did the 8 bit one too but the firmware dudnt upload to the printer
@TH3DStudio
Жыл бұрын
Then you upload over USB as stated in the video. BIN files are only for the 32bit boards.
@jpvanwoerden5215
11 ай бұрын
I couldn't find it for a Creality CR-10 Smart. Is the firmware also coming for this model printer? And do us this support the LAN port directly?
@TH3DStudio
11 ай бұрын
Due to the proprietary hardware in that machine we haven't done any firmware for it. If someone wanted to let us borrow theirs we could see if we're able to do anything with it.
@hawero4740
Жыл бұрын
thanks for the tutorial. I just installed a bl touch and the probe triggers but does not stop the z axis from coming down and crashing into the bed. I switched the black and white wires, tried different firmware, got new wires and manually triggered the probe but nothing seems to work. some people say I should define the sensor pins but I cant find that option in your firmware. any adive?
@TH3DStudio
Жыл бұрын
Its in the firmware if you read it.
@Runtthomas21
Жыл бұрын
I used a MacBook Pro 2020 everything went right until I put it in my printer it’s stuck showing the Creality logo I have an Ender 3 v2
@TH3DStudio
Жыл бұрын
Try formatting the SD card as FAT32 with a 8192 allocatiuon byte size.
@Runtthomas21
Жыл бұрын
@@TH3DStudio will try thanks for the response
@Runtthomas21
Жыл бұрын
@@TH3DStudio on MacBook Pro it doesn’t give you that choice just Ms-DOS FAT32 no other options with Fat32
@TH3DStudio
Жыл бұрын
I don't use any Mac computers so I won't be able to assist with that. You may want to google how to format SD cards for Mac OS.
@joachimbergsbakk9030
5 ай бұрын
When i tried to upload from VS code it says "Could not find one of 'package.json' manifest files in the package" what is wrong?
@TH3DStudio
5 ай бұрын
You opened it wrong.
@joachimbergsbakk9030
5 ай бұрын
@@TH3DStudio What do i do wrong?
@Stevens3D69
Жыл бұрын
hey man i need help i just bought a motherboard E3 Free-runs and they said it will work with my printer ender 5 plus do you have a video that will help me
@TH3DStudio
Жыл бұрын
This firmware works with it. Just need to replace the LCD with our kit as well. This cart link will add all the firmware and parts you need to do the conversion: www.th3dstudio.com/cart-share/qOlOm Firmware: www.th3dstudio.com/product/unified-2-firmware-for-creality-e3-free-runs-tmc2209-board/ LCD Kit: www.th3dstudio.com/product/ender-5-plus-12864-lcd-upgrade-kit/
@Stevens3D69
Жыл бұрын
@@TH3DStudio thank you so much man I have a screen already from my old printer it has the same numbers on it just from sunlu I ordered the dual LCD adapter and the firmware from you you rock
@CRUSTY09
Жыл бұрын
Great tutorial, very helpful. Question... After installing this firmware I am no longer getting complete bilinear grid outputs when running G29 (even while running with a verbose argument) in Pronterface. It seems to be a truncated output compared to the output I received with stock firmware. Is there a command I can include prior to compiling to increase the output? I'm always curious to see my bed mesh in a visualizer and the output with this firmware doesn't supply enough probe data points. Thanks
@TH3DStudio
Жыл бұрын
You may be running the wrong command for the visualizer since its a new marlin build. I assume you're using Octoprint so read their guide here: github.com/jneilliii/OctoPrint-BedLevelVisualizer/blob/master/wiki/gcode-examples.md The 1st example works for us on this firmware and our machines. G29 T after a G28 will output the grid data. Here is what mine output: Recv: Bilinear Leveling Grid: Recv: 0 1 2 Recv: 0 +0.707 +0.478 +0.138 Recv: 1 +0.324 +0.073 -0.341 Recv: 2 -0.034 -0.348 -0.776
@CRUSTY09
Жыл бұрын
@@TH3DStudio Ok, I see that my output from the auto level are too far out of range for the visualizer to read. 0 1 2 3 4 0 -7.738 -7.708 -7.760 -7.779 -7.785 1 -7.713 -7.710 -7.770 -7.785 -7.786 2 -7.768 -7.788 -7.863 -7.883 -7.876 3 -7.806 -7.833 -7.911 -7.890 -7.891 4 -7.858 -7.898 -7.971 -7.915 -7.905 If I replace all the 7's with 0's I can get a visualization to render. Any idea why my readouts are -7? I have my Z offset to at -4.9 and everything else seems in order. Not a big deal to alter the output, just curious as to why
@CRUSTY09
Жыл бұрын
@@TH3DStudio It also does not seem to be recognizing my Z offset. I configure the offset, run a tram sequence nozzle is in a good position all around. The next time I run a tram sequence, it is not taking the Z offset into account and the nozzle is 4mm above the bed....?
@TH3DStudio
Жыл бұрын
@@CRUSTY09 not sure with the limited information here. If you are a customer of ours with our EZABL you can submit a ticket here: contactus.th3dstudio.com/
@CRUSTY09
Жыл бұрын
@@TH3DStudio It's fine, the firmware just doesn't work as expected. I switched back to custom marlin firmware and everything works as expected. The TH3D firmware doesn't recognize the stored Z-offset (I tried for many hours, attempting every trouble shoot known) which is the issue with the bed level being so far out of range, and impossible to actually print with. I love the interface of the TH3D firmware, but if it doesn't work as expected, its just a polished turd. Hopefully this gets patched at some point and I can give it another try Ender 3 Pro v4.2.2. BL Touch
@dawidtram936
11 ай бұрын
Hello , I use your method for Ender 5 pro . All is ok but my ender doesn`t see BL touch. I made mistake or I buy wrong firmware?
@TH3DStudio
11 ай бұрын
You need to tell the firmware that you have a BLTouch and make sure to wire it to the 5 pin header if you have a 4.2.X board. support.th3dstudio.com/helpcenter/unified-firmware-bltouch-settings/
@elmarhusam6403
Ай бұрын
Hi. I need the Firmware for my HJC Maker 7. Do you can Help me?
@TH3DStudio
Ай бұрын
Dont have one for that machine.
@Oakengreenhill
10 ай бұрын
sorry to ask a noob question, i cannot find the configuration.h file other than in "stock marlin" folder in the list or just by looking in the folder?
@TH3DStudio
10 ай бұрын
Where did you download it from?
@Oakengreenhill
10 ай бұрын
@@TH3DStudio the link on th3d took me to github, i downloaded it from there, tried several unzip attempts but even in the folder the configuration.h file wasnt under the marlin section.. its odd as i used your software a year ago to flash a silent board without any issues. this got me stumped
@TH3DStudio
10 ай бұрын
@@Oakengreenhill the printer configs are no longer on github, you have to purchase those from our website. Just the core code is on github now. Head to uf2.th3dstudio.com to purchase the firmware for your machine. If you are new we'd also recommend getting the tech support option added on with purchase (its only $30 and thats support throughout the length of the subscription).
@Oakengreenhill
10 ай бұрын
@@TH3DStudio purchased, unzipped and just like That it loads, compiles and installs! literally took longer to unzip than flash :) i really hope those github links get removed. thankyou
@1managainsttheworld
Жыл бұрын
I would like to put this into my Ender 3 Neo. The question is how high can the bed temperature get? I would like to raise it to 110°C from the original 100°C, but I can't find any line in the code to do this change.
@TH3DStudio
Жыл бұрын
Our Firmware default is 120 for the max
@1managainsttheworld
Жыл бұрын
@@TH3DStudio Great, thanks for the quick response!
@foreignnwhipcrasher
5 ай бұрын
Thank you brother.
@TH3DStudio
5 ай бұрын
Any time
@SuperChopperpilot
5 ай бұрын
which one should you do if you have a CR-10S?
@TH3DStudio
5 ай бұрын
This one: www.th3dstudio.com/product/unified-2-firmware-for-creality-v2-x-boards/
@1213blech
Жыл бұрын
Hi, Iv followed the video and everything was fine I uploaded the firmware to my Ender 3 with an 8-bit board. I also enabled custom prob as I have the BL Touch kit from Creality, however I don't have any option to level the bed... not in motion or in configuration! The only options I have are Bed Tramming and M48 Probe test. Also when I Auto home it moves the X and Y axis to the end stops but for the Z axis it just moves up 3 times... Please help me out I have been at this for far too long and I can't see anything...
@TH3DStudio
Жыл бұрын
Level Bed is likely not shown due to the memory limitations of the old board you have. You can still do a level bed command by sending a G29 command to the printer. Also those boards are discontinued and we are no longer doing updates for them. We'd recommend upgrading to a 32bit board if you want to keep getting the latest updates and features.
@1213blech
Жыл бұрын
@@TH3DStudio yeah I ended up figuring out that I could level through the slicer! Any board u recommend? I’d rather get the best upgrade possible instead of just the next step up!
@thomasstichnoth8118
Жыл бұрын
I am not very talented in compiling the firmware. I have several problems with the settings, eg MinTemp error. Is there a possibility to download a ready firmware for an Ender 3 v2 Neo with CR Touch?
@TH3DStudio
Жыл бұрын
We do offer compile services if you get technical support with the firmware when you purchase it. We also have one-off help as well. Just send us a message at contactus.th3dstudio.com
@shadowdiver8446
Жыл бұрын
I have an Ender 3 pro, with the Touchscreen and 4.2.7 main board, CR Touch, and the Sprite Extruder Pro. I have an 8 gig sd card properly formatted, no matter what I try the machine will not take the firmware. I also have the 4.2.7 firmware from your website, any suggestions?
@TH3DStudio
Жыл бұрын
Try cleaning the slot and card. That usually is the issue: support.th3dstudio.com/helpcenter/fixing-sd-card-errors-sd-init-fail/
@ratajack1203
Жыл бұрын
Do you need to need to uncomment anything else to get the power loss recovery, because I’ve uncommented the line in the community features and it’s not working
@TH3DStudio
Жыл бұрын
You just need to uncomment it, recompile, and upload to the printer. It ONLY works over SD and only takes a snapshot every layer.
@CyberRedTeam
Жыл бұрын
How to fix this error when uploading the .hex "avrdude: stk500_recv(): programmer is not responding"
@TH3DStudio
Жыл бұрын
Either the COM port is tied up by another program or you have a board that doesnt have a bootloader installed.
@valorfam7836
7 ай бұрын
when i build it mine doesnt show a .bin file.... can you help me
@TH3DStudio
7 ай бұрын
We have tech support available here: contactus.th3dstudio.com/ $30/for one ticket.
@wescphoto
Жыл бұрын
I'm having a clue screen when flashing to my Ender 3 Neo. I think the first time I tried, I didn't set the right cpu and got a blue screen. I changed the cpu to match but its still blue screen. Not sure what to do.
@TH3DStudio
Жыл бұрын
Try flashing back to stock firmware and then updating again.
@wescphoto
Жыл бұрын
@@TH3DStudio thank you! I thought I really screwed up. Love the videos!
@wescphoto
Жыл бұрын
@@TH3DStudio Got it up and running but the knob isn't working on the lcd. If I press it the software restarts on the lcd
@TH3DStudio
Жыл бұрын
@@wescphoto you need to add #define SPEAKER_KILL to your config. This is in the directions if you read them.
@matiasmigo
Жыл бұрын
It does not detect the sdcard after installing the firmware for cr10s-s4. What happened ?
@TH3DStudio
Жыл бұрын
Not enough info here to troubleshoot your issue.
@manuelcastanon7531
Жыл бұрын
Hi, I need help. I installed VSCode and installed Platform IDE but I cannot open the configuration.h file. It tells me "the file is not displayed din the text editor because it is either binary or uses an unsupported text encoding" What does this mean and how could I fix this?
@manuelcastanon7531
Жыл бұрын
I have the aftermarket 4.2.7 silent board and purchased the firmware from your website, its just i don't know how to solve this problem i have
@TH3DStudio
Жыл бұрын
See here: kzitem.info/news/bejne/ynttyq2iZnWAi2U
@brianflynn7339
Жыл бұрын
Hello I am looking for the ender 3 pro with the blt and Sprite pro for the 4.2.7 board and have the v2 Display I am really new at this and need some help.
@TH3DStudio
Жыл бұрын
This would be the firmware you need: www.th3dstudio.com/product/unified-2-firmware-for-creality-v4-2-7-silent-board/ If you purchase the technical support with the firmware we can even compile and set it up over our email ticket system for you. :)
@brianflynn7339
Жыл бұрын
Ok I did and did not get a thing after paying for 53 dollars us will it take long to get a email or is it just PayPal slow
@keithstarling8244
Жыл бұрын
do you change for firmware now? you said free. it wants to charge
@TH3DStudio
Жыл бұрын
The older ones are free but we began charging for it back in August. It takes time and hardware to keep putting the firmware out. We have to cover our costs. One big plus about it though is you can add on tech support and get help with your printer setup and updates. We're also donating money to the Marlin project every month as well since we use their code as our base.
@ulisesteran1742
Жыл бұрын
hi dude, i have a problem, when i want to upload the firmware to my printer, the terminal show me this error: The terminal process "C:\Users\Ryzen\.platformio\penv\Scripts\platformio.exe 'run', '--target', 'upload'" terminated with exit code: 1. * Terminal will be reused by tasks, press any key to close it.
@TH3DStudio
Жыл бұрын
Sounds like you dont have the COM port set.
@sumyabaatar6628
Жыл бұрын
@@TH3DStudio hi i have a same issue i choosen right port but still showing this failture and im using adruino uno * The terminal process "C:\Users\Sumya\.platformio\penv\Scripts\platformio.exe 'run', '--target', 'upload'" terminated with exit code: 1. * Terminal will be reused by tasks, press any key to close it.
@ulisesteran1742
Жыл бұрын
@@TH3DStudio Ok, its all done, but the printer dont read de microSD
@mirkyd5944
5 ай бұрын
ENDER 3 ATMEGA1284P chip I flashed the bootloader on using the Arduino Uno as per your separate video tutorial and have disconnected the Arduino and then attempted to update the firmware using this tutorial however I am receiving this error message: Building .pio\build\melzi_optiboot_optimized\firmware.hex Configuring upload protocol... AVAILABLE: arduino CURRENT: upload_protocol = arduino Looking for upload port... Auto-detected: COM3 Uploading .pio\build\melzi_optiboot_optimized\firmware.hex avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x65 avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x63 avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x68 avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x6f avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x3a avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x54 avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x46 avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x20 avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x69 avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x6e avrdude done. Thank you. * [upload] Error 1 I've tried to follow the instructions to the letter I promise! I'd be grateful for any advice - thanks.
@TH3DStudio
5 ай бұрын
Hey there! If you need help we do offer tech support services. Just drop us a line here: tickets.th3dstudio.com/tickets/create/step1
@mirkyd5944
5 ай бұрын
@@TH3DStudio Hi, it will not allow me to create a ticket as I do not have a valid order number. Thanks.
@TH3DStudio
5 ай бұрын
You can purchase support separately. Just use the sales form. A basic ticket is $30.
@ruizjohn37
Жыл бұрын
do you have a video to help with the BL Touch
@TH3DStudio
Жыл бұрын
We do not have any BLTouch videos as thats not a product we carry. But we do offer paid technical support if you need assistance. Our firmware does support the BLTouch/CRTouch sensors. You can contact our support team here: www.th3dstudio.com/contact-us/
@barrygibson9854
Жыл бұрын
hi folks, thanks for all the hard work, i am however struggling with this one. i have a stock ender 3 neo and this firmware just wont flash for me, ive uncommented the ender 3 neo and then compiled and placed on sd card it but i just get a blank screen and then have to flash back to the stock firmware.....any thoughts?
@TH3DStudio
Жыл бұрын
You may need to compile for the GD32 CPU. Creality uses knockoffs on some printer boards.
@barrygibson9854
Жыл бұрын
@@TH3DStudio after manny many attemps it would appear to be uncommenting ender3_neo is the issue, if i select the ender 3 or ender 3 pro then it loads up fine, honestly have no clue why. mine is the newer neo with the built in cr touch and silent version of the 4.2.2 board if that makes any diiference or not i couldnt say. thanks again for all your hard work bro, us newbies would be dead in the water without you
@TH3DStudio
Жыл бұрын
Thanks for the info. I'll look into it. The NEO is the one that came with the weird red/black shroud on the hotend and a CRTouch preinstalled.
@barrygibson9854
Жыл бұрын
@@TH3DStudio yeah thats the camper. ive honestly just began this 3d printing journey and only started looking ot firmware in the last few days so unfortunatly i cant offer much insight for you but good luck my friend
@k-c4722
Жыл бұрын
@@TH3DStudio So I am having the same issue. Mine is a Ender 3 Max Neo, Idk if that changes anything. But nothing seems to load when I flash the drive into my printer. Any thoughts?
@Anonymous-b3m
7 ай бұрын
Have the Ender 5 Pro with CR Touch, but when I put in -5, -40, 0 for the offsets and try to auto level...it's alway overshooting the probe by about 10mm on it's first measurement towards the front left corner.
@TH3DStudio
7 ай бұрын
Could be improver offsets set or didn't actually flash on the board. Also could be a homing issue with the endstops as well. If you can't figure it out we do offer tech support.
@theveteranworkshop8328
Жыл бұрын
Where on the configuration.h file do I need to define the filament sensor? I cant find where it is to enable it.
@TH3DStudio
Жыл бұрын
We call our filament sensors the EZOut so you can look for that. If you have a printer that came with a sensor stock, just enable the printer and the sensor will be enabled.
@theveteranworkshop8328
Жыл бұрын
@@TH3DStudio I have an Ender 3 Pro and installed the creality filament sensor on it. Where would I enable it? Thanks for the replies!
@TH3DStudio
Жыл бұрын
The Ender 3 Pro didn't come with a creality sensor. That combination is not supported in our firmware but if you modify the source code you can get it to work as long as the pin for the sensor is set to the pin you have it connected to as well as the trigger logic for the sensor set correctly as well.
@paty.6667
Жыл бұрын
i have some question is bl/cr touch use the same config`?`
@TH3DStudio
Жыл бұрын
Yes
@paty.6667
Жыл бұрын
@@TH3DStudio thank you sir
@asinglegreatarmada1998
Жыл бұрын
One error and all of the following instructions are useless. I have an error that says include errors detected. Please update your include path. Squiggles are disabled. I have NEVER used the program. I apparently didn't make an error. If there's already an error, I can do nothing. THere is no mention of my Ender 5 in the version.h script.
@TH3DStudio
Жыл бұрын
You can ignore those: support.th3dstudio.com/helpcenter/vscode-squiggles-and-includepath-error/
@asinglegreatarmada1998
Жыл бұрын
@@TH3DStudio The Ender 5 is still not recognized. When I try to compile, I get an error that the motherboard is not recognized and "failed to parse Marlin features" I used a bootloader on this printer 2 years ago, so it should still be on there.
@rajkumarm2106
Жыл бұрын
I can't download my browser show 403 forbidden
@TH3DStudio
Жыл бұрын
You're probably in a country we block due to attacks. India, China, and Russia are all blocked from our main website. We had too many attacks and we do not sell to those countries so they are blocked.
@BlackopsSOG1
Жыл бұрын
what if i have a creality 4.2.7 silent board for the E3Pro?
@BlackopsSOG1
Жыл бұрын
nevermind there's a setting if you scroll down when youre going to download it that says "aftermarket boards" and youll find it in there, you have to pay $5 for it though since its "aftermarket"
Yes it is but you need our LCD kit: www.th3dstudio.com/product/creality-ender-7-12864-lcd-conversion-upgrade-kit/
@beratabaka3836
Жыл бұрын
hello your v4.2.7 files is non downloadable. 403 forbidden error. please fix thanks.
@beratabaka3836
Жыл бұрын
i have ender 3 v2 neo
@TH3DStudio
Жыл бұрын
You need to purchase them here: www.th3dstudio.com/product/unified-2-firmware-for-creality-v4-2-7-silent-board/ If you are still getting a 403 you may be in a country our hosting company blocks due to attacks. You can use a VPN to get around that.
@ruizjohn37
Жыл бұрын
i am not getting a .bin file any clue as to why ?
@TH3DStudio
Жыл бұрын
You probably have an 8bit board.
@ruizjohn37
Жыл бұрын
@@TH3DStudionvm i got it
@АнатолийПопов-й7ь
10 ай бұрын
there is no config.h in new version 2.79
@TH3DStudio
10 ай бұрын
Its called Configuration.h. All our firmware releases have it.
@anthonystanfield3143
Жыл бұрын
I didn't get a .bin file.... ?
@TH3DStudio
Жыл бұрын
You probably have an 8-bit board. Please watch the entire video, we cover both types and how to use the firmware with each board version.
@scottentwistle5793
Жыл бұрын
dont get the .bin extension using windows 11
@TH3DStudio
Жыл бұрын
Then you are probably compiling for an 8bit board. Re-watch the video section on 8bit boards.
@anthonyabt7637
Жыл бұрын
Not sure if it'll help, but the "little libraries" around the 7:30 mark. Make sure your antivirus isn't blocking these. This was my original issue and my computer tried using a different type of file to build the code on. I kept getting only hex and elf files. After adding the necessary website as an exception on my antivirus everything seemed to work just fine
@gufftek
Жыл бұрын
@@TH3DStudioi have the same problem right now but Im using a mini sk3 32bit... I've been stock here for around 3 months 😅😅
@TH3DStudio
Жыл бұрын
@@gufftekif you have our firmware and the tech support we can compile the firmware for you.
@Tinky432
3 ай бұрын
Bro just imagine charging 5 bucks for a firmware, thats bullshit
@DonTouch
Ай бұрын
Honestly it's messed up! False advertising aswell since they do intact charge for the stock board firmware. You got life screwed up if you think I'm paying monthly for firmware
@jho369
Жыл бұрын
CR10 V3 - After upload, it gave me an error 1. Edit: Looks like an important note is to close all Slicers that are connected to that COM. Upload successful! Question, after upload, how do I reupload if I make edits to the Config file? I kept getting errors about custom probe (I forgot to enable BL TOUCH)
@TH3DStudio
Жыл бұрын
Yes you need to have all slicers closed. Only one program can be connected to the COM port at one time.
@jho369
Жыл бұрын
@@TH3DStudio Thanks. Do you have a guild on how to do the BL Touch for my CR10 V3? Looks like I bought a BL Touch V3.1 so I dont know if it will work. It turned on but that's about it. It was working before. I have taken it off now for the machine to work while I do more research but I can't seem to get any info on this.
Пікірлер: 199