Have you worked with vapor polishing process for your project? How was the finish? What was your experience? Leave them in the comments below!
@stanaoves3943
2 ай бұрын
I have a large polycarbonate cover for a street lamp that I am currently restoring. Can I use ordinary acetone?
@justinssleeyt
Жыл бұрын
This video was very well done. thanks for the introduction to this process!
@starrapid
Жыл бұрын
Thanks for watching :)
@MrNoipe
Жыл бұрын
Very educational video. The results are pretty astonishing.
@noviceartisan
Жыл бұрын
Acetone makes a good substitution for ABS and PEI :)
@lucysluckyday
Жыл бұрын
I'm sold !! That was a seriously impressive demo.
@mwsiviero
Жыл бұрын
Very nice! Thanks from Brazil
@starrapid
Жыл бұрын
Thanks for watching :)
@JohnJones-oy3md
Жыл бұрын
1:40 - Whoa. 👀
@starrapid
Жыл бұрын
Exactly. This is a great process.
@SadshiEisenmann
Жыл бұрын
Really nice, saw some videos before. We do plastic surface restorations for many years (cable cars, gondolas etc.) Where can we buy the equipment in Europe? Does it work on stage (portable) outdoor? Thanks for the informations.
@bob_mosavo
Жыл бұрын
Thanks 😁
@starrapid
Жыл бұрын
👍
@sunarf
Жыл бұрын
This works on PE (polyethylene), but will it also work on PETG (polyethylene terephthalate glycol)?
@БабурЮсупов-э9ф
Жыл бұрын
does it work with nylon
@DL-fi5cc
Жыл бұрын
Very interesting. Is there a similar method that could be used with polyurethane resin like or including smooth on crystal clear? Could save me a massive amount of multi-stage hand polishing. Thanks for another great video.
@JaydenLawson
Жыл бұрын
Yes
@michaellambert7567
Жыл бұрын
To protect against Methylene Chloride, the NIOSH Chemical Pocket Guide only recommend respiratory protection in a supplied air mode. Therefore, there is no cartridges suitable for an application where Methylene Chloride is present. soooo, what cartridge are you using? What is the "positive air pressure "system the technician is wearing? Thanks.
@randallsemrau6911
6 ай бұрын
He's not.
@scottrowe726
3 ай бұрын
yes, very clearly a completely uninformative, and even dangerous, clickbait video
@user-ve5gp8iy1c
9 ай бұрын
沒有比較快 沒有限制出錯想必會很多
@bolddenis4198
6 ай бұрын
What grit sandpaper is best suited for this kind of polishing?
@joesshop3622
5 ай бұрын
2500 to 3000 and then polish. The further you go up in grit the easier it is to finish and have it look perfect. Also if you start low like 220 grit, each progressive grit MUST be stepped up in small increments. Don't want to skip grits to find out in final polish you can still see rough sanding marks from advancing to rapidly. Use a mister and some water with one or 2 drops of Dawn dish washing soap to keep your sandpaper clean and your material from burning as paper typically loads up without it...
@vanillaexplosion99
5 ай бұрын
@@joesshop3622 I polish under the water tap with water flowing, this works quite well.
@joesshop3622
5 ай бұрын
@@vanillaexplosion99 Most certainly, I mention the mister for applications that cant be soaked or are simply "at the bench friendly lol"
@jamescalkins8803
Жыл бұрын
Looks like methylene chloride (dichloromethane). Simple enough.
@starrapid
Жыл бұрын
👍
@jamesdolph437
Жыл бұрын
now to work on my poly carbonate glasses
@user-du8px2wu2x
Күн бұрын
Must wear positive pressure mask…and yet the video shows a person doing the process with a regular organic filter mask. Hahaha
Пікірлер: 32