just discovered rotten areas in the transom of my boat rebuild (sounded solid a few months ago while it was wet but has since dried out inside my shop and now it is definitely a hollow sound) this video is going to come in handy now.
@marcuswormald9291
2 жыл бұрын
Got same problem, howd you fix yours? Is planning on putting steel plate in
@edwinarce4937
6 жыл бұрын
thanks for the video. I had to change that part of my boat and I did it myself thanks to your video
@ryanmiddledorf3648
2 ай бұрын
Hello there. I have a 1977 24ft Nisqually with a 5.7, 280 out drive. It’s not picking up water through muffs. I pulled the water pickup hose from where it connects to the outdrive and put my water hose into it feeding up to the pump up in front of the engine. That works as it should with no overheating. My question is; from where the hose connects to the outdrive, down to the water pickup holes in the lower unit. Is there a pump/impeller or other mechanisms that could fail causing water to not go up to the hose?
@Mr_Chris
6 жыл бұрын
Thanks for the vid - Just doing mine now.
@Billy982810
5 жыл бұрын
Great video boss. big help.
@paulgibbs478
3 жыл бұрын
Really great video, just letting you know those hooks you were talking about, they stop the leg from jumping up when you put it in reverse
@truthhunter4270
6 жыл бұрын
Excellent video, very helpful! I have a hole in my drive bellows and it’s leaking a steady stream of oil. Any idea how oil is getting in there? Is there a gasket seal or a O ring in there that could be blown. Thanks! I had it out on the water so the oil is milky looking, hopefully it didn’t cause to much damage.
@grumpypapaw3228
5 жыл бұрын
Mine leaks oil as well, but only very little. I may have to rebuild the upper unit on the sterndrive to fix the leak. I might try to rebuild it this winter. I'll be sure to make a video.
@MediatechLtd
4 жыл бұрын
I have the same issue. Did you find out the problem?
@brianwright4104
4 жыл бұрын
Hi I've done engineering in some very bad corrosive places that white powder is aluminum oxide salt corrosion on aluminium for your bolts use Anti seize copper coat is good or a marine version and the chips in the paint i would dill wire brush them and treat with salt away and used a white ceramic paint for touch up and new tec body filler sets like steel and has fiberglass in it
@robne6712
2 жыл бұрын
you can also sand it, spray with krylon etching primer, paint with a enamel spray and clear coat it.. all rattlecan..
@grasscutter88
11 ай бұрын
Doesn't that steering pin pivot when the drive turns? I don't get how they get so stuck
@David-zw9uz
6 жыл бұрын
the reverse linkage is so when you reverse the drive will not fling up
@grumpypapaw3228
6 жыл бұрын
That makes sense. I thought it might have let the drive come up if you hit something underwater.
@jameshuban6515
2 жыл бұрын
It is also the locking mechanism for the outdrive tilt. It is a handy way to access the exhaust bellows and raw water intake clamps as well as the shift cable bolts.
@bp4053
2 жыл бұрын
how do you remove the next part (that's half in, half out of the boat)
@jbangun1682
5 жыл бұрын
I pulled out my uni joint bellow and there was some water that came out. Roughly about 100-200 cc. That's not normal, is it? There shouldn't be any water in it, right?
@grumpypapaw3228
5 жыл бұрын
Was there a hole in the bellows?
@jbangun1682
5 жыл бұрын
@@grumpypapaw3228 Haven't pulled it out yet. Was cleaning the uni joint. Think I will just change it.
@steven_inlines3503
6 жыл бұрын
What is the name of the part that you press at minute 21:20?
@grumpypapaw3228
6 жыл бұрын
Reverse linkage
@waltervk
5 жыл бұрын
reverse lock
@1bad67stang
6 жыл бұрын
JC, How much time are we going to waste just focusing on some little plug?!?!?! Good Grief. Stick to the mission and FOCUS!
Пікірлер: 26