"Texas", your compassion for metal work really shows, your skills are catching up inclusive of your camera and editing / content...tanks for continuing sharing
@CTmoog
Жыл бұрын
Thank you! I do enjoy the metal work. It can be a bit scary at first but I think I'm starting to get the hang of it. =)
@SladesVWBeetle
Жыл бұрын
Outstanding CT!! You and Jason are both on the metal work!! What you’re doing is pretty serious fab work!!
@CTmoog
Жыл бұрын
Thanks man! I appreciate that! =)
@elaineferreira2980
Жыл бұрын
perfect. the seam you made where the glass goes, simply sensational, I never get tired of watching your videos. real surgery. great job CT. 👏👏👏👏👏
@CTmoog
Жыл бұрын
WOW! =) Thank you! =)
@Darryl603
Жыл бұрын
Looking good, CT! Getting there...
@CTmoog
Жыл бұрын
Thanks Darryl! 👍
@everydayrenaissanceman2246
Жыл бұрын
Heck yeah buddy! That looked really tough and as far I could tell you did great.
@war7334
Жыл бұрын
You have good metal working skills and your work is meticulous.That window will fit perfectly.
@Jake-ix1od
Жыл бұрын
I’ve spent countless hours, researching ways to remove the death foam from my 73 sports bug. I’ve been considering removing sections of sheet metal to make easier access; welding the sheet metal back in place after removing the death foam and thoroughly cleaning the cavity. My beetle is a family owned California survivor and it’s currently in dry storage, so I’m not too worried about severe rust, but I need to take measures to prevent it. My gratefulness to anyone willing to share their wisdom and knowledge with me, please! I’m a newbie with automotive restoration.
@christopherbrown6697
7 ай бұрын
I'm planning on cutting access panels from the inside. I'll flange the edges and make covers plates from the same area of a parts car, then drill and dimple holes for countersunk screws. That way I can have access from behind for any bodywork and foam remediation and can paint, treat, even place some sort of non-absorbent substitute for the foam if desired, and nothing will get burned or melted from welding it back together in the end.
@ShellBella1012
Жыл бұрын
I love watching the progress of things.
@CTmoog
Жыл бұрын
Thank you! =)
@helgedell
Жыл бұрын
Great. About time you drive a vintage VW product as a daily driver soon, probably beeing the biggest VW collector in your area. :)
@CTmoog
Жыл бұрын
Yes, hopefully soon! =)
@Johnditit
11 ай бұрын
You got my attention! I've been watching your videos for a few days now. I have a 65 that I'm going to be redoing for my daughter. Your skills are mad! Keep it up. Oh I believe VW put that foam in the window corners to keep exhaust gasses from entering the interior spaces. I know it has its dark side, but they had a pretty good reason. I don't think you will have an issue with it as long as your exhaust is in good shape and most should vent out the louvers anyway.
@tKetcham1
Жыл бұрын
Try practicing laying down a continuous bead instead of hundreds of tacks. I understand that you are trying to be careful, but a continuous need will not only look better, but it will be a stronger more reliable weld Also, tacking the part down is to keep the part from pulling away from the work as you weld from one end to the other. In this case tacking each end and also in the middle both inside as well as outside would be sufficient to stabalize the work so you could then lay down a nice continuous uniform bead. Once grinded you can't see the difference, but every time you stop and start the weldyou are causing a weak spot in your weld. Your weld if done properly should have the appearance of a leaned over roll of dimes. What you've got, (no offense) looks like goat pellets, and I'm not talking about what they eat. I applaud you for learning as you go, but take a moment to watch a skilled welder or two on KZitem demonstrate a good bead and listen when he explains the purpose behind tacking the ends first. You shouldn't start from one end and tack every inch or two until you get to the other end. That defeats the purpose. By the time you get to the other end, the price gas heated, warped, and pulled away from where you had it positioned. Tacking each end first will stabalize the part to the work so that warping is minimized.
@markj.7369
Жыл бұрын
Way to go CT. Glad to see you pushing forward on completing this project. Cant wait to see you driving it. God Bless friend
@CTmoog
Жыл бұрын
Thats the plan Mark! Thanks buddy! 👍
@maxwellharmon4172
Жыл бұрын
DUDE !! YOURE KILLIN IT!! this video is awesome! your fab skills are getting really good. I feel like im learning a bunch from you
@CTmoog
Жыл бұрын
Thanks man! =)
@5150mxVW
Жыл бұрын
Nice repair, that was tough with the vents! Like the others I just wanted to say I would of used the coat hanger technique, even though I have no flippin' idea wth that is 😆
@CTmoog
Жыл бұрын
Thanks buddy! You're getting there. 👍 Bad Chad does it all the time. I couldn't find a coat hanger! =)
@jeffclark3924
Жыл бұрын
CT the metal surgeon, you rock!
@CTmoog
Жыл бұрын
Thanks Jeff! =)
@stewkeene
Жыл бұрын
Fun times my friend, smart move cutting out those pieces. That has to save you a LOT of fabrication time 🫵🏻👍🏻
@CTmoog
Жыл бұрын
Thanks Stew👍 Yes, it saved a ton! I was considering doing it but I'm glad I didn't. I think it would have opened all kinds of problems.
@danielhelbig1116
Жыл бұрын
You’re a legend, I love this project
@CTmoog
Жыл бұрын
WOW! =) Thanks Daniel!
@SanDiego_VDubLife
Жыл бұрын
There you go CT. Making progress on one project. Slow and steady wins the race. Consistent. I hope to start trying my hand at welding this summer!😊
@CTmoog
Жыл бұрын
Thanks my friend! =)
@MrGustavothai
Жыл бұрын
this is the dream patina! I love this redish tones of oxidation. Mine has patina, but not like this. Iv sanded with 1200grit and did some clearcoat all over.. looks amazing
@CTmoog
Жыл бұрын
Thanks man! Yes, I'm trying to preserve as much as possible. It's not easy with all the metal work that needs to be done but I think we can save most of it.
@MrGustavothai
Жыл бұрын
@@CTmoog its looking awesome already... keep on moving! amazing work. Ill definitly watch it till its done.
@justinsmith847
Жыл бұрын
Oh yeah another beetle video hello CT !!!!!!!!!!
@CTmoog
Жыл бұрын
Thanks Justin! =)
@justinsmith847
Жыл бұрын
@@CTmoog you got it man
@Mikefngarage
Жыл бұрын
very hard piece to put in. Great job
@thisoldwatch9944
Жыл бұрын
Well done can’t wait for the next episode 👍
@CTmoog
Жыл бұрын
Thank you!
@Raxsal
Жыл бұрын
Man it looks like brand new! Perfect work! 👍
@cattlerepairmancattlerepai9414
Жыл бұрын
A grinder and paint - make you the welder you ain't! That is my motto for body panel repair! Your graft looked good there in the end.
@richardwylie07
Жыл бұрын
Looking forward to you getting back on the Ghia.
@deanage1983
Жыл бұрын
Yay another beetle video 😊😊
@CTmoog
Жыл бұрын
Thank you! =)
@Biokemist-o3k
Жыл бұрын
CT, I have a Porsche 914 with its engine and trans that was good when it was parked. A young girl had the car and parked it in her father's barn when she got married. Years went by and the farm was sold. The new owners did not want the Porsche which was in pristine shape and pushed it out of the barn into the paddock. They moved it around a few times before I found out they had it. Somehow they dented every quarter panel. You know that they had no rust protection so the tin worm started its brutal business. When I found out about it (3 or 4 years later I believe) I made arrangements with the people to purchase it I have had it on my dad's trailer for the last three years as I have been recovering from getting hit on my 1957 Harley and nearly having my right leg taken off as well as learning how to walk again and fighting off the blood clots that went from my leg to my heart and lungs making me feel like I was drowning every time they closed off my ability to assimilate blood in my lungs. When I got the hospital the surgeons said I had less than six minutes if I did nt go right into surgery.I am doing much better and can walk without assistance. My dad wants his trailer back and I do not have a place for my beloved Porsche. I am coming back down to Florida in a few months to stay hopefully but I would like to find a good home for my beloved yellow 914.Do you think we might be able to work something out as either a collaborative venture or possibly you might want it. Your brother has that awesome place you do your builds in. I know that it really sucks to work on stuff alone and I would love to join forces and do some great things. message me and I will give you my number . I have a full mobile welding operation with an extra Miller Roughneck 2e that is an AC welder that I have DC conversion kit for. I have almost a full machine shop and will have a full machine shop soon We need to talk. Thanks-John P.S. I have a lot of glass for many years of bugs including wheel spacers and conversion 4 lug to five lug kits including an air-conditioning kit with a dashboard for a bug or a Kharmann Ghia.
@cbody70
Жыл бұрын
Nice job on the window patch. Check out the "coat hanger" technique to fill large gaps Bad Chad used recently on his Hudson project.
@CTmoog
Жыл бұрын
Thanks man! I will do that! Bad Chad is awesome! =)
@snowdogs59
Жыл бұрын
I am enjoying watching you and Jason learning metal working at the same time. You guys should get together and take some lessons from Larry and/or Mike F. Onward!
@CTmoog
Жыл бұрын
Thanks man! Yes, it's great to have guys that are willing to share their knowledge with others. Larry, Mike, Darrin and so many others putting it out there. It helps everyone grow! =)
@backyardkombi5466
Жыл бұрын
Pretty complicated job there and looks like you pulled it off admirably.
@CTmoog
Жыл бұрын
Thanks buddy! Yes, it was a bit of a challenge!
@davidadams007
Жыл бұрын
Getting stuck in! looking good and solid.
@CTmoog
Жыл бұрын
Thanks David! It turned out ok. =)
@PapiDoesIt
Жыл бұрын
That fit much better than I thought it would, seeing as how the windows are different heights. It's going to almost look too good to keep the patina.
@richardmethot1317
Жыл бұрын
Massive undertaking ….. can’t wait to see the completion
@brianbloom1799
Жыл бұрын
VW was 1 of my Best cars, I restored a 65 Convertible back in 1980, It came out Beautiful, I payed 150 dollars, I was a body man for Mercedes Benz When I was done I drove the car, for 2 years and sold it for a 68 dodge charger rt 440 4 speed, The Man that Bought the car Took it to have it checked out by VW they Told him the Motor ran like Brand new ,I puy a complete new floor pan it Actually had working Heat, What a great car for snow, , If ct Stands for CT that's were I live, Danbury at the Time, Good luck with your Build, Hope it turns out to be everything you Hoped for GOD Bless
@mikelove9832
Жыл бұрын
Its Awesome how farr you have come ! Thanks Straight Ahead ✌😎
@georgeclements2742
Жыл бұрын
Just two suggestions. First, I think that you would have saved yourself a lot of trouble if you repaired the replacement patch before welding it into the car. Second, I suggest that you make a template of the whole window aperture before cutting out the other corner: that will make it easier and more accurate to align the replacement corner after you cut it out. Thanks for the videos and best wishes.
@CTmoog
Жыл бұрын
Thanks for the tips! I like the idea of making a template before cutting. I wonder if I could make one out of tape on the good window and transfer the lines onto the rusted window... um....that might work.
@christopherbrown6697
7 ай бұрын
I've made a plywood template for a flat window on a bus. It could either be screwed to the pinchweld or you can make a serious of holes with a hole saw to feed clamps through. When I added an extra Westfalia jalousie window to the right rear section of my '74 bus, I cut a donor section from a sliding door to change the asymmetrical rear side window to a rectangle. I trimmed away the curved rear section of the window, screwed the jalousie window to the pinchweld of what remained of the window opening, then screwed it to the donor section, using the actual window as the jig to tack it in place, a perk of a metal-framed window.
@christopherbrown6697
7 ай бұрын
Correction: left rear jalousie, driver side.
@hasbeengood
Жыл бұрын
Cool! Same color, don't even need to paint it! LOL Nice job!
@CTmoog
Жыл бұрын
HAHA! =)
@anibalbabilonia1867
Жыл бұрын
Man CT! I gotta handed to you! That’s some impressive metal work there! Specially when dealing with metal trim around the window trim! 😮wow! Great job overall! Looking forward to seeing the next chapter!👌😎👍
@CTmoog
Жыл бұрын
Thanks man! =) It was a big challenge. It could have gone real bad....but I got lucky on this one. =)
@--RO--
Жыл бұрын
Really good job. I admire your determination -
@anthonylatronica5108
Жыл бұрын
For the wider gaps use a coat hanger to fill in the gap. Secondly I would have left more material at the top of the louvers. You created a very tough scenario by cutting so close to the louver itself
@CTmoog
Жыл бұрын
Yes it was a bit too close...
@chris8405
Жыл бұрын
@@CTmoog If the louvers are even slightly distorted by heat, or get any weld splatter onto them it will be very hard to make them look right again. I would have left at least half an inch of metal above the tops and tried to cover the louvers to avoid splatter. Hope you get lucky. Otherwise really enjoyed seeing the results of your work.
@dolf1010
Жыл бұрын
Great job ! 👍 Thank's for the video .
@CTmoog
Жыл бұрын
Thank you! 👍 =)
@vwcoco
Жыл бұрын
Nice work Ct 👍
@CTmoog
Жыл бұрын
Thanks Andy! 👍
@toddjohnston4788
Жыл бұрын
Wow didn't know that windows were that bad 😳..you did a great job 👏 doesn't matter what the welds look like CT They grind down...just have to make sure no holes or warping 😢
@franciscopinho9997
Жыл бұрын
I really believe you has improved your metal work skills. And I wish you keep on the path and evolve all about it, because I can see this future.
@vayabroder729
Жыл бұрын
Talk about precise surgery! You cut it really close! That foam inside always rusts everything out in those more modern models. Somehow my impression was that bodies were the same from ‘58 to ‘64 and then ‘65 to ‘72. If the ‘73 is the same you got lucky. When you reinstall the glass make sure you use black butyl sealant inside the new rubber seal channels. That way you prevent that rust there in those window channels and especially that rear package tray. We’re getting there; like you say 😉👍
@CTmoog
Жыл бұрын
Thanks man! Yes, I guess the rear wind is the same from 65 to 71. It got taller in 72 but the bottom section appears to be the same size.
@vayabroder729
Жыл бұрын
@@CTmoog Yes sir; you got lucky but hey! You’re getting into Mike F’n territory in terms of patch complexity 🤣😂. You’re doing great 👍
@MPi-KM
Жыл бұрын
The CT drinking game. Everytime he says "alright guys, we're getting there" you have to take a drink.
@type2523
Жыл бұрын
Can’t wait for the repaint video
@leudissantana
Жыл бұрын
Excelente trabajo maestro.
@shrikantsarsar
Жыл бұрын
Hi CT Great Work Not Bad CT Keep Going CT Perfect Work Done And It Will Look Great After The Final Work Done Super Work CT Nice 👌👌👍
@CTmoog
Жыл бұрын
Thank you!!! =) 👍
@iapologizeinadvance4812
Жыл бұрын
Great job - you sure have come a long way!!!
@gabrielantoniomartin7995
Жыл бұрын
Cómo siempre excelente trabajo amigo Saludos desde Argentina
@CTmoog
Жыл бұрын
👍😎👍
@grantdw236
Жыл бұрын
awesome work man lovin this build
@CTmoog
Жыл бұрын
Thanks man! I really appreciate that!
@fredericvaneyll2281
Жыл бұрын
Hello Nice job ...from belgium
@CTmoog
Жыл бұрын
Thank you! =)
@darkfactory8082
Жыл бұрын
Hey there, Mr. CT.. Tricky, ah? Hehe.. You cut soooo close to the louvers (grilles) it became difficult to weld.. One tip - when welding, try to cut on a good spot, which is accessible for later planishing work.. Avoid cutting next to corners or other difficult parts. Also I see rot damage to the border of the window, which you need to have smooth and precise as it's the thing on which the rubber seals. Well, if things go too south, then you have still the option of modifying the seat and use some polyurethane adhesive, but that's another story. Defective or plasticised rubbers are also mostly the cause of window channels rot, because those retain water in the channel. Other than that, I'm glad to see you making some serious metal work. Don't loose too much time in fiddling with the patches, just cut an approximate dimension a bit bigger than the hole, mark it on the car, dress the hole according to the marking, insert the patch and "glue" it. 😁It's easier. Cheers, keep on!
@robertferrell8518
Жыл бұрын
The way you’re doing it now you’ve got to worry about all kinds of warpage and distortion onto mention affective penetration at every one of those vent louvers!!
@bigbuck1318
Жыл бұрын
Little intense cutting close to the vents. But you’re doing good.
@CTmoog
Жыл бұрын
Yes it was a bit to close... =) Thank you!
@Oscarito_gamer_divertido
Жыл бұрын
@@CTmoog por que. N O terminas uno primero.
@ATOMSHAMRADIO
Жыл бұрын
Looking good CT😮👍💯
@CTmoog
Жыл бұрын
Thanks Atom! 👍
@pfdmustang
Жыл бұрын
I was conserned with you welding that close to the vent holes but after you cleaned up the welds it does not look that bad. I bet with a little clean up with a round file you can get them to look factory.
@CTmoog
Жыл бұрын
Yes, I know it was too close. I should have gone up just a bit. Yes, I think it will clean up ok. =)
@enriquelopez9124
Жыл бұрын
Awesome job 👏 👍🏿
@ricardolopezgutierrez1989
Жыл бұрын
Saludos de Mexico CT
@melissamotamorales7183
Жыл бұрын
excelente trabajo maestro.....
@georgemckee5997
Жыл бұрын
Great job 👍
@kajuncourier
Жыл бұрын
Use coat hangar metal to fill in welding gap. That is what "Bad Chad" youtube car restorer does.
@neil6212
Жыл бұрын
Not being as good at body work as you have become over the past few years, I would have removed the entire area around the window, which should have insured the glass would fit. That leaves you with some butt joints to weld. Since you already have a panel flanger/punch, it would be easier to make a lap joint, which is easier to finish. Yeah, I know that's the easy way out, but I'm an electrician not a metal worker! I used the flange method in replacing the entire roof line on a Gremlin. In that case, I joined it at the area aft of the B pillar. The original joint was welded and finished with solder. Mine looked OK, but wasn't really as pretty before filling and paint. You have learned some amazing skills, and are willing to attack projects which I wouldn't have done in the middle sixties.
@re-fix9678
Жыл бұрын
good
@tomasgilhernandez
Жыл бұрын
As always, doing an excellent job of welding, and I ask, why didn't you cut the entire back part where the grilles are and take advantage of it to clean the part that does not have easy access both for cleaning and painting, and likewise you would have cut the entire back of the donor car and thus remains in one piece since it looks like it is in good condition? Greetings from the Southeast of Mexico. Blessings.
@TheOzzyOzan
Жыл бұрын
1 quick question: why didn't you replace the whole rear window+vent with the one from the donor car?
@SuperUncleRyan
Жыл бұрын
That is exactly what I would have done. The best way to avoid any issues with fitting the glass later.
@CTmoog
Жыл бұрын
Hey Ozzy, for this project I'm trying to retain as much of the original "rust" patina as possible. Also, there are a lot of welded sections that hold everything together. It would have opened a whole bunch of can of worms if you know what I mean.
@user-yv5gg7vr8v
Жыл бұрын
Отличная работа! Спасибо большое за ваши видео!
@small-china
Жыл бұрын
да ну нафиг. чувак жопорукий, почти как я )) смотрю это, только чтобы поржать. на самом деле он торопится. можно сделать с меньшими потерями.
@CTmoog
Жыл бұрын
Thank you! =)
@markandrews7043
Жыл бұрын
wow well done bro
@richardhill4862
Жыл бұрын
Thumbs up sir!
@CTmoog
Жыл бұрын
Thanks Richard! =)
@robertnauss4815
Жыл бұрын
For gaps use coat hanger told ya this before ..Bad Chad technique
@CTmoog
Жыл бұрын
Yes, I've seen him do that. I was looking for one in the shop but couldn't find any.
@johnc.fonseca8961
Жыл бұрын
Not easy work, but you done great. Keep CT
@CTmoog
Жыл бұрын
Thanks John! 👍
@oldbugadventures
10 ай бұрын
I got that same gab in my back window.
@patrickbrown3135
Жыл бұрын
Lookin' good 👍
@CTmoog
Жыл бұрын
Thanks Patrick! 👍
@TimsWorkshopTJY
Жыл бұрын
Hi CT, good work on that side so far. Like you said as long as the window fits all the rest is how you get there. You need to try Mike overlap cut and weld the gap trick. Probably not on this but a larger area when you get to one. try it out on your parts bug for practice
@terryraymond7984
Жыл бұрын
lookin good
@jimpatnode4445
Жыл бұрын
Hows the dragon coming? Finished casting the engine block yet?
@CTmoog
Жыл бұрын
Hey Jim, VW Darrin built the 360 FE engine and it's 90% done. Waiting for a few small bits. The frame was blasted and painted. Lot of parts needed to complete and $$$...Have enjoyed the Beetle build? I've really been learning a lot on this one.
@julianroberts7116
Жыл бұрын
Hey mate you're doing great. I was watching through my hands though, when you welded that corner in - you were so close to those vents!! Did you consider cutting out the whole rear window from the donor, say an inch or so around, then just cutting the 3 inches from its height? You could've fixed the whole thing in one go, and got rid of all that rusted metal on the lip. You could've even taken the vents - cut right down the the top of the engine lid and taken the vents from the donor as well. However the rust and patina on the '65s vents are lovely - maybe it was best to keep them.
@robertferrell8518
Жыл бұрын
Whatever happened to the weld through primer on the backside and spraying rust converter on the inside of the cavity that you opened up??????.
@CTmoog
Жыл бұрын
I will spray everything inside once it's all welded up. There is plenty of access through the vents and inside the roof line. Makes a cleaner weld without all that stuff on it. Best to spray it after if you have access.
@terryraymond7984
Жыл бұрын
As long as youre window still fits I see an old Window seal there on the top so it seems you might be checking that
@CTmoog
Жыл бұрын
Thanks Terry! Yes, it seems to fit ok.
@garymallard4699
Жыл бұрын
I would cut your patch panel over cutting that close to the grilles.... less chance of disaster or some warping.... leave as much metal as you can away from something that detailed... alot less finish work later too and easier to sand/grind if you have your joint farther away.. and put those repair pieces ( small rust areas and gaps ) in before you weld this piece in...again it is easier to do when it is off vehicle and you can add the metal and trim it easier ...
@andrewboyd9946
Жыл бұрын
I think you can do the same with the swamp dragon!
@CTmoog
Жыл бұрын
Hey Andrew, I feel like I'm getting there! =)
@dogit1840
Жыл бұрын
Inbetween welding runs wire brush clean the welding tip any material inside the welding tip distorts decontamination field of the argon gas
@robj2704
Жыл бұрын
Looks like that '73 has been driven into the ocean at some point in its life.
@CTmoog
Жыл бұрын
Hey Rob, Yes I think so.... =)
@front2760
Жыл бұрын
Nice work.But all those tacks?Tad more heat i think would of helped.
@terryraymond7984
Жыл бұрын
W hile welding why do you use a short wire (on the tip of the tig welder)?
@AlbertRavoir
Жыл бұрын
You should have taken the full bottom with the grid since the size is the same. Or there is something preventing this?
@dgadver
Жыл бұрын
Hi CT! What ever happened with your Karmann Ghia? I thought I saw her for a second. Great videos!!! Dave
@elobiretv
Жыл бұрын
When cutting it to size, cut less off and trim it in bit by bit with a grinder otherwise you'll over cut and end up with huge gaps like you had at the top. Also would have primered inside while you had it open
@earlt_vw
Жыл бұрын
Nice work CT! What settings are using on your welder? Are you using .030 or .035 wire? Thanks!
@TheOriginalLugnuts
Жыл бұрын
Why not cut the whole base of the window including the vents sense you have to fix both sides?
@CTmoog
Жыл бұрын
I considered that but there are too many weld points that connect to a ton of other sections that would have opened pandora's box...
@TheOriginalLugnuts
Жыл бұрын
@@CTmoog okay gotcha.
@claudiojoseeliasde3oliveir413
Жыл бұрын
Bom dia serviço tá ficando melhor do que encomenda
@carlanderson6629
24 күн бұрын
Condition of the 73 body looks better than the 65.
@andyp.1102
Жыл бұрын
Servus CT, what do you think of replacing the tailgate?
@evasesh6585
Жыл бұрын
Im just wondering why you didnt just cut out the entire window from the parts body and weld the entire thing in the one you are working on. Looking at it, it may have been easier and fixed a lot of the pitted seams on the rest of the window.
@terryraymond7984
Жыл бұрын
sorry I meant to say mainly Parts Place may have *used* bug cabs possibly their price might be high though.
@ygaillard38
Жыл бұрын
Bonsoir une amélioration des soudures par points très bien mais pour une greffe de précision d'une partie de la lunette arrière il vaut mieux utiliser un poste argon pour réaliser des soudures précises en continu sur de la tôle peu épaisse CT préciser vôtre profession si cela vous dérange pas merci
@maverick4177
Жыл бұрын
That’s going to look like a bodge imo
@dogit1840
Жыл бұрын
Stop thinking about what we think do your thing
@pedrokd5439
7 ай бұрын
Give the engine to your local technical college, and the apprentices could learn from its basic construction.
@robertferrell8518
Жыл бұрын
Hate to say it, but I think you just screwed the pooch!! It would’ve been a lot easier to cut it all the way down to the rear hatch seam , and use the vent louvers from the donor car!!!! That way you would’ve had a lot more metal to work with and also to make a better weld!!!
Пікірлер: 173