Thank you! I just ordered replacement blades for my trusty Wahl clipper after it took an unfortunate spill to the floor after years of use. Using these directions, it was very straightforward getting the new blades into position and now the clippers work like new again. I don't understand the complaining comments here, as the two illustrations in the video show exactly what is needed more clearly than a video image could. A tip: after getting the blades into the position indicated in the two illustrations, rotate the clipper and "sight" down the length of the blades from each side. This will give you a clearer view of the relative positions of the two blades, and especially whether the gap is even from side to side. Tighten, sight, tighten, sight until the screws bottom out and are snug. Cheers!
@Wahlpro
10 ай бұрын
We're glad this was helpful for you!
@MotherScreng
6 ай бұрын
thanks! i replaced my blade after years, what a huge difference. But i of course took it apart a few months later to clean it… and needed this to put it back together - thanks!
@Wahlpro
6 ай бұрын
We're glad this was so helpful!
@mistymockingbird3511
4 жыл бұрын
This is a terrible tutorial. Need a close up to make sure the bottom blade is in the correct orientation. Plus the alignment segment was confusing AF.
@tiffanyleonard9666
14 күн бұрын
How do you put the spring back into model 9336 clippers
@bellalugosi293
Жыл бұрын
Gee, the music really helps in comprehending these instructions.
@elainewinkel7883
4 жыл бұрын
After I removed the old blades and cleaned the actual clipper I thought replacing with the new blades would be easy. Nope. The instructions and this video both neglect to mention the 2 little springs or the "holder" the small blade goes in. Anybody?
@timmywashere1164
4 жыл бұрын
If you find out anything on this please let me know. I made the mistake of slightly moving mine and the spring popped out.
@mistymockingbird3511
4 жыл бұрын
Yeah, my blades are off by mere millimeters and this didn’t help at all.
@gapeachnow26
4 жыл бұрын
What clipper do you have? I'm not familiar with Wahl home cutting kits, but the professional clippers have a white arm the small cutting blades fit on. Is that what you're referring to?
@jkk4657
2 жыл бұрын
@@timmywashere1164 the two springs go behind the plastic keeper for the smaller blade. First two arms, then keeper then small blade. While holding this assembly done slide the larger blade over and tighten the two screws
@timmywashere1164
2 жыл бұрын
@@jkk4657 order isn't the problem. What's the orientation of the spring when you put it in?
@HighTemperature80
3 жыл бұрын
While cutting a friend's hair, I noticed the bottom blade of my Legend 5 stars has slid visibly from the original position. It only took a gentle nudge to slide it completely out of the machine. I unscrewed the first blade and now I am stuck, I have no idea how to proper get the bottom blade into place. Any chance there is a schematics or another tutorial available?
@jsmith23xify
4 жыл бұрын
Mine wasn't cutting, so I unscrewed the blade screws and tried to put it back. Now the right screw won't screw into the blade it looks like the screw is too small, so I ordered a replacement still no go. Any advice or do I need another clipper?
@HyperChym
Жыл бұрын
This mounting method can be used for dual blades of magic clip cordless
@tequilaburp
3 жыл бұрын
This manual alignment is dangerous. If you put it in the wrong position you will end up with a cut on your face. Test the alignment with toilet paper before use it with your skin. Push the clipper towards the toilet paper to make sure blade wont cut you. WAHL should design clippers to self-align when placing both blades.
@dannybalanta1987
5 жыл бұрын
Can i use a 1006 blade for a 1045 blade designed trimmer?
@Wahlpro
5 жыл бұрын
The 1006 blade will fit on a 1045 designed clipper.
@mypiggypearls
5 жыл бұрын
well MINE does not have screws to remove.. it has something looks like an allen wrench but is NOT working...i can get them on if i could get the blasted ones off that came with it
@Wahlpro
5 жыл бұрын
Where are you located? Do you know which clippers you are currently using?
@whalesong999
4 жыл бұрын
Is the quality of the pet clipper blades any different than other two hole blade sets? I just ordered two blade sets for my PCMC model and I'm not sure they will perform as well as the original set that came with the unit.
@Wahlpro
4 жыл бұрын
Quality of the blade should be the same however the cutting performance (length specifically) may be different.
@whalesong999
4 жыл бұрын
@@Wahlpro Thanks.
@MrREALM1000
4 жыл бұрын
Helllo i have a question i bought a Performer by wahl home cutting kit and one of the large blades teeth was broken can i still use it will there be any problem do i have to buy a spare immediately or is it still good for cutting thank you
@gapeachnow26
4 жыл бұрын
If a tooth on the large blade is broken, it means the small moving blade's teeth are exposed and can cut you or your client. Replace the blade set.
@EmersonDubronxs22
7 жыл бұрын
wahl como podemos negociar um patrocínios sobre maquinas de corte acabamento eu faço propaganda para vcs então como entro em contato cm vcs para cvs
@Дбпжф
4 жыл бұрын
Sir hi i have exactly the same but it's broken the plastic inside who moves the blade what is called and. Where can i buy it thank you if you could help me
@Wahlpro
4 жыл бұрын
Where are you located?
@Дбпжф
4 жыл бұрын
@@Wahlpro Greece eu
@Wahlpro
4 жыл бұрын
@@Дбпжф Please contact our Wahl Europe team and they can assist you. wgalpha.northcentralus.cloudapp.azure.com/wgapp/ContactUs.aspx?lang=wg-EU&SiteId=17&SinId=Array
@MarkelleFultzCuzin
3 жыл бұрын
Hey i had this problem when i was detaching my clippers and these two pointy things appeared, I cant put everything back. What is it?
@Wahlpro
3 жыл бұрын
It sounds like it may be the tension spring. Please give our technical support staff a call at 1-800-767-9245 and we can assist you with this.
@killerjo-209
7 жыл бұрын
what's the name of that song?
@cactus-nk1hx
4 жыл бұрын
hi .i have wahl rfjz-2205 .. An old one wahl belongs to my father..may i know..can i replace it with any of 2 hole blades? as It is an old model, its hard for me to find a sparepart..
@noeljohnson868
5 жыл бұрын
That diagram at around 40 seconds is no help at all - it's easy if you do this sort of thing all the time, but it's just a line drawing which could - to the uninitiated - be of either side of the blades which means it would all be set up wrong. A better idea would have been to show the actual clipper in close-up, and which way around it was, and then it would have made a whole lot more sense...
@agm1990
3 жыл бұрын
Where can I get the sponge that is inside the clippers?
@Wahlpro
3 жыл бұрын
Give our customer service a call at 1-800-767-9245 and we can take care of this for you
@HyperChym
Жыл бұрын
which means we will push the blade all the way to the right so that the first tooth of the blade coincides as shown
@airyair9889
5 жыл бұрын
That diagram is complicated as heck....just want to shave my dog. For me, would you please describe the alignment part in a simpler way?
@noeljohnson868
5 жыл бұрын
OMG, so agree...
@BlakeSuperior_Beats
6 жыл бұрын
Why do they want the cutting blade off to the right instead of in the center of the still blade?
@gapeachnow26
4 жыл бұрын
Because the small cutting blade moves to the left when it's on. If it were in the center, the left side of the cutting blade would come off the stationary blade and cut the skin. I know this comment is old, just answering in case anybody comes by wondering the same.
@BlakeSuperior_Beats
4 жыл бұрын
@@gapeachnow26 The cutting blade moves both left and right. When I zero gap, I always push the cutting blade as far right and left as possible to make sure the still blade is perfectly centered.
@e-rico7903
3 жыл бұрын
Danielle been looking for this question, got almost the same one. I had this cordless magic clipper, when i turn on, turn it off, the cutting blade stays to the right. Turn it back on, turn it off, blade stays to the left. Was that normal or the cutting blade should always stays to the right everytime you turn off the clipper. Also, when the clipper is turned off, would you be able to move the cutting blade by pushing it? When i pushed it left to right, it moves, but gets still after pushing twice, was that normal? I thought the cutting should stay where you placed it when you tightened the screw. Thanks
@theravedaddy
2 жыл бұрын
This makes no sense at all. My wahl clipper has shoulders on the screws. The shoulders are the same size as the large blade holes so theres ZERO adjustment. I cant find an answer to this anywhere.
@DuzBee
4 жыл бұрын
I agree, that black and white ‘photo copied 100 times 1950’ image is piss. Put some effort in Wahl... demonstrate blade alignment with the actual clippers.
@michaelgainey5051
3 жыл бұрын
Cause it didn't fucking show me how to put the black u shap pin in the white plastic piece
@alexadler6253
4 жыл бұрын
I still all this and still doesn't cut my beard
@johnnyvegas5681
3 жыл бұрын
Wow..,this is actually from Wahl? They should be embarrassed!
@Wahlpro
3 жыл бұрын
How so?
@sabra4624
3 жыл бұрын
Awful and on website would be better if you could enter model number somewhere as my clippers are several years old and I can't locate the instructions or manual. Website opens petcare when I try to search.
@Wahlpro
3 жыл бұрын
The professional website for Wahl is wahlpro.com. You should be able to search for your item either by part number or name here.
@BBpoopin
11 ай бұрын
This is a poor representation of whats required to get this repair done. In the comments OP is referencing springs or pins but nothing is shown in the video. All this video has accomplished is ensuring ill go with Andis clippers next time
@jeanberkogleason9596
3 жыл бұрын
Hideous music. Unwatchable
@KylieJonkman
Жыл бұрын
Really really unhelpful
@Wahlpro
Жыл бұрын
Oh no! What issues are you having that we can better try and assist you?
@cam4722
2 жыл бұрын
What a horrible design. As if a regular person is going to be able to line this up correctly. Do better, Wahl.
Пікірлер: 60