I have the same fan unit. I took the rectangle flange off of my blower and transitioned my discharge to the equivalent sq inches of the flange outlet. That portion of the flange with the round outlet was a less than 5" in diameter which represented about a 40% reduction on the discharge surface of the rectangle end area in sq inches. I also bought a larger impeller but even if I hadn't fiddled with the impeller, I'd still recommend losing that rectangle-to-tube flange. It's an absolute beast now! Restriction in the collection tubes is important but so is the static head pressure applied to the discharge of the fan. They only made it that way for cost purposes. Also, when you do this sort of thing, you get those actual flow numbers they advertise, which are taken from the fan unit before they "package" their "system". That's why you expect say, 1,000 cfm but only measure 400 or 500 in real world applications. And as you say, it only gets worse as the filter/bag/whatever gets clogged.
@davebishop2566
6 ай бұрын
Where I work we have multiple dust collection systems. As you said the filters systems are outside. They cost millions. I believe the problem is that they remove huge amounts of BTUs from the building. One of the systems removes Welding smoke and grinding stuff. Each system has to return the BTUs into the building. When a system isn’t working properly it’s a nightmare in the 100,000 square foot facility. Great points and take on stuff. I’m working on my home welding, machine and wood working shop. Can never stop improvements.
@andrewsmith3121
2 ай бұрын
Every 90 degree joint should be replaced with either 45 degree or 22.5 degree joints. Your extraction power and capabilities will improve to be 40-60% more efficient. With your "ceiling" height, the vertical runs are being suffocated with 90 degree bends.
@rickchichester9327
Жыл бұрын
I was able to use a heat gun to soften my pipe and fittings to press fit on some of the tools
@dennistaylor7655
2 жыл бұрын
Thanks for posting this. It validates my thoughts about moving everything outside and doing away with expensive filters.
@MatthewPeechWoodworking
2 жыл бұрын
Glad it was helpful!
@tclynn10
Жыл бұрын
This is without a doubt is one of the most informative dust collection videos I've seen yet. Bought a Harvey dust collector last week and just ordered the ductwork tonight, can't wait to get this machine going! Thank you!
@brendaedwards7396
Жыл бұрын
Good tips, my previous shop I had run the dust collection port through the wall as you did. However, did not realize that the negative pressure created inside the shop would suck the smoke down the chimney of my wood stove. Had to open a window while in use. I was evacuating the heat out of the shop.
@randallnorris231
3 ай бұрын
SON! You have an Awesome shop.. Bigger than a lot of homes..lol. Thanks for the info on the adapters.
@MatthewPeechWoodworking
3 ай бұрын
Any time!
@terrydoublin1398
Жыл бұрын
I just did this very thing, but my collector is mounted up on the wall inside my shop and blows outside but thinking about building a room outside for it to go in to make it quite. The price of the 6 inch pipe and fittings is tough to swallow but well worth it.
@bobbywhite8331
2 жыл бұрын
I think you could increase CFM by converting your exhaust to 6 inch pipe . The rectangular port has basically the same cube as a 6 inch pipe but manufactures will instantly drop it to 5 inch .. opening that up to 6 would probably add 150-200 CFM . You can’t pull in more than you are letting out
@MatthewPeechWoodworking
2 жыл бұрын
Very good point and I attempted to convert it 6. If I start having issues I'll def do that but I've had no issues so far.
@everettcaudlesr.7671
2 жыл бұрын
I converted my old in shop system similarly. Mounted the old motor and impeller unit to a support post near the ceiling, put in a trash can separator to catch the bigger stuff between my upfeed ducts and the impeller, and ran the exhaust outside through the wall. I use a remote control to switch the motor on and off. Several benefits: better dust and chip removal from the machines, less floor space needed for dust collection equipment, and (most impressively) a significant reduction in dust collector noise in the shop. I may end up eliminating the trash can separator since I live in the country and sawdust being exhausted into the outdoors is not an issue.
@paulgriffith3549
2 жыл бұрын
I have worked in two wood shops just like yours, one I owned and built my own dust system. I also worked in a cabinet factory. Every Dust collection line had to have a ground run with it. I wonder if you have any static issues? Also the one shop I worked in, the owner ran low-voltage contacts to the gates and when you opened a gate the system would come on.
@markmurrell1894
11 ай бұрын
You just blew my mind. I’ve been watching videos after videos on dc and trying to learn about the filters or bags to keep the air as clean as possible. I never thought about just mounting the motor outside my shop and just collecting dust inside a trash can. Keep it outside! I have a lean to on my shop and believe I can tuck it up in the ceiling of the lean to and it shouldn’t get wet or anything. Thanks for the tip!
@CaptainKseadog1
2 жыл бұрын
I like the idea of venting your vac system outside if availabe. The only down fall i see is that if you are heating your shop during the Winter, you will be sucking all the heat out side.
@tommyb1884
2 жыл бұрын
Thanks for this. Huge help with what I’m trying to do. Love your videos and appreciate this channel.
@ernieforrest7218
11 ай бұрын
Good video, very nice installation. As you said, the planers and shapers are the machines creating the most dust. A large planer of 20” or more with a large motor will tax the system the most. Especially when say a large draft of lumber is planned at a session. In larger shops its sometimes better to have things like hand sanding stations and edgebanders on a separate individual system. They dont make all that much dust anyway. My son has a large shop, and he uses PCC pipe also. His system is a large cyclone installed in an outdoor shed against a side of the building. It simply empties into a standard trash can, but is pumped from that to a fully enclosed dump trailer. When the system is running the pump is running also. It dosent take all that long to fill the trailer when planning a large quantity of lumber.
@TexChopper
3 жыл бұрын
Hey Matthew. Love the shop, and love your videos. I'd like to voice a small concern I have with your roof structure. I'm a truss guy, and I've been designing trusses for over 20 years. My concern is the lack of bracing I see in your trusses. You should have sealed engineering sheets that specify what bracing is needed, and it may require none, but it almost never does. If they don't require any, then my apologies. However, if this is not the case, then I would recommend you add bracing.It looks like you have 2x6 top and bottom chords, and 2x4 webs, and a span of about 30'. I'd brace the bottom chords with purlins AT LEAST every 10 feet if not closer. So you'll need at least 2 runners going the length of the building. I'd also recommend a bracing purlin in the middle of each diagonal web, and also the length of the building. The top chords should be fine, since they're sheathed. I know you didn't ask for this "advice", and I don't mean to be "that guy", but I've been working with trusses a long time, and I like you, so I want your workspace to be safe. Trusses are awesome, but they need bracing to work properly. Sorry if I'm overstepping, just want to help out a fellow woodworker. Take care, and God bless you. Thanks for all the great content.
@MatthewPeechWoodworking
3 жыл бұрын
No that’s the king of feedback I want. Thanks so much for the advice. I was thinking I needed bracing anyway and you just confirmed it. I’ll add that to my list! Again thank you! Any feedback Is welcomed!
@gordonmoen6038
5 ай бұрын
Concerned about her loss in cold Michigan winters and humidity gain in muggy summers
@jameshogan2250
5 ай бұрын
Unfortunately, in my little shop, It would pull the heat out quicker than I could produce it. So I have to use the cyclone and good filters. Love your videos.
@Hunterworks
6 ай бұрын
Huge question I do not think you answered, where does the air come into your shop and how do you handle heating and cooling with that much air exchanging?
@12982blackjack
2 жыл бұрын
Wow, I love your shop. I'm getting ready to install the metal blast gates and no doubt I would've installed them wrong. Thanks!
@MatthewPeechWoodworking
2 жыл бұрын
Thanks and no worries!
@jujubean569
2 ай бұрын
Mr. Matthew, I heard a mention of static in your tutorial, but I didn't hear your reference to a grounding in your PVC system, Sir.
@cyrilnorrie8450
6 ай бұрын
An excellent system in a great shop! I appreciate your advice and tips on building a DC system. I do have a concern that it might take a lot of heat out of my shop in the winter, but in the warmer months that would’nt be a problem.(l live in Alberta, Canada.)😊
@katew3808
3 жыл бұрын
Great video ! Your shop is my dream space !
@MatthewPeechWoodworking
3 жыл бұрын
Thanks!
@jamietrasciatti5871
2 жыл бұрын
Love your channell!! Looking forward to getting my shop up and running in the next month or so. You always provide great content! Thank you!
@btigenie
7 ай бұрын
I know this video is old but it is still a great reference! At timestamp 4:30 you are holding the divider piece from the dust collector. Yours is 6 inch by 2 @ 4 inch. The divider piece from my dust collector (2 hp harbor freight) is only 5 inch by 2 @ 4 inch. Would you suggest making a different divider plate that is a 6 inch piece and run 6 inch everywhere or just downsize it to 4 inch and use the 4 inch for the backbone of the entire system? My shop is 24x24 and I have no 220v tools. All tools (circular saw, planer, chop saw, etc. - no jointer yet) are hobby grade type machines (ridgid, dewalt, etc.) I am starting to plan for the layout of the shop and would love your feedback.
@gallop8499
Жыл бұрын
Great dust collection video! I have a very small shop and have been wondering about mounting dust collection on an exterior wall connected to my goat shed for using the shavings. My only question, without a filter, do you have any issues with lost screws hitting the impeller?
@wate98
2 жыл бұрын
Hi Matt! I'm curious- without some way of replacing the air being sucked out, the building will immediately go into a vacuum and significantly reduce your CFM being sent outside. What was your solution that replaces the exhausted air with "fresh" air?
@rodpotts2666
3 жыл бұрын
The main reason I have seen is it sucks the climate controlled air and blowed it outside. I never thought it would make that much difference,unless the dust collector is running most of the time while in the shop. Shop is looking great. Coming right along.
@MatthewPeechWoodworking
3 жыл бұрын
Yea most articles I’ve read no one can tell a difference in climate at all. Maybe unless your setting up to cut parts for hours we kick them on and off. And with only one blast gate open I’ve noticed zero difference.
@RedcarWW
2 жыл бұрын
At the beginning, you mentioned how the Y that comes with the dust collector reduces your CFM by half. When you come through the wall, you go into a 90 degree T. 2 thoughts here. 1. Doesn't the T as you come through the wall reduce your CFM by half like the Y would? 2. Wouldn't you be better replacing the T with the Y and using another 45 degree angle elbow? This would remove your 90 degree turn? Don't mean to be that guy questioning your configuration. I am in the process of designing my layout, and understanding simple concepts like the T over the Y will help me understand the mechanics. Thank you for your content.
@mindbodywellness2150
3 ай бұрын
I was wondering the same thing
@Ron-FabandBuild
6 ай бұрын
Excellent information Matthew. Thanks again
@MattSBailey85
2 жыл бұрын
This is really smart. You don't even have to have the whole blower outside, you could potentially just run the exhaust outside into a trash can or something (I don't live in the country)
@timjohnson1578
Жыл бұрын
you're ideas and examples are awesome for us new guys. Thanks so much for the information.
@scottensor650
2 жыл бұрын
Love the shop. I also live in the country and want to put together a dust collection system like yours. I noticed and I think you said, that the blower was a Grizzly. I went to their site and cannot find just the blower for sale. Can you point me in the right direction.
@chadgillaspie7203
2 жыл бұрын
I've been watching you a while now, never knew where you were from and I work with a guy that said he went to school with you lol. You're right down the road from me lol.
@MatthewPeechWoodworking
2 жыл бұрын
Lol. Small work Chad!
@niccolealdrich4890
Жыл бұрын
VERY informative! Thanks for sharing! Just out of curiosity, what size is your shop? Also, do you have a link for your dust collector unit?
@arkansasboy45
Ай бұрын
What about grounding? Any problems with static electricity?
@buggyridge
Жыл бұрын
Outstanding Matthew! Thank you. Just what I needed to know.
@MatthewPeechWoodworking
Жыл бұрын
Great to hear!
@ehrhart4119
4 ай бұрын
I've set up a woodworking shop and now have a clean slate, but I'm uncertain about what diameter pipe to opt for in my dust collection system. Currently, I'm equipped with a Harbor Freight 2HP setup, enhanced with upgraded fan blades and a P181038 filter, alongside the addition of the Oneida Cyclone, which I've wall-mounted. I've noticed many KZitem creators employing 4" pipes, while a few opt for 6". Could you shed some light on why you chose the size you did?"
@jamesward1855
7 ай бұрын
Question, can you run your power cord with your dust collection pipe?
@woodworksbygrampies1284
Жыл бұрын
Hola! 🖐Thanks for going over this in detail. I found it very informative and educational. Will you be doing a "review" now that you have had this in place for a while? Have you made any changes or revisions? Also, did you get your miter saw situation figured out? I've seen Travis @shopnation working on putting together some interesting options. Take care and have a good one, Adios! 👊
@robbongiorno2651
2 жыл бұрын
Hi Matt, Thanks for all the insights and advice, all very well done and easy to follow. My question is, do you have any issues with static using PVC? either dust getting stuck to the sides, or even potential fire hazard from sparks? Thank you in advance.
@MatthewPeechWoodworking
2 жыл бұрын
Hey Rob! Zero static... no dust issues. From the research Ive done theres never been a documented fire from a collector from static.
@4149dwiley
Жыл бұрын
Hey wondering if yu have any issues with larger wood pieces damaging your fan impeller? Thinking of doing same thing but wondering to place a cyclone drop out before blower. Considering this and the amount of CFM loss from it. Any insight is helpful with why you did not have one and you passed all particles through your blower. Thank you and have watched most videos. I live across the river from you in Corydon.
@ScottJacobsenTurtle
Жыл бұрын
I am wondering the same thing. I hope Matthew answers you back, now that he has had this system running for a while.
@4149dwiley
Жыл бұрын
Another question is, Does the large chunks damage fan impeller?
@ScottJacobsenTurtle
Жыл бұрын
Have you considered using a HEPA shop vac on your miter saw dust port, and then a hood hooked up to your dust collection system?
@nctplarry
2 жыл бұрын
Thanks for this no-nonsense explanation, complete with suggestions from your School of Hard Knocks! A relatively new subscriber here. --Dr. Larry S. Anderson • Tupelo, MS (birthplace of Elvis)
@jimholman7682
2 ай бұрын
What dust collector model you are running? I see it is a grizzly, but what model? How many CFM does it have?
@randymartin2396
2 жыл бұрын
THANK YOUI VERY AWESOME CONTENT GETTING READY TO BUILD A SMALL SHOP
@copperhead94
7 ай бұрын
Great video Matthew. I’ve been trying to find the same Grizzly 2 hp dust collector you have and can’t seem to find one. Do you have more specifics about the model or a link to where I can purchase this one? Thank you
@mrmajestic345
2 жыл бұрын
The main disadvantage to this is, if you live in a cold climate, during warm season would be great, but not during cold season.
@MatthewPeechWoodworking
2 жыл бұрын
I worked all winter long here many days well below freezing with no issues.
@mrmajestic345
2 жыл бұрын
@@MatthewPeechWoodworking must be a mild winter, compared to where i live, would suck to much cold air into shop, where i live
@skiroy56
5 ай бұрын
What is the decibel level at the outlet on the outside?
@bryanhudson8087
Жыл бұрын
Thanks for the grand tour of your sawdust collection system, I am curious if you installed a spark detection system?
@bonefisherman71
Жыл бұрын
Mathew, Dust collecting has been my biggest challange. I just moved and am building about a 600sf shop. I learned a lot from this video but I couldn't find where you got your 2 hp motor. It says Grizzly on it but I could find it in the grizzly catalog. Could you share where you got it. Thanks
@tomyaniszewski9122
Жыл бұрын
How did you handle the static electricity?
@billibsen2329
2 жыл бұрын
1. You mention online calculator tool to calculate CFM and static drag - can you provide a link? 2. How did you transition from the rectangular top of your Grizzly dust collector to the 4" PVC pipe to expel the sawdust into your cart? Loved your videos on this subject - and you saved me a lot of money not buying a $4K dust collection unit!
@Caleb-vr1mi
2 жыл бұрын
I always see when people use pvc they have some kind of static issue with dust all over the outside of the pipes. Obviously you dont have an issue with that and you have a very clean setup. Any idea why though?
@diybuildandlife207
11 ай бұрын
I dont want to break open the siding to vent outside. Can i just crank open a window and let the hose go out when i use the dust collector?
@mjcaulkins
Жыл бұрын
So what are your thoughts on grounding lines when using PVC. I was looking into this years ago and everything I read said these were important. I guess the concern is static discharge possibly igniting the fine dust, although that might not be as big of a deal since your discharge to the outside.
@kevinrhug
Жыл бұрын
There has been new research that demonstrates that static discharge will not ignite the dust but i did get a static shock from my planer. In my new location i am switching to galvanized vent pipe
@mikejackson2888
3 жыл бұрын
Great video, now it all makes sense. Good points and tips. One question, are you worried about static build up? Lots of opinions on it with PVC pipe
@MatthewPeechWoodworking
3 жыл бұрын
I’m personally not. But to each their own. Studies have shown that static has never caused a known fire. I’ve worked in a mill where we ran 8 hours a day without grounded pvc. 6-8” lines and 6 cutter heads going at once.
@BPR-76
11 ай бұрын
Great video!!! Where is the dust going? Into a bag? 55 gallon drum? When you say “outside”. Do you mean into the open air?
@kevinrhug
Жыл бұрын
I am setting up my new shop and I have a woodtek 4 bagger. I would like to exhaust my dust like your system does but I am concerned I will lose all my conditioned air in no time. What climate is your shop in?
@jbergenudd
Жыл бұрын
can you get a Y with 6 inch but the pipe going off it as a 4 inch? then you can run 6 longer...
@ET-yr6st
7 күн бұрын
what model # is the grizzly dust collector?
@brentjohnson6654
11 ай бұрын
New subscriber here. Thanks for the video. I am a retired engineer in Texas looking to add dust collection. Did you have to the impeller just blow that outside or did I miss the collection part? We live in the country and I wonder when it would be a problem not to collect that fine dust (.3 - 10 micron). Thanks again for the videos and how you explain it. All the best from north Texas.
@bryanhemphill6596
6 ай бұрын
I have searched grizzly ect for that blower/ suction/ collector.and can't find that unit anywhere .looked below vid and found no mention of it can anyone help??.
@jeffreyjohnson2444
Жыл бұрын
Where did u get the motor from
@stevewanke2546
2 жыл бұрын
You didn't explain how you made the transition from the Grizzly collector to the 6" trunk line? Does the 6" sewer pipe fit snugly on the grizzly collector port?
@MatthewPeechWoodworking
2 жыл бұрын
Actually it doesnt. I had to build up the collector port OD with adhesive foam strip to the point it made a tight seal when I slid the pipe over it. Then sealed with duct tape.
@stevewanke2546
2 жыл бұрын
@@MatthewPeechWoodworking thanks for replying. Plumbing in general is pretty madening when it comes to sizing and unfortunately this carries over to dust collectors as well. Great video though
@robertspina4503
2 жыл бұрын
Another great video
@MatthewPeechWoodworking
2 жыл бұрын
Thanks!
@teroyjenkins30
2 жыл бұрын
My question, and maybe I missed it. Where is your motor and fan in relation to the collection trailer? It looks to me like it’s in the middle.
@davesatosky5840
2 жыл бұрын
how the hell do you run that dewalt planer without any ear plugs or muffs lol
@MatthewPeechWoodworking
2 жыл бұрын
what... speak up please...
@alanmatthews9260
11 ай бұрын
Are you saying that there’s a giant pile of sawdust and wood chips in your backyard?
@macminn18
8 ай бұрын
Brilliant, love this. We recently moved out and I have the space to do this! One question, do you have problems with critters getting in the sawdust? Or having it get moldy?
@allenthornell2763
2 жыл бұрын
I'd like to get your opinion. I have a fairly small basement that I do my wood working in. The big tools I have is Table saw, planer, miter saw. I've started researching dust collection. I make what I can with my little time in the day I have left. Harbor freight has a 1 hp dust collector for 75 dollars more of what a decent shop vac is. So do you think I should take the shop vac/ separator route or the dust collection system route. Thanks
@mikeliles3221
Ай бұрын
why did you go from a 6" down to a 4" line?
@billibsen2329
2 жыл бұрын
How did you transition from the rectangular top of your Grizzly dust collector to the 4" PVC pipe to expel the sawdust into your cart?
@RusticNail-fw9rf
Жыл бұрын
Have you had any issues with static electricity? I am in the process of installing one like yours and am worried about static and am thinking about adding a grounding rod. Would love to hear back from you.
@AlanCamby
Жыл бұрын
hey bud your channel is really great and informative big thumbs up have you ever thought about a rousseau 5000 dust hood for the miter saw check it out .shops looking super nice so far
@douglingle1600
3 жыл бұрын
Hey Matthew....great looking shop and dust collectiion set up, what did you run your outside pipe into, thanks.
@MatthewPeechWoodworking
3 жыл бұрын
Hey! I just posted a video that shows my setup. But really anything will work so that air can escape. You may have to play around with it a bit.
@MatthewPeechWoodworking
3 жыл бұрын
Mines a trailer btw.
@douglingle1600
3 жыл бұрын
I have a small shop and i do live out in the country, so i believe this will work for me as well.
@weigandworks6151
2 жыл бұрын
Shop looks fantastic and such a great setup for a 2hp collector. What does the outfeed feed into when it goes outside? Looks like a trailer of some sort? What do you do with the dust/shavings? I plan to do the same thing (having the outfeed just go outside), but I will also have a garden outside, so I don't want dust from MDF, etc. type materials freely flowing around and getting into the garden.
@MatthewPeechWoodworking
2 жыл бұрын
I have a small trailer that we then use the shavings for animal bedding. Or you can simply burn, dump or bag it.
@weigandworks6151
2 жыл бұрын
@@MatthewPeechWoodworking love it!! Thanks got getting back to me. Going to model my dust collection after your setup
@grantskelton1219
2 жыл бұрын
How do you get such a small system to get enough suction over such a long run?
@davidpauline5439
Жыл бұрын
Matthew I love your videos and your perspective. I was just watching your series on dust collection and would like to know what model is your Grizzly dust collector. I am setting up my shop going to be approximately 32 x 20. I really like the system you have set up and plan to use it as much as possible. I appreciate any info you can provide. God Bless and Merry Christmas David
@fdort3971
Жыл бұрын
@MatthewPeech that's a very impressive system but I'm a bit out of my league...lol...since gravity exists I was thinking of running my lines along the ground...would that work? Like make a covered trough...you said a collection would reduce suction...I want to collect so I can make fire logs to sell or loose for critters. How would I combat this please? You used pvc...can I also use stove pipes or heat ducts? I'm kinda sensitive to static electricity...how do I ground it? Trying to plan ahead for my first woodworking shop.
@fdort3971
Жыл бұрын
Also...what the heck is an impellor? I saw it mentioned in other comments
@katew3808
3 жыл бұрын
What's static drag and how did you handle that ?
@MatthewPeechWoodworking
3 жыл бұрын
As of now I’m not worried about the small amount of static drag. Some people ground their lines. I may in the future but I don’t think it’s needed. But to answer your question in theory moving particles across surfaces causes static. Like dragging socked feet across carpet.
@herbiebohrer8306
2 жыл бұрын
If you don't mind me asking...How much $ do you have in your entire dust collection system? If you don't want to answer that I completely understand.
@eb4326
2 жыл бұрын
Great video. I plan to do the same as you did and even found the same unit to use. I noticed that you had the dust collector really close to where you have it exit the building. Is this necessary? I was thinking of putting my collector in the middle, but wonder if running the exit pipe 20 feet to the wall will be too long? Thanks for the video and any help.
@MatthewPeechWoodworking
2 жыл бұрын
I dont think you will have any issue with placing it in the middle. Mine just happen to end up close to an exterior wall.
@eb4326
2 жыл бұрын
@@MatthewPeechWoodworking thank you!
@deniseclark9150
Жыл бұрын
What is the square footage of your shop?
@lancebenton6801
2 жыл бұрын
Instead of blast gates... would a ball valve work?
@Powerstroke7911
2 жыл бұрын
I’m sure they would work as well, if not better, as the blast gates. But at that diameter, ball valves are PRICEY! For those few where price is not a factor, I think they’re a viable option. Just my 2 cents….
@Continuouscustoms
Жыл бұрын
What size is your shop?
@19570219
Жыл бұрын
KEEP IT SIMPLE SWEETY VERY GOOD MAYBE JUST USE A PLASTIC 45 GAL DRUM WITH A LITTLE WATER IN IT? BEST I HAVE SEEN....
@tomd.7325
Жыл бұрын
Don't you LOSE a lot of heat or cool air in your shop ? that air has to be replaced by something!
@rootedwoodcraftssamuelwarf45
2 жыл бұрын
Something tells me this guy doesn’t live in a cold climate… It exhausts all your heated air outside and sucks in cold air…
@villijs33321
7 ай бұрын
This is not really whole shop - it's a sible tool in shop ran on old collector. Whole shop would mean that all blast gates are open and still get good collection on all of them - this is not the case...
@LegoPictures2
7 ай бұрын
Too many sharp turns
@thomasboyd6242
Жыл бұрын
I’m just starting to build my dust collection system. Why did you choose the metal blast gates as opposed to plastic ones?
Пікірлер: 125