Ty! I thought I was going crazy or my hearing was fudged or something! Lol
@Edub816
Жыл бұрын
@@matthammond6948 same. Thought my AirPods were broken.
@charlesreeves3426
Жыл бұрын
After 30 years of shooting recreationally and professionally, I have found these gas blocks to be superior in every way to other so called top tier manufactures. The ocd in me appreciates the focus on the design, fit and function of not only this product, but also their LDR 1.5's and 1's. Ill keep my fingers crossed, hoping yall come out with a 0.750 gas block.
@MR-vk9li
Жыл бұрын
Having mounted this to a CORE barrel, I can say the fitment is perfect. This is a low profile but heavy duty gas block.
@MrLahey69
6 ай бұрын
The $15 expo arms gasblock is 4140. L0L
@LONEWOLF_LCD
Жыл бұрын
I heated up the Gas Hole to slide it on….. I will say if you stop before it’s perfect it’s a pain in the ass to to adjust….. and with that Gas Hole being so tight, there is no need to pin…. It will be a act of god for the Gas Hole to move once installed
@grantsdad177
Жыл бұрын
You sold me lol added on the badger tdx when I bought my barrel and have been considering the ripcord gas hole for months my backorder should be fulfilled soon so I figured it’s time to bite the bullet considering this is a no expense spared build
@evanacey1414
Жыл бұрын
Sick shirt man
@baseline_training1098
Жыл бұрын
This gas block is no joke. It's not going to be easy to install, BUT it has the best lock up over any other gas block I've ever installed. Going to test my 13.9 on a machine gun lower sometime soon and put it to the test!
@TROY-MCCLURE-1991
Жыл бұрын
Update?
@gregsicinski8138
11 ай бұрын
You actually received your gas block?
@jimjones516
Жыл бұрын
just ordered mine for my criterion core 13.9"
@fook-joby-den6172
Жыл бұрын
I had a Similar Quandary I was Comparing the Following: -14.5 CHF Hodge(Chop’d to 13.9”) -16” DD Middy S2W CHF Chrome Lined.(Chop’d down to 13.9”) -14.5” RainierArms Mountain Mod2: (4150-..QPQ Coated/SDM Flute’d from the Barrel extension up to the Shoulder of the Gas Block). -WOA: (WhiteOakArmament)l223 Wylde 16” SDM Fluted Middy 416RR(Raw-SS),Chop’d Down To 13.9”. Mod3 Grip, just InCase I Ever need a Spare. Due to wanting up “Accurize”” the upper as much as I could. So, went Criterion 13.9” Core Criterion Lined .223 Wylde+ Riptide Industries Gass-Hole Fixed Non-Adjustable/Gas Block+VSeven Weapons Systems Extreme Duty Inconell Gas Tube, Capable Citizen Variant SOLGW BCG(w/HeadSpaced Bolt That Came w/Criterion Barrel+SOLGW Stripped Upper that’s Lapp’d & has had Feed ramps of barrel extension polished after installed. Barrel Bed’d in upper AFTER Face of upper has been lapped. Using a NOX-9Port W/Keym along with a DA Sierra 5 Suppressor, & a M76 WedgeLock 13” Rail/Hand Guard torqued to many unhappy-dungas(say 70-85FTLBS to ensure Great Lock up. Then last but not lease I’ll carefully Secure Any Mloc Attachment Points have been trimmed w/ my dremel(bc DrEmEl= GuN sMifF😂)to the Rail so that none of the Male Ding-Guss’es Hit the barrel so there no issues negatively impacting the barrels harmonics. As for Glass: I’ll be rocking a Badger Condition One 30mm 1.93” Mount+35Deg Offset(1.93” height)J-Arm+RMR baseplate+Holosun HE509T Elite MRDS+Primary Arms PLx-C(Gen2 PLx Compact LPVO) with Ye’Old (ACSS Raptor M8 B.D.C. Reticle)
@Teleman01
Жыл бұрын
When will they be back in stock??
@davidcunninghamjr6871
Жыл бұрын
From a mechanic/machinists point of view because the tolerances are so tight couldn’t you just freeze the barrel and then fit the gas block into it. This way there’s no need to remove any of the coatings and it provides an even tighter tolerance mating surface?
@peeeoii2738
9 ай бұрын
Usually no visable chage for barrel diameter on .0005 resolution calipers might be able to see a difference on some Mitutoyo mics that go out to .00005 but it’s too little at that point so heat up the gas block before installing is better.
@Aaron-ed2rb
6 ай бұрын
@@peeeoii2738I’ll just do both
@JC-eg8np
Жыл бұрын
will this gas block work on other barrels?
@rickypickles2219
Жыл бұрын
When will those dope handguards be back in stock?? I need a 13.5 rail
@ripcordindustries9871
Жыл бұрын
They will be available again starting in the middle of February.
@tf201
Жыл бұрын
Now I’m debating if I should use this instead of the V Seven Titanium .625 for my upcoming build with a criterion barrel. Aren’t criterion barrels already setup to be pinned?
@grantsdad177
Жыл бұрын
Nope
@ChaoticCarl86_YT
Жыл бұрын
They don't have a pin groove, but they have a single dimple for set screw style gas blocks. I have a barrel with a pinned, set screw style gas block and a criterion with a dimple, but used a clamp on block. I can't imagine one being more reliable than the other unless you just need the peace of mind. *I don't say this to sway your opinion from getting this gas block, I'm sure it'll perform on par, if not better than most out there because of the engineering behind it.
@modernrambo2
Жыл бұрын
Are these skinnier than a TDX manifold? I have one in .625 that is ever-so-slightly touching my 11.75 LDR1.
@Esydow13
Жыл бұрын
Our Gass hole is .064 smaller than the TDX manifold.
@denbo74
Жыл бұрын
10 weeks for this thing?
@Don_Frahn
Жыл бұрын
No .750??
@UmamiPapi
Жыл бұрын
Down mixing your audio to mono will fix the problem of only playing in one ear.
@johnsnow7575
3 ай бұрын
i need prices and inventory on 13.9 uppers nothing is on the site.
@brian.delphia_actual
7 ай бұрын
Trying to find the how to series
@evoasus2286
Жыл бұрын
Interesting on the pinning. I was going to have mine pinned, but you don't find it necessary, then I might elect to just not do it.
@romang6437
Жыл бұрын
The only thing I don't like that you have to take phosphate coating down on criterion barrel in order to fit this gas block.
@airdusterenjoyer
Жыл бұрын
Better to hone the inside diameter of the gas Block. Not sure what the instructions are for this specific block but that's usually the sop
@xifogetx
Жыл бұрын
Thermal expansion is your friend.
@pusmaster
Жыл бұрын
hmmm
@joshdennis8841
Жыл бұрын
When will these be available again??
@ripcordindustries9871
Жыл бұрын
Hey Josh, they will be back in stock between March 3rd and March 10th depending on how long coating takes.
@joshdennis8841
Жыл бұрын
@@ripcordindustries9871 just ordered one!! Can’t wait to get it and finish my build
@seanhatch4425
5 ай бұрын
Are you the guy from T- Rex arms?
@kevinclark6801
20 күн бұрын
Get these back in stock otherwise I’m going to have to use a Bcm gas block
@KentuckyReef
Жыл бұрын
What the hell happened…drop a video or two
@PrayingPanda
11 күн бұрын
10:44 had to stop watching here. This was so disingenuous. No one screws in the front gas block screw before screwing in the rear one. Come on dude.
Пікірлер: 45