17:50 I'm imagining the two darts being very polite and going "after you" "no I really must insist, after you" Really enjoyed this review format, a very warts and all approach. To make a bit of a gone in 60 seconds reference, The Dominator is shaping up to be the Eleanor of blasters
@yorozuya2898
5 жыл бұрын
I love the music and the camera setup. The music suits the type of video well with your overall format.
@TheSybermedic
5 жыл бұрын
Excellent video, a great follow-up to part one. Your methodical approach to the build is awesome. It reminds me of a very high quality how to video. I can't wait to see how you end up finishing this blaster. Overall I think your mods are the cleanest and and most visually appealing that I have seen on the web.
@homelee665
5 жыл бұрын
Great review! I especially enjoyed the part about curvy magazines and wheels with groovies.
@Slyd_Fox
5 жыл бұрын
Possible mag pouches that might work: HSGI "Taco" pouches. www.evike.com/products/47142/ and www.evike.com/products/48261/ Kinda pricey, but high quality. Quite popular in the airsoft community.
@vintajecheese7803
5 жыл бұрын
After watching the feeding issue in a very easy because your videos are very well shot and are zoomed in on all the details. I noticed that when you emptied the mag and kept firing the follower would move showing that the pusher is hitting said follower. My idea is to shave the bottom of the pusher until the two no longer contact or contact very minimally. But that's a lot of work to for a drop in kit. I'm really disappointed by Worker in this case and don't think this blaster isn't going to be as popular as there previous ones.
@Slyd_Fox
5 жыл бұрын
It seems that the double-stack mag would benefit from a re-design to a double-to-single stack configuration.
@StuckOnAFireHydrant
5 жыл бұрын
Just rewatching the video and I got to 22:50ish where you were talking about the darts getting stuck at the same level. I was wondering what would happen if the Pusher was asymmetrical to push just one of those darts into the flywheels?
@EDSKaR
5 жыл бұрын
1 did you test it with single stack mags? The pusher seems just fine so I think its the bad geometry of the magazine thats causing your issues. If it feeds reliably with a single stack then that confirms it. 2 pretty pleae may I use a short part of your video as reference in my own video coming soon? 3 it looks like the trigger is not quite conpatible with the stryfe trigger. 4 that zoomy opening :D
@MisterNathan
5 жыл бұрын
1 - Yes, standard mags feed flawlessly. The initial pusher issues were legitimately pusher issues, but the actual feeding issues were the Brick mag' fault. I guess I should've mentioned it, but standard mags performed so naturally that it didn't cross my mind. I was too busy being blown away by the fit of the magwell itself. 2 - Of course you may. (Although I hope I don't regret giving you permission, lol) 3 - Haven't confirmed Stryfe compatibility yet. 4 - Thought you'd like that.
@quapnop1577
3 жыл бұрын
I’m new to this is sawtering nesesary or is there a way around it because I’m a kid who can’t afford or use a sawtering iron
@MisterNathan
3 жыл бұрын
Yes, soldering is required for this kit.
@quapnop1577
3 жыл бұрын
@@MisterNathan so wires don’t have electricity when there’s to sawtering even if they are touching
@quapnop1577
3 жыл бұрын
@@MisterNathan I’m guessing no so that’s ok but where do you think would do it for me
@quapnop1577
3 жыл бұрын
@@MisterNathan I’m guessing no so that’s ok but where or who do you think would do it for me
Пікірлер: 17