To help the cylinder piston to go in and out easier disconnect one of the cylinder hydraulic lines and you won’t be fighting the suction of the piston seals
@AlwaysBored123
Жыл бұрын
That's a good idea. I think the wear ring on the piston was just a really tight fit in the bore here.
@michaelovitch
Жыл бұрын
@@AlwaysBored123 There was vacuum behind the piston,that's why you had difficulties pulling it out. You can see moisture condensate suddenly and exiting the barrel after you pulled the rod. That mean also that seals were good on the inner side,and only outer side sels were damaged.
@AlwaysBored123
Жыл бұрын
@@michaelovitch Oh yeah you're right. I didn't even put that together.
@DieselRamcharger
Жыл бұрын
your chain case has water in it, it gets in from above. then sinks to the bottom. change the oil that sits under your feet.
@DavidSilvia-ms7tk
27 күн бұрын
Nice video, i love these lil loaders
@muddinbronc
Жыл бұрын
The dealer sticker above the 873 decal looks like what’s on my 873. Mine came from Sherwood bobcat of Mankato Mn. Very helpful video. Thank you.
@DieselRamcharger
Жыл бұрын
crack the hydraulic hose fittings loose at the cylinder when pulling the rod out and you wont have suction like that. lmao.
@AlwaysBored123
Жыл бұрын
I'll do that next time. I didn't want to leak oil everywhere.
@lewiemcneely9143
Жыл бұрын
Good fix(s) and those rigs are handy but it takes me a year and a half to get in and out of one. I used to be 6'2" until I got geezerish and shrunk. Blessings!
@AlwaysBored123
Жыл бұрын
I was getting into that particular one the other day and slipped on an oily spot and nearly ate it. They can be treacherous.
@lewiemcneely9143
Жыл бұрын
@@AlwaysBored123 I'll pass but will herd one if can't get out of it. I like your old Case better than any foot controlled rig.
@billjunking_fool5549
Жыл бұрын
Pretty cool I've been out working on my neglected skid steer and I'm about ready to post a video break time for a while👍
@UncleWillie
Жыл бұрын
If you need a place to test it bring it on by.
@mcl237
27 күн бұрын
I have this awesome machine but only in the F series. Recently the light with the gear keeps going on and off when I’m operating. The drive controls are not as smooth as it used to be. Recently I had someone replace the drive seals and ever since then the light has been turning on. Please help
@AlwaysBored123
27 күн бұрын
I believe that light is for low charge pressure and/or high hydraulic oil temperature. Check the fluid level and change the filter if it hasn't been changed recently. Also make sure the hydraulic oil cooler is clean and the fan is working correctly. Sorry I'm not sure what drive seals you're talking about.
@AlanBurnham
Жыл бұрын
I hate it when a puller becomes a launcher. 😂It happens less often now that I've found how useful air hammers can be. If you have a use for beating and rattling severly stuck parts, the Astro 498K is a screamin' deal. What was the tool he was talking about at 10:51? Edit: I just realized you were using a torque multiplier; I didn't even see it the first time. That helps reduce the risk of bending the shaft too I'd expect.
@AlwaysBored123
Жыл бұрын
Yeah I was definitely a bit puckered there haha. I've been wanting a bigger air hammer lately I'll check that out. And yes that was a four-to-one torque multiplier. That's the only way I know of to get really stubborn cylinder rod nuts loose. An impact wrench doesn't work because the rod just absorbs the blows. Thanks for watching!
@AlanBurnham
Жыл бұрын
@@AlwaysBored123 I use a slugging wrench on big stuff. With the opposite end in the equipment and the slugging wrench itself resting on a 22 ton jack stand, a 10 pound sledge makes short work of them. Less than ideal for tightening, but for my shade tree stuff using a center punch on the rod and nut before removal and tightening the nut back to the exact spot is close enough.
@DieselRamcharger
Жыл бұрын
when you go tp pull on the PTFE seals {the yellow ones that dont stretch} hook a zip tie around the seal, flip the zip tie inside out {so the teeth arent against the seal} and use that as a pull ring to slide the seal on with minimal stretching. :)
@AlwaysBored123
Жыл бұрын
Interesting thanks I'll have to try that. Those things were a bear to get on the piston.
Пікірлер: 21