Awesome, thanks a lot. I hope you sleep well tonight knowing there is another roborock S5 driving around with pieces of credit card in its fan motor. For those attempting this: The clips on the fan motor break really easy. I had to resort to a drip of glue to ensure a good seal
@tomasnovotny5892
Жыл бұрын
You are welcome, I'm glad it works and helped you, my sleep will be way better now!!! :-))
@chimeranzl9147
3 жыл бұрын
Genius! Thanks for this - threw in a couple of washers and it did the trick perfect! Also found fluff clogged up on the intake so cleaned the whole inside, it's cleaning the floor ten times better now, just like new!
@stefl0n
3 жыл бұрын
My fan also got stuck the same way and so I was able to repair it easily with your solution. Thanks a lot! :-)
@Mizmodigg
3 жыл бұрын
I can confirm this works. Fixed my fan this way and it is running fine so far. Though, I found a local seller of fan-replacements, so I now have 3 working robot vacuums....
@SonjaL
3 жыл бұрын
Dear Tomik, thanks for the very helpful video! We used BN1074 washers we had left over from our raspberry pi, and they work just fine. Our fan casing clips snapped off when opening them, so we superglued the halves together. Our vacuum is finally working again! The problem presented itself a little differently for us: fan would spin up very slow and after a few seconds error 18 (fan error) was returned. No burn smell, no skidmarks found in the fan. Since we didn't find any debris either we gave your method a try. Good luck to all others with similar issues!
@chrishamilton2694
Жыл бұрын
You're a genius! Awesome video! I wish I had that ingenuity.
@Lopatoid
2 жыл бұрын
Thanks! Roborock S5 was giving me "fan error" and I was able to fix it with a help of your video.
@mattagren
3 ай бұрын
Fantastic!!! ❤
@menangal
2 жыл бұрын
i got exactly the same problem with my robot vac. it sometimes stopped and produced burnt plastic smell. already bought a fan replacement but then found your clip. while waiting for the replacement i tried what you suggested and voila ... it worked like magic!! the robot vac is now back like a brand new one. i will keep the replacement for spare. thank you very much for sharing!
@patrickgorham966
3 жыл бұрын
Worked GREAT, Many Thanks!
@danijel124
2 жыл бұрын
Thanks this actually works. I used metal m3 washers. I couldnt remove the stator like you so i just placed it underneath somehow and it works again :) thanks
@robertcmarko1829
3 жыл бұрын
Thanks Tomik723, This definitely works for me. I made those distance parts from shirt collar stay, which is thinner than and I found it better this way. Good job!
@robertcmarko1829
3 жыл бұрын
...thinner than plastic card...
@vanameintani3708
2 жыл бұрын
Thank you very much! You are great!
@vithayab2286
2 жыл бұрын
I have the model vacuum + mop 1G. Seems to a be another version. Bought mine 1month ago, it was working well until today. I did the same trick with the fan and it worked ! 1g fan is black, not white. Thank you for your tutorial
@Tomik723
2 жыл бұрын
You are welcome, I’m happy, it worked for you too.
@tobybrown1179
2 ай бұрын
My fan glued itself together on the flange near the motor. I had a new fan to exchange it over so just threw it away, after pulling it apart to check it out. Yes the tags broke off easily as I pulled apart
@Skans-Gustav
2 жыл бұрын
Beautiful solution! Thanks.
@shaundramann9161
2 жыл бұрын
God bless you! Thank you!
@NhanHuynhDo
2 жыл бұрын
Another success story. I used layers of toilet paper instead of washers to have more control of the thickness. Thanks Tomik723 for the tip!
@Tomik723
2 жыл бұрын
Good idea! Anything with needed thickness can be used :-)
@alptekinkaratas1772
3 ай бұрын
thanks a lot.
@danijel124
Жыл бұрын
I repaired 4 roborock s5 this way and they work as new after 1 year :P Thanks mate
@tomasnovotny5892
Жыл бұрын
Thanks for feedback! I'm glad it helped! :-)
@ivanj0
3 жыл бұрын
Well thought!
@viniciusperotto594
2 жыл бұрын
I must have done something wrong. One of the clips broke, then I put the washers and closed the vacuum. When I turned it on the fan started making a very loud noise and it didn't look safe to let it run with that noise, so I sort of gave up and let the robot to die alone in my living room. Later I ordered a new fan from aliexpress, which was like $10, had a coupon so it cost me $3 with free shipping. I kept the original fan, if the new one breaks I will try your fix again! Thanks for sharing the video :)
@Tomik723
2 жыл бұрын
Did you checked if the fan seats well in position without freeplay? I don’t know if housing connection is tight enough when one clip is broken, but you can always weld or glue it (disassebly will be more complicated next time, but it will serve the purpose).
@robi7155
2 жыл бұрын
Hi Tomik, thanks for this video *thumbsup*, i had the same problem and i could solve the problem. My Roborock smelted like it was a electronic failure, but after i saw your video i checked this little guy. And what can i say....... see it, say it, fix it and it works like new!
@joelity
2 жыл бұрын
I opened the fan and found that the motor core and the blade was not firmly attached to each other. When the blade spinning, it floats up a little bit till stuck to the fan cover. My working solution is using super glue to attach the fan blade and the motor core. Making it stick together. The robot is working just fine.
@njmaverick7
3 жыл бұрын
Hey @Tomik723, I was wondering if you know the pinout for the motor connector on the board. I believe one would be +14V, GND, two others for the direction I/O.
@ptomi75
2 жыл бұрын
Thanks!!!
@cescsoo
Жыл бұрын
good idea👍
@Mizmodigg
3 жыл бұрын
This looks just like mine. I had noise in addition to the smell. Did it work fine after your fix?
@alexmendel1324
3 жыл бұрын
nice guide, made same with my old original engine after watching your video. Can't test helped this or not until my current engine die, too lazy to disassemble robot again just for tests :/ But already touched this previously floppy detail, it not loosy anymore, seems legit! Sad that I've found this video too late and already buyed new engine from aliexpress... What have you used to open those clipses? I've break two of them at opening
@wongndeso7884
Жыл бұрын
👍👍👍👍👍👍👍
@khanhsmarttechs
3 жыл бұрын
Can it work on S5 Max, S6 MaxV ? tks
@BOTmaster15
2 жыл бұрын
3d printing one custom washer would be much easier to assembly. Mine is still workign but sooner or.later I might have to do this
@tomasnovotny5892
2 жыл бұрын
Thanks for feedback, glad it works! :)
@tubaengin
3 жыл бұрын
I have been using s5 for 1.5 years now and it alvays gives error 10 like 2 minutes after it starts cleaning. It decreases the suction power and does not clean as good as before. Also it keeps calling for error 5 during cleaning like every 5 minutes. It complains more than me during cleaning 😅 i disassamble it till the fan and cleaned all filters but nothing changed. Do you have any suggestion about what to do? Thabk you for thr video, i will try of it helps for our case..
@Tomik723
2 жыл бұрын
Uff, unfortunately no idea, sorry. So far I had a trouble only with a fan.
@pinidpm
2 жыл бұрын
Hi, I had the same problem than you. I cleaned my roborock and after 1 minute cleaning, the Error 10 appears again. I changed the vacuum motor of a new one and the problem was fixed!
@tubaengin
2 жыл бұрын
@@pinidpm thank you. I try it too. It is quite expensive nowadays because of the currency rate but insallah I will try it in first opportunity.
@andriuspajarskas1084
Жыл бұрын
simple and good solution, funny indian accent too :)
Daha kolayı. Motor milinin girdiği yuvanın içini temizleyin. Bunlara gerek kalmıyor.
@Mrlwindows
5 ай бұрын
когда он начнет работать он опять опустит вниз
@wizard-of-other-oz
2 жыл бұрын
Did not help. It seems the magnets cannot hold the turbine in place
@pjaymaen
Жыл бұрын
I removed the 3 screws but cant remove the pcb from the Fan?! How to remove the pcb?
@sagarspatil
Жыл бұрын
Same problem with my Roborock s5 max. Can’t separate the circuit from the fan.
@zsoltkallos437
Жыл бұрын
@@sagarspatil same here. did you find the solution?
@sagarspatil
Жыл бұрын
@@zsoltkallos437 yes. Watch the video in slow motion and follow it closely. I’m not sure how to explain it.
@zsoltkallos437
Жыл бұрын
@@sagarspatil can you try to explain, still cannot disassemble :(
@elczupakabra8993
9 ай бұрын
I had the same problem, but I have just used more force and it finally came off. To not break anything just hold the metal part on the PCB and the base part of the fan (closest to the PCB) as the top part can be dismounted.
@karelkomarek7322
Жыл бұрын
Dnes jsem vysavač celý rozmontoval a stejně to moc nepomohlo. Spíš vůbec. Asi budu muset koupit nový fan.
@tomasnovotny5892
Жыл бұрын
Zdravím, ano je to tak, někdy už nic jiného nezbyde. Ale berte to tak, že aspoň máte natrénovanou demontáž :-)
@karelkomarek7322
Жыл бұрын
@@tomasnovotny5892 jo to jsem si taky říkal že teď to dám bez návodu. No snad je to tím. Nwm jestli to koupit někde na wishi🤔
@karelkomarek7322
Жыл бұрын
@@tomasnovotny5892 předtím se jen zapnul, zavrčel a hlásil chybu 18. Teď už jezdí ale nevysaje nic a trochu to v něm píská.
Пікірлер: 59