while still waiting to receive my M1, I am investing my wait time in learning from Michael's videos. these videos are precise, to the point, long enough to get to the point but not to get you bored. and Michael, I tell you, I am learning a lot, and what I like most is that you go to extremes and (in some other videos) you do some things that I wouldn't even think of doing :)
@scubajenn5
2 жыл бұрын
GREAT info! I didn't know what the "framing" was for! Thx Michael!
@user-iw1bq6qj7z
8 ай бұрын
I'm so glad I watched this video, I am struggling lining up my graphics on a keyring, it's printing on the side now I know how to frame I shouldn't have a problem 🤞
@paulmartin5537
Жыл бұрын
Great info thanks for going through how to use the M1 in such an easy to follow way
@denniscoddington1701
2 жыл бұрын
Another GREAT video!
@J0BeKillinEM
2 жыл бұрын
What an amazing video
@vincentdimaggio5627
2 ай бұрын
Great info Mike. We have the honeycomb and riser base and are trying to engrave in a recessed ring box. The laser hits the side of the box. Not sure what we need to do
@efratdalton452
11 ай бұрын
Hi Michael, Love your videos, thanks for creating them! New to laser cutting. I just got Rubber Wood 3/4" cutting boards that I would like to engrave them for the holidays. can you recomend setting or what I should start the testing at? I don't have a scrap that I can do a lot of testing. Also can I rase the bored with books underneath when I'm engraving. I have the honeycomb but I still need to rase it. thanks for all of your help.
@TheBestUni
5 ай бұрын
❤❤
@craftandreviews5091
2 жыл бұрын
I am wondering if you have any templates for the air assist for M1
@ericawilliams18
2 жыл бұрын
I don’t have the M1 ,I have the D1 yet knowing the settings help
@MonkeyWoodworks
2 жыл бұрын
❤
@VengD
2 жыл бұрын
My software don't have a Path Preview button?
@MrGhostface316
Жыл бұрын
Hello, I appreciate your really great videos. My M1 is now marking my tumblers with the framing option. The power is set at 1 and the speed is 100 on framing settings. I did the first tumbler and the framing worked fine no marks left second tumbler exact settings left a square mark around the framing area. Very noticeable actually the tumbler can't be used for the design now. Very odd but was wondering if you had any ideas about what it could be? I tried this several times by restarting and checking settings I cannot find the issue. thank you for your time. I can provide pics if needed
@xToollaser
Жыл бұрын
Could you please provide the picture?
@cameron.carranza
Жыл бұрын
Mine did this too, I have seen other videos where they say to not auto measure and leave thickness at 0 for framing otherwise it will etch but have not tried it yet
@bernicetyms5391
Жыл бұрын
Hi thank you for your videos.I’m currently waiting for my M1 to be delivered. But I have been viewing your tutorials while waiting. My question is how do you know how much power and speed to use? Dose the software comes with a preset or do you just by trial and error?
@xToollaser
Жыл бұрын
We do have a project center on software that have all the parameters set up.
@mozie38
2 жыл бұрын
Where did you get the camera for your laser
@xToollaser
Жыл бұрын
Hi @Leon Mozie, it's xTool M1: bit.ly/3c1G4fk xTool M1 is the world's first hybrid laser + blade cutter & engraver with camera
@moniquevann9950
Жыл бұрын
Can u engrave and cut on the M1
@xToollaser
Жыл бұрын
yes you can
@jackiespino3440
Жыл бұрын
can u do a video showing how to engrave on a knife?
@aimeehuang7184
Жыл бұрын
Thank you so much for your suggestion, we will consider it!
Пікірлер: 24