Don’t use marine grease on the impeller. It will cause the impeller to break down over time. Use Dawn Ultra dish soap.
@rumblethis2023
Жыл бұрын
Would be a good idea to mark the trip tab position
@goaheadmakeourdayscooterpe9644
2 жыл бұрын
The grease is a good idea for first start and will be flushed out in no time and won't hurt the rubber impeller. Also a good indicator is when motor at idle and flow out of pisser is slow change impeller.
@alcrockett2933
Жыл бұрын
Change oil in a 60 hp Yamaha outboard motor
@TheMarpalm
Жыл бұрын
Good video - very helpful in replacing my impeller. Just a couple of lessons learned: 1.a note where the bolts come out when removing the lower unit. There are two different sizes 1. It is helpful to clean the drive shaft before pulling the impeller. Also used some dish soap to help it slide up. 2. My impeller was very tight going on. Used a piece of wood and small rubber mallet to help move it along. 3. Be careful not to score the shaft with screwdriver. As soon as I got the impeller moving I switched to a plastic tool that is designed for removing interior parts. 4. Used dish soap to help the impeller slide into the cup. Very helpful suggestion someone else made. 5. When putting the unit back together make sure you get the spline for the shifter into it’s shaft (hole). There is enough play in the upper piece that the unit will go together with the shifter not properly engaged
@Adogsmate4267
Жыл бұрын
I was taught that way as well, but use vaseline instead. That's the same bottom end as the two stroke 90, old saying, if it ain't broke, don't fix it.
@peted5217
6 ай бұрын
Nothing likes Dry Insertion
@joshbert2062
2 ай бұрын
Thanks for the refresher Josh , now come out to the camp and fix or generator ! (Echo lodge) 🤣
@aquariun21456
3 ай бұрын
Why Didn't you replace the Water Pump Housing Gasket??
@retiredguyadventures6211
Ай бұрын
So there is a notch inside the cup but you didn't bother mentioning were to line the notch up with in the housing?
@eltonjeans7394
3 ай бұрын
What happened to black o rings ? That needs to be installed? ???
@rpeek
Жыл бұрын
Nice video, thanks.
@RCast-sc6fy
Жыл бұрын
Thank you so much for making this video! You’ve saved me hundreds this year and thousands in the future!
@waynebosman9023
Жыл бұрын
Never did hook up the pitot tube...
@joemassey9383
2 жыл бұрын
Great video. Replaced everything like you did to the letter, water flowing great, but prop will not engage when put into gear (water hose in the driveway ... for what that's worth). Did I miss a step? Quite sure the splines in the shaft lined up or the lower unit would not have bolted back up would it? Thanks
@Schneids15
2 жыл бұрын
Hey Joe! 100% you missed the splines on the shift shaft when putting it on. It’s a pain but yank it off and move it to neutral (pliers), you’ll feel the detent and spin the prop free. They are a PITA to throw back on nice.
@27fabre1
Ай бұрын
Made this job easy, only thing is my prop is free spinning and won’t engage. I’ll have to drop it and figure out how to line up the splines. 90hp Yamaha
@Schneids15
Ай бұрын
@27fabre1 hey, yes you have missed the shift shaft to line it up. Take your time and you will get it. In all the one’s I have done they can be a real pain and it would not be the first time I missed one putting it together. Good luck.
@jonkarle8670
11 ай бұрын
I'm having troubles getting the outdrive to go into the upper part of the motor. I get to within 3/8" of going together and it won't go any further
@Schneids15
11 ай бұрын
Be sure the water tube is lining up . Some lube on it helps sometimes. Also make sure splines are clean.
@jonkarle8670
11 ай бұрын
I lubed the water tube and shifter splines as well, not sure why it won't go past 3/8" together
@samuelramosnieves3280
2 ай бұрын
It has a new inpeller and does not have much water precion
@Schneids15
2 ай бұрын
Could have a blockage. Check thermostat and pee tube and make sure they are free of debris
@bro.weaver1282
3 жыл бұрын
Is this a wear item?
@Schneids15
3 жыл бұрын
That’s correct. They recommend changing them every 100 hours or yearly. Many go for years without changing. They are supposed to stay nice and springy and should spring fairly straight if the impeller housing was pulled off. Eventually they get hard after use and take shape of the cup like the one i pulled out and they will either shred and clog the water passages and cause an overheat or can just become so taken to shape that under high speeds they cause an overheat. Most of the time they shred and the motor gets a severe overheat. That is why you change them regular to prevent it👍🏻
@andrewhochstetter4542
3 жыл бұрын
Where does the O ring go that comes with the rebuild kit?
@Schneids15
3 жыл бұрын
Some go on top of the impeller. All models are different
@6mallards
Жыл бұрын
Great vid what year is that engine
@Schneids15
Жыл бұрын
Thanks. 2011
@6mallards
Жыл бұрын
@@Schneids15 I'm guessing it would be the same for a 2017
Пікірлер: 30