How much for this whole kit? Looking into getting this done on my 19 Ranger 900. Only has 400 miles but I’m sure this kit would be good for it anyway.
@utvgarage
5 ай бұрын
This kits runs starts around 500 from gilomen but will go up depending on what add ons you get
@PDK7777
7 ай бұрын
Will bad rollers ever cause it to make a slight metal sound when under mid load?
@utvgarage
5 ай бұрын
Very possible. I am to the point now were you’re better off throwing the clutch away and replacing it with a new one . I use mother clutcher on almost all replacements . Polaris clutches are disposable in my opinion
@RobPB8
Жыл бұрын
Thanks for the help big dog! Good video.
@Mcgheen2670
Жыл бұрын
Great Video, thanks for the info. How has it held up over the past 10 months? A few buddy’s of mine rebuilt their clutches and had nothing but problems afterwards, didn’t last but another 500-1000 miles. They decided to run the cheap throwaway clutches instead as the cost was the same to rebuild vs buy the new full complete cheap clutch.
@utvgarage
Жыл бұрын
Thanks! Depending on how far gone the clutch is depends how long it will last. I’ve seen a few clutches in excellent shape that only have sloppy rollers. I typically leave it up to the customer on what they want done , but most would rather install an aftermarket clutch vs paying labor cost on a rebuild. If the clutch shows wear in other places I would typically recommend a replacement clutch
@SickoModeTravisScott
Жыл бұрын
Nice super atv
@jeffsturgeon3849
Жыл бұрын
NICE
@alanivmontano
Жыл бұрын
Sooooo is it possible to remove the pin in the rollers with a hydrolic press??? No one shows the removal process of that pin without beating the hell out of it with a sledge and a punch
@utvgarage
Жыл бұрын
Yes use a small bolt and a socket to press it out
@justinbolton2838
Жыл бұрын
how did the hd bearing last over time
@adamaustin3373
Жыл бұрын
did you do the ECU tune also? how much difference did this make etc?
@utvgarage
Жыл бұрын
Yes the ECU tune paired with the clutch kit is a big improvement on the Ranger and the General
@adamaustin3373
Жыл бұрын
@UTV GARAGE does it make your RPMs crazy high? stock they run like 6200 at 55mph etc. would you do it over again?
@utvgarage
Жыл бұрын
It comes with two primary springs. One will lower the rpm’s. I’m running the higher rpm spring in my crew cab and rpm’s are high but they level out one I get up to speed .
@adamaustin3373
Жыл бұрын
@UTV GARAGE so even with the higher RPM spring, it's not any worse than the stock once I get up to speed....I also have the crew cab. Just looking for a little more top end speed for when I take the family out joy riding etc. We have ours street legal. Kind of a do it all, farm work, trails and road.
@jessefields9535
Жыл бұрын
Many other professional sxs mechanics say DO NOT USE brake cleaner on these parts.
@PhilBilly21
Жыл бұрын
No loctite/threadlock required? Great video by the way!!!
@utvgarage
Жыл бұрын
No loctite
@carolbogle7673
Жыл бұрын
Hi dad 
@utvgarage
Жыл бұрын
Yea I do 😂
@williamevans3939
Жыл бұрын
you need a camera man!
@utvgarage
Жыл бұрын
Be sure to use loctite on spider . I diddnt get that step in the video
Пікірлер