All in around 12k. That's the boiler, 2 pumps, 150' of pipe, plate exchanger, heater in the barn, and misc. fittings, wire, and thermostat for the barn.
@oldandintheway9805
7 ай бұрын
As a three year owner/operator of a 7200MP model, I offer one other piece of advice/warning; NEVER NEVER open the door without making sure you are standing off to the right side, and back away at arms length when the stove is burning. Especially when it has been idling (fan not blowing) for a while. Mine, on occasion will back draft, and belch a ball of fire out the front that would roast you if you were standing in front of the open door. If you don't know what a back draft is, watch any of several youtubes on back drafts. Firemen learn about them on their first day in fire school.
@Spudd74
7 ай бұрын
I always check the water temp make sure I hook the u-bolt with the latch any time I open it. I'm a career fire fighter and understand fire behavior and backdrafts, but I appreciate the advice and tips. Thank you.
@oldandintheway9805
7 ай бұрын
@@Spudd74 Come to find out, either the newer models or the older models ( I don't know which my model is) had a damper rod on the front that you opened before you opened the door to eliminate that potential. Mine has no such thing and I've had it belch out a fireball several times.
@Spudd74
7 ай бұрын
@@oldandintheway9805 mine has the rod.
@jwcautomotiveservice5861
11 ай бұрын
Sweet find. How much did you end up paying for it? I’m looking to purchase one soon but prices are all over the place
@Spudd74
11 ай бұрын
I didn't get a deal on it. lol. I paid $6k for it. All original and titled, I was good with that.
@ok2x
Жыл бұрын
Do you feel now that your have ran this an entire season that it is better then just a wood stove in the house? How much smoke are you getting each time you load it. I hate breathing and smelling smoke. Im at the point now where i have to decide for this boiler or soap stone wood stove.
@Spudd74
Жыл бұрын
Yes, I do like it a lot better than a wood stove inside. The mess it outside. No worries of my house catching on fire from that random hot ash or from the stove burning too hot. I don't have to split my wood as small and with my stove I can burn pine and other soft woods if I get into a pinch it doesn't have to be seasoned. I do burn more wood with the boiler than I did with a wood stove, but I don't mind, I enjoy cutting firewood. As far as how much I get when I load it. You do get some smoke coming out, but it all depends on if you give it a minute when open the the dampener and crack the door. Also depends on where you are in the burn cycle, if it just reached temperature or if the blowers are getting ready to kick back on. The type of wood and how seasoned it is will affect the smoke. So yes smoke can come out but its outside so its not smoking up your house.
@jwcautomotiveservice5861
Жыл бұрын
Sweet buy! Enjoy
@Spudd74
Жыл бұрын
Thanks
@davethebeagler7711
Жыл бұрын
Good for you!!! That is an awesome find. You can’t do any better than that.
@Spudd74
Жыл бұрын
Thank you
@johnk5193
Жыл бұрын
Thanks can you do a 2nd year review also?
@Spudd74
Жыл бұрын
When the weather breaks and I get some time.
@smackie0178
Жыл бұрын
Nice! it reminds me of my 86 & 87 when I got them.
@Spudd74
Жыл бұрын
Thanks
@theshanipaqman
Жыл бұрын
How many cords did you burn and what size s/f you heading? Thanks for sharing
@Spudd74
Жыл бұрын
From October until late April early May I’d say around 10 full cords. That’s heating around 2000 sq/ft and our domestic hot water. Keeping the house around 72*. The only time I run the heater in the barn is if I’m out there working. I probably burned a couple more cords over the summer heating the pool and still doing the domestic hot water.
@andrewgerace8539
Жыл бұрын
wow really looks good all stock like that
@Spudd74
Жыл бұрын
No quad will ever look as good.
@stephengalvan7722
Жыл бұрын
WOW that's awesome 👍
@Spudd74
Жыл бұрын
Thank you. I’m afraid to ride it. Lol
@stephengalvan7722
Жыл бұрын
Because of power or cleanliness that thing was intended to ride just be careful always wear your riding gear that thing is very torquey
@Spudd74
Жыл бұрын
@@stephengalvan7722 cleanliness. It’s all original. It would break my heart to get it dirty. Lol
@ronaldtartaglia4459
Жыл бұрын
Welcome to the club. What a beautiful machine. kzitem.infoMVkeS409mXE?feature=share
@ronaldtartaglia4459
Жыл бұрын
Absolute work of art. THE most beautiful quad ever built.
@Spudd74
Жыл бұрын
I agree completely
@spuddtheepicanimator7252
Жыл бұрын
Surprised you haven’t made a vid on the other one
@Spudd74
Жыл бұрын
Not as cool
@ttatvoffroad2632
Жыл бұрын
Gotta give love to the short rod cranks!
@Spudd74
Жыл бұрын
Heck yeah. Love everything about it.
@jamesmiller7283
Жыл бұрын
Wholy shit them dogs look badass ! I mite hafta order me a set .
@Spudd74
Жыл бұрын
They are badass!!!!
@spuddtheepicanimator7252
Жыл бұрын
Nice!
@Spudd74
Жыл бұрын
Thanks bro
@truckguyjoe
Жыл бұрын
Badass
@Spudd74
Жыл бұрын
You should see it in the back of an Alaskan!!!!!
@dentondunn4346
Жыл бұрын
Is the 362 a prosaw?
@Spudd74
Жыл бұрын
Stihl has it under their professional line.
@spuddtheepicanimator7252
Жыл бұрын
This epic
@Spudd74
Жыл бұрын
You’re epic
@spuddtheepicanimator7252
Жыл бұрын
Thx
@JimmY-jf3rw
2 жыл бұрын
How often do you load? What area are you in? 10 facecords or 10 cords did ya burn<30face>?
@Spudd74
2 жыл бұрын
I load it twice a day. When I do load it’s never full. I just throw 5-6 chunks in. I’m in northwest Pennsylvania. Up by Lake Erie. I burned 10 full cords. I’m still burning it to heat my pool and domestic hot water. Heating oil is too expensive right now. Lol
@outdoorswithlarryrobin
2 жыл бұрын
Hello just subscribed, nice Modifications, Take Care and Stay Safe 🚜🪵👍🏼🇺🇸
@Spudd74
2 жыл бұрын
Thanks Larry.
@adelarsen9776
2 жыл бұрын
Why do you need a new side cover plate ? I don't understand. Thank you.
@Spudd74
2 жыл бұрын
Honestly I don’t remember why. The kit came with it. If I get a few minutes I’ll take a look.
@adelarsen9776
2 жыл бұрын
@@Spudd74 Thank you. The man does not seem to have a website.
@Spudd74
2 жыл бұрын
West Coast Muscle Saw is where I got it from.
@fjb5263
2 жыл бұрын
I am getting a 7200 mp this spring. Thanks for the review
@Spudd74
2 жыл бұрын
Awesome. You’re gonna love it. It’s a little frustrating until you get a good coal bed. Also I learned to keep the blower turned way down and than I didn’t have any problems with it going out, even on the warm days.
@fjb5263
2 жыл бұрын
Thanks I am in NW PA to how much wood did you go through last year?
@allanmingee9870
2 жыл бұрын
Just watched this video,It is definitely louder and more robust in how it sounds with the bark box installed,Also it does seem to have a bit more power and speed from just that simple breathing advantage,less turbulence means improved performance,I just ordered Dogs and Barkbox for my 362C.These saws auto tune in just a few cuts to the changes in breathing,It’s nice to have no tuning screws to have to readjust👍🏻
@Spudd74
2 жыл бұрын
I don’t think you’ll be disappointed with the dogs or the Bark Box.
@allanmingee9870
2 жыл бұрын
@@Spudd74 I don’t think so either
@SUROBLEDEKchannel
2 жыл бұрын
Great video sharing 👍
@Spudd74
2 жыл бұрын
Thank you
@SUROBLEDEKchannel
2 жыл бұрын
STIHL chainsaw is really good
@Spudd74
2 жыл бұрын
I agree. Nothing against other brands, I’ve just always owned Stihl.
@tomplucknette5941
2 жыл бұрын
It is clearly faster with the bark box, gets up quicker and is quicker in the cut. 3 things to improve a stock saw markedly... muffler mod, base gasket delete, advance timing, square grind your chain. This will double a chainsaws production.
@mikebrewer7776
2 жыл бұрын
Hey there. Did you let the CM recal itself? Sounds good.
@Spudd74
2 жыл бұрын
Yep. It’s been running great and starts no problem.
@tech-gl8po
2 жыл бұрын
Sounds like it's cutting slow or your not revving it mine will absolutely eay
@jonahmelchosoutdoors5006
2 жыл бұрын
Question will the old cover still fit with wrap handle?
@Spudd74
2 жыл бұрын
I’m not sure. The kit came with a new cover so I’m guessing it won’t.
@jonahmelchosoutdoors5006
2 жыл бұрын
@@Spudd74 oh ok I’m looking into the kit but I want to keep the captured nuts and someone told me the other cover that come in the kit is better because it doesn’t clog with saw dust
@racerx9223
2 жыл бұрын
Hopefully you reset it, I'd imagine you did.
@robmatthews4259
2 жыл бұрын
Defiantly sounds and looks like it cut way better with no bog, thanks for the video my Barkbox is on its way 👌
@Spudd74
2 жыл бұрын
Heck yeah. You’re gonna love it!🤘🏼
@bkb5668
2 жыл бұрын
I have three of these saws one with an Egan straight shot one with a bark box and another stock muffler. Two of them are set up west coast style the other has the normal handle bar and clutch cover. I have a nice 441 and new 500i that are both set up west coast also. I put a bark box on the 500i. Put a tank/handle guard on that saw, it really cuts down on bottom rash. Thanks for the video!!!
@Spudd74
2 жыл бұрын
Dude, not gonna lie, I’m a little jealous of all your saws. Thanks for checking out the video.
@jimmyfaherty8588
2 жыл бұрын
it looks bad azz. doggs are really 👌. not sure if it was chain or your muffler upgrade. but, it seemed faster(muffler upgrade)
@Spudd74
2 жыл бұрын
Yeah it does look pretty sweet. The chain is stock and I thought the same after the bark box was put on but I just figured it was me hoping to see a difference. Lol
@adrianstefan23
2 жыл бұрын
🙉🙊🙈👍👏
@bradenmiller3476
2 жыл бұрын
Did you have to reset the tuning on your mtronic after you put the muffler on? Do you still like the bark box?
@Spudd74
2 жыл бұрын
No I did not have to reset it. With the mtronic it will adjust itself to changes in air coming in and going out. Yes I love the bark box. It sounds awesome. Just the right amount of bark.
@etthealiengamer
2 жыл бұрын
My boss did mine because he has a buddy that it is certified Stihl they had to rest it and and its mtronic shit this saw has the power
@timtorkelson7201
2 жыл бұрын
Got one on my 462..love it. Instructions read if mtronic it learns itself,usually after 2nd or 3rd cut.
@etthealiengamer
2 жыл бұрын
That is the bar length from the end of those felling dogs to the tip of the bar
@Spudd74
2 жыл бұрын
Sorry, I just saw the comment. I’ll measure it tomorrow. I’m guessing around 18”
@Aaron_A_Lynch
3 жыл бұрын
Nice freaking saw buddy..love the mods..👍🏻🤘🏻🪓
@Spudd74
3 жыл бұрын
Thanks dude.
@IndianaDoug
3 жыл бұрын
Thanks for the video man. I looked into the 3/4 wrap handle like yours and could not believe the price. The bad thing is there are no aftermarket wraps for the 362. I retro fit something I paid $45 for. Looks and feels completely stock. I'll make a video of it on my channel soon...
@Spudd74
3 жыл бұрын
Yeah I t was expensive. I looked at it a bunch of time before I ordered it. I might of even had a couple beers in me when I did. I have no regrets. It made dropping trees easier and more comfortable. I’d like to see your video.
@IndianaDoug
3 жыл бұрын
@@Spudd74 🤣 we could be friends!
@Spudd74
3 жыл бұрын
You can never have too many friends!!!!
@danr308
3 жыл бұрын
PLEASE make that video!!!
@danr308
3 жыл бұрын
Cause $289 is as much as I paid for the saw!!!
@BLAM777
3 жыл бұрын
Had any problems with the m tropic wireing breaking and the saw just dies while running? Just got one and now I'm finding out that if you run it alot it just keeps heating up the wires and breaking them.
@Spudd74
3 жыл бұрын
No. I haven’t had any problems.
@kurtismoosman8039
3 жыл бұрын
I have just bought the bark box mufflers for my 362c and 461, they sound mean.
@Spudd74
3 жыл бұрын
Yes they do
@ashtoncooper9269
3 жыл бұрын
That sounds sweet
@Spudd74
3 жыл бұрын
Especially at an idle!
@bondtanna99
3 жыл бұрын
I haven’t seen where they offer the full wrap handle can you post a link? How much was it? Thanks in advance
@Spudd74
3 жыл бұрын
The wrap around handle was from West Coast Muscle Saw. I would add a link but I don’t know how too. I just checked and it’s still on their site. The kit wasn’t cheap $289. It’s all Stihl parts. It made a big difference when felling trees.
@kylebrown8891
3 жыл бұрын
When I go on wcs they label a bark box for only ms360 and 036. Is that what you ordered. I have a ms362 c that I’m not to impressed power wise.
@Spudd74
3 жыл бұрын
They have it listed in the drop down box for 362/400 and it has to be a 2 piece muffler.
@kylebrown8891
3 жыл бұрын
@@Spudd74 ya I have the two piece. Did you take any precautions to let the saw auto tune? I don’t know a lot about the new saws.
@Spudd74
3 жыл бұрын
I did not do the reset. Everything I read said that will adjust itself during normal use.
Пікірлер