Find a fix for this? on my 2017 i have taken everything apart cleaned and greased and it still sticks real bad
@romanbrouwer9412
2 жыл бұрын
Hi Micheal. Did you manage to find a fix for it in the mean time?
@vuikaa
5 жыл бұрын
I think i have the same Issue on my 2019. what are the syntomes of a stuck power valve? I have no power in low rpms. When i quickly get on the throttle i almost Stall the bike
@danmarkfordanskere
Жыл бұрын
pls answer me bro! did you find out what made it
@MrDanny7686
Жыл бұрын
@@danmarkfordanskere did you get yours sorted I've got a 2019 ktm sx 125 .. the power valve was sticking mid range I took bothe valve covers off sprayed wd 40 and cleaned them .. then adjusted the power valve arm up and it seemed to work
@danmarkfordanskere
Жыл бұрын
@@MrDanny7686 narhh i dint got it working... its a bit harder to start it and it dont runs top speed😬
@willc44
4 жыл бұрын
My 2014 sx 250 has this problem. Gluggy midrange power. It also Oozes at that cover. Any help on fixing the issue would be great thanks 👍🏻
@electricaltech70
2 жыл бұрын
Does it ooze at top of cover?
@2wheels4life27
7 жыл бұрын
what happens when the bike is off and u just move it up and down with ur fingers , does it move the same way it does in the video and the pin rides thu that u shaped cut out?
@electricaltech70
7 жыл бұрын
Well about 3 times out of 20 open/closed it will try and stick at the half way point.
@2wheels4life27
7 жыл бұрын
ok so mines really bad then , i try movin the outer powervalve with the pin that rides thru the u shaped arm and it dosent wanna move at all, maybe only like a mil or 2 of play, i can only move the arm with the spring from the bottom of the u shaped arm to the middle of the u shaped arm it wont go thru the bend of the u shape cause that part dosent wanna move , but the bike runs really good which is weird , it maybe only stumbles to get on the pipe a bit sometimes in 1st and 2nd all other gears it rides awesome , and ya it dosent happen much in 1st and 2nd even.
@electricaltech70
7 жыл бұрын
it hard to move by hand you need to take a socket or screw driver with a t adapter not sure what size and stick it in the bolt holding the arms together and when you try to loosen or tighten it will operate the powervalve.You can't really move it by hand
@2wheels4life27
7 жыл бұрын
Daniel Kendrick ok
@picklito
6 жыл бұрын
I don't see it sticking in this video. What am I missing?
@bloomerb4162
2 жыл бұрын
My friends 2019 ktm 125 doesn't want to easily get in the power band. It's like when it should hit, I have to hold it wide open and wait an extra couple seconds, then if finally breaks thru. Also it's way worse in first gear and second. Is this what you were experiencing?
@electricaltech70
2 жыл бұрын
That’s exactly what mine was doing.
@bloomerb4162
2 жыл бұрын
@@electricaltech70 oh I see you used the JD kit. That's the first thing I thought it was, the carb. So I actually haven't ridden it after the carb kit bc it was wrecked, bent sub frame.
@peterryan9951
Жыл бұрын
How did u fix this my husqvarna tx 125 had the same problem
@bloomerb4162
Жыл бұрын
@Peter Ryan you need a #6 slide and jet it leaner with the mikuni. I put a keihin in with jd jet kit and a red power valve spring.
@2wheels4life27
7 жыл бұрын
are you pinning it ,and it just wont get on the pipe?
@electricaltech70
7 жыл бұрын
At the beginning I have it nearly full throttle.Rest of video is off and on full throttle
@yamahonda400
7 жыл бұрын
so how did you fix it?
@electricaltech70
7 жыл бұрын
Honestly I haven't yet.I just put a jd kit in and it still has the same issues I went with rich settings so Next ill try to lean it out
@yamahonda400
7 жыл бұрын
we have found blue needle, middle clip. it runs flawless. ours ran just like your is until we did the jd kit. we are at 1000ft with our settings.
@electricaltech70
7 жыл бұрын
yamahonda400 what size pilot jet did you use?
@yamahonda400
7 жыл бұрын
32.5 pj and 450 mj
@electricaltech70
7 жыл бұрын
Okay I used the 37.5.I'll try changing mine to that too.Thanks!
Пікірлер: 36