great video, helped me out. I didnt know big ball and spring had to be compressed prior to pushing on grooved collar, thanks
@davidestelter1092
3 жыл бұрын
10 fold here and twice to the repair shop and a couple hundred dollars later for stuff i didn't need! dumb and not to bright for that simple tid-bit of the unknown....? lol lesson learned from some one who took the time to post this wonderful information to help others! A BIG THANK YOU FOR YOUR TIME AND EFFORT TO HELP OTHERS....!
@stevesobolak2416
Жыл бұрын
I used grease to hold in them little bearings during assembly. They are 7/32" just in case you drop one and most bicycle shops have them. Water gets into my valve where it is assembled, so I put some permatex on the mating surface. Awesome video !
@trevorstevens3469
5 ай бұрын
How big was the big bearing? I used 10mm but I think it might be too small because the detent doesn’t hold
@philliphall5198
7 ай бұрын
Frac mechanic here and I miss repairing hydraulic systems very much, loved the blender, most expensive hydraulic system in fracing, cement mixer was the next best option for fixing the problem with hydraulic system
@JoseMartinez-no2vb
Жыл бұрын
Great video. Thanks for your insight. My Erien log splitter is now running.
@stevenmccoy135
2 жыл бұрын
Great video - our log splitter is now up and running. Thank you!
@pencorco
7 жыл бұрын
Great Video!
@steelthunder76
10 ай бұрын
Awesome video and I don't say that often thank you very much
@chadkeever9437
Жыл бұрын
dude.........this was so helpful! especially at the 4:27 mark ! exactly what a guy needed! thanks alot buddy!
@tommcdonald53
2 жыл бұрын
Thanks so much for this video as I had to do this with mine, the valve was sticking and had to clean it out and I think it will be fine after I'm done.
@heynanenaner
7 ай бұрын
Very nice! thanks for the help...
@aramstudio2891
9 ай бұрын
Very helpful video. My detent was sticking and I wanted to adjust the nut but accidently 4 small bearing balls flew out of detent sleeve and when I found them I couldn't find right diagram to put all together in right order so I made a mistake by placing big ball in the shaft first then spring then detent housing . No wonder why it didn't work. Now I know what goes first.Thank you! 👍
@trevorstevens3469
5 ай бұрын
I can’t find any adjusting nut. Where is it please?
@jimrumsey7781
Жыл бұрын
Thank you, I’ll try it. Been messing around with this all day
@tsugazi
4 жыл бұрын
Hi, Can you please post where you bought the spring and ball bearings? I believe my spring isn't quite what it should be. Thanks!
@savinggraces
Жыл бұрын
Hello: I need those kind of ball bearings. Let me know where I can get them. Mine on the MTD log splitter got lost only one is left. Thanks.
@jimyoungquist1687
Жыл бұрын
Do you have a link for the energy detent repair/rebuild parts?
@savinggraces
Жыл бұрын
MTD LLC, Cleveland, OH. may be the place to buy parts for these log splitters. Search for that company, those who are looking for parts. They have lists of machines and part lists.
@trevorstevens3469
5 ай бұрын
I know that you did this vid 8 years ago and not sure if you’re still on the air but I reinstalled my ball bearings etc but detent doesn’t quite hold (almost). Is there an adjustment available?
@thisisyourcaptainspeaking2259
4 жыл бұрын
Wow, those log holders (both!) sure are bent up, try not to split wood so it hangs up under them and not only will they not be bent but you won't have to wrestle the wood wedged under the holders. I recommend grease or heavy gear oil as lubricant opposed to WD-40, which will evaporate away in no time.
@donhunt8443
Жыл бұрын
Is there an adjustment on the detent spring; my engine dies on detent.
@crxess
8 ай бұрын
So, why did you not snow any Bearings when the Back Cap was removed? Is like you were starting from the middle of the Repair... Energy no longer list the Bearings, instead opting to sell an upgraded detent assembly at about $60.
@truwebs
5 жыл бұрын
Thanks for the great video? Where do we get the bearings?
@hlanceboyd
4 жыл бұрын
I lost 1 of the 4 small bearing/balls. Where can I get these and size? are you sure this is an energy valve, and not an MTD valve? also, there is an O-ring that is held into place by the detent cover when it is screwed down. I think I have a leak coming from that O-Ring. I have a cub-cadet log splitter with a valve from MTDparts.com model 718-04706P. any help on the O-ring and ball replacement would be appreciated. MTD doesn't have a re-build kit like EnergyMfg.com does.
@hlanceboyd
4 жыл бұрын
also, your comment on the "seal" (not being a great seal) is not really a seal at all. this is the flat area of the detent cover that holds an O-ring in place, which makes the seal I believe.
@salf4366
6 жыл бұрын
where can I buy these parts?????
@savinggraces
Жыл бұрын
It is a Yard Machines 25 ton...will not work without these bearings, Can grease be a help to hold the bearings in assembly.
@darrellwofford3297
Жыл бұрын
would you know what size the large bearing is I lost mine and don't know what size it is
@MsSoccerbabe2
3 жыл бұрын
did the same to mine today works perfect
@nighthawk8834
Жыл бұрын
Do you have to drain the hydraulic fluid out of it first?
@philliphall5198
7 ай бұрын
No
@rottiejakeluke
3 жыл бұрын
I appreciated the video but what was the issue which caused you to preform this rework? Thanks
@brianrizzi6321
3 жыл бұрын
Yes I’m wondering that too. May retract works but then it sticks and won’t let go. Was this your problem?
@mwentworth1
2 жыл бұрын
@@brianrizzi6321 same issue I’m having. Did you find a solution?
@philliphall5198
7 ай бұрын
Balls ware out and egg shaped Then it sticks Just replace the small balls and usually your ok
Пікірлер: 36