Ford Mondeo Mk4, front wheel (Gen 2) bearing replacement in car, using the special tool. Front bearing replacement without removing the steering knuckle.
I am in the middle of it, but your film helped me a lot. I was little surprised there is no circlip anywhere
@patriklabic8467
3 ай бұрын
Hi, thank you very much for nice manual :), in about hour i go to do it on MK4 , wheelhub is still sleep in freezer, everything is prepared for this job. :) DIY 4ever :D
@bignasty3274
7 ай бұрын
You must remember to oil the forcing bolt as it preserves the threads.
@Vanadeo
Ай бұрын
Important, especially on them wicked spring compressors.. I hate those.
@TeachDIY
25 күн бұрын
@Vanadeo Completely right. I bought a pedestal hydraulic one from amazon for about £95. Never using those stupid bolts again.
@Formastic
2 жыл бұрын
You saved me a lot of research, especially regarding the tool required. Thanks.
@TeachDIY
2 жыл бұрын
I am glad it helped. All the best.
@SparkyVuggs
Жыл бұрын
Brilliant video which showed me exactly how to use the tools I've just bought.
@daviddalziel884
Жыл бұрын
Great video ! Really helped so I could have an idea to tell the garage what I thought the problem/noise would be . Unfortunately the discs were so worn they had to be replaced along with the pads so that the bearing ( just o/s) could be fitted . Thanks again for posting.
@edbrandt8972
Жыл бұрын
Great video. And good job of showing the new hub going into the knuckle.
@vincentyerkess7230
Жыл бұрын
Great video!!! I'm about to do this job as soon as the removal/fitting tool arrives...thanks for the upload :)
@tomek860
9 ай бұрын
If you hear the bearing while ratating wheel by hand, they are worn as hell. Normally you hear them when wheel sre spinnig under the full load of a car. Nicely done 👍
@MadTitanGamer
Жыл бұрын
Great video thanks for sharing
@fujie-web
11 ай бұрын
Good job Guy ;oP Is it possible to send the scan of the user manual of the tool used (the one presented in the video) in order to clearly see the installation according to the extraction or the insertion? Thanks in advance.
@WelshChapman
8 ай бұрын
Thank you for sharing
@TeachDIY
6 ай бұрын
Thanks for watching!
@gilleskirch7403
Жыл бұрын
Thank you a lot for the video! Can you tell me/us the name of that special tool btw where you found it? Thank you!
@nevc3968
Жыл бұрын
Hi great video, where did you get the bearing tool from? 👍
@chriswill2136
Жыл бұрын
i just snapped that bolt in the centre spline how do i get it out what size is it,doing different job ,can i drive without washer temporary
@mrconta
Жыл бұрын
Where can i buy these pressing tool kit?
@thisistheway1766
Жыл бұрын
what size are the tools? is it 82mm
@krisu918
2 жыл бұрын
Hi, you should replace that tie rod end if spinning like that.
@TeachDIY
2 жыл бұрын
I have no problem with play, vibration or issues during cornering. Tie rod ends are just a ball and socket, sometimes they spin like that without needing replacing.
@krisu918
2 жыл бұрын
@@TeachDIY Hi. If it is loose like that its mean it is on its last legs. Regards :)
@krisu918
2 жыл бұрын
@@TeachDIY thanks for video 👍
@kristian3a
Ай бұрын
7:51 what are you doing here, after you removed the bolt, and before you move the drive shaft?
@TeachDIY
25 күн бұрын
I am using an air hammer to unseat the drive shaft from the wheel hub.
@burteaadicostinel1124
Жыл бұрын
what size is the extractor in the red box? I would buy an extractor and it is small, I will have to send it back The one I bought is 72. I think I have to buy 85. I have a 2006 Ford C-max
@ollyk22
14 күн бұрын
Which toolset do you use to remove/replace the bearing?
@TeachDIY
12 күн бұрын
Gen 2, wheel bearing tool. From memory, I think it's an 82mm, but check yourself before you buy.
@jpadilla0515
6 ай бұрын
Hello, what is the name of that tool you're using? In the red box?
@TeachDIY
25 күн бұрын
Gen2 wheel hub tool. It comes in different sizes, from memory this one is 82mm, but it has been a while.
@TheDutyPaid
6 ай бұрын
That is that lift you have there?
@TeachDIY
6 ай бұрын
That's a portable pivot car lift www.sealey.co.uk/product/5637706758/1500kg-portable-pivot-car-lift you can buy them from a few different manufacturers.
Жыл бұрын
mk4 front 82mm✌
@kevinthacker8349
8 ай бұрын
Thank you just the information I was looking for
@MrDean646
2 жыл бұрын
Can you tell me where you got the tool from
@TeachDIY
2 жыл бұрын
I got mine from ebay www.ebay.co.uk/itm/284354587608
@ANDY-we7mr
Жыл бұрын
What size,is that tool 78mm
@ANDY-we7mr
Жыл бұрын
HI MATE I HAVE A FORD FOCUS MK3 64 PLATE I HAVE SEEN THEM BEARING PULLER ON EBAY IT SAYS I NEED A 78MM PULLER IS THAT RIGHT IS YOUR 78MM CHEERS
@374psalm
Ай бұрын
How much would this cost at a garage? Rough price?
@TeachDIY
25 күн бұрын
Anything between £170 to £300. I spent £45 on the hub and £55 on the tool. Since then, I have used the tool once more, so the second time, I only spent about £45 for the bearing. You can get cheaper bearings, but I am not sure I would trust them.
@374psalm
24 күн бұрын
@@TeachDIY thanks...aye it cost me £150 ...supplied and fitted
@Assarkask
3 ай бұрын
Hi is it the same procedure for mk3?
@Vanadeo
Ай бұрын
Similar I imagine.. They're pretty much same concept on most cars..
Пікірлер: 46