Notes: Cylinder with piston down on compression stroke. 15/16 socket. 1/4 X 28 X 4". There is supposed to be a little part in the end of the puller, it was missing. Any questions feel free to comment and subscribe!
@mre1984
11 ай бұрын
The best info you shared that may be overlooked a lot is the 1/4x28x4” bolts. Thanks for that!
@stevensapyak7971
5 ай бұрын
1.21.24. The 1/4 x 28 x 4” bolts will work⚠️ however the threads are actually Metric. 6mm x 1.0 x 70, 80, or 90mm depending upon what puller is used.
@RatBasterd
2 жыл бұрын
Thanks for posting this! You confirmed 2 critical things for me: I have the right size socket, and the wrong puller.
@ishmaelwilliams304
8 ай бұрын
Wow THANK YOU!! finally I found a video that may help me! 4” bolts and leave the original bolt in and press against it!! HOLLY COW I didn’t think of that one I just switched my pulley! I’m going back for the $20 pulley and do it as you just showed me!!
@Dutchtheyooper
8 ай бұрын
If you use the long pushrod you can take the bolt out.
@debbiewatson7022
2 жыл бұрын
Thank You, you were more informative, & showed more. others talked more & showed less of actually what they were doing. Thanks again
@oliverrojas3185
2 жыл бұрын
I did not overtighten the puller bolts after watching you ease out the harmonic balancer. Thanks, your instructions are hellpful.
@sadeshine69
2 жыл бұрын
Thank you I was able to change it out and put a new one on I'm back rolling.. You Rock!
@doodlegassum6959
2 жыл бұрын
Really good info, especially the bolt sizes. Thankyou
@doodlegassum6959
2 жыл бұрын
If any ozzies are wondering, this info is good for your vy commodore 3.8 as well
@iansmith5052
2 жыл бұрын
Thanks man I got it removed so far
@liamtroesh35
Жыл бұрын
Doorman pick a nut at advanced is a lifesaver- they have 1/4-28 x 3” (luckily in stock) and that with some 1/4” washers did the trick
@miomine3527
Жыл бұрын
I bet that's the harbor freight puller.. The same thing is happening to me the bolt on the puller is screwing into the threads where the crankshaft bolt goes..so I'm like wait something is not right here..and here's your video certifying my suspicion..thank you for the vid...👍
@Dutchtheyooper
Жыл бұрын
It is actually the loaner tool from Advance Auto. (Probably made in China)
@marcusharrell9608
Жыл бұрын
@@Dutchtheyooper hey did the loaner tool come with the screws you used to thread in?
@Dutchtheyooper
Жыл бұрын
@@marcusharrell9608 It did not come with the correct bolts. You can get the correct bolts at Tractor Supply, Menards and maybe Ace not sure about Lowes and Home Depot
@marcusharrell9608
Жыл бұрын
@@Dutchtheyooper ok thanks
@danieljay247
Жыл бұрын
Thank you
@LanceNeves
4 ай бұрын
Good video! I would add in text if possible if using rope trick it has to be on the compression stroke because if it is on the exhaust stroke the rope will bend the exhaust valve.
@Dutchtheyooper
4 ай бұрын
Thanks, I added it!
@blakefarlow
8 ай бұрын
hey mate whats the size of the bolts you use with the puller tool
@bugstomperkiwi
18 күн бұрын
Nothing in there to thread the three bolts into.
@Dutchtheyooper
18 күн бұрын
Are you sure you have the correct size bolts? Maybe they threads in the are filled with grime?
@adventureoflinkmk2
5 ай бұрын
How newer is newer? Because i got a 2001 buick park avenue that i need a new crank sensor put on. Do i follow the 76 degrees or the 114 degrees Also what does 1098 mean
@Dutchtheyooper
5 ай бұрын
111 + 76 degrees. New bolt is recommended since it is a stretch bolt but I have never had a problem reusing them.
@adventureoflinkmk2
5 ай бұрын
@@Dutchtheyooper Roger that. Good to know thanks. Also: I was told that you need to secure the flex wheel before torquing it. Is that true.. given I saw TRQ I think it is, use the special tool bolts and wedge a pry bar in there
@Dutchtheyooper
5 ай бұрын
@@adventureoflinkmk2 I usually put vice grips on the flex plate
@adventureoflinkmk2
5 ай бұрын
@@Dutchtheyooper and it's easy access to get to without having to remove the transmission or the starter right
@Dutchtheyooper
5 ай бұрын
@@adventureoflinkmk2 No, you would have pull down the starter. I have also removed a spark plug and stuffed rope in the cylinder but there is a possibility of damaging something, never had a problem with that method either.
@skids4days42
Жыл бұрын
What engine is that out of
@Dutchtheyooper
Жыл бұрын
Not sure, it was not original to the car
@nodayatthebeach
2 жыл бұрын
Fought it, Won !
@Dutchtheyooper
2 жыл бұрын
Yes, it's different in a car. I did it on an engine out of the car for ease of doing the video. Thanks!
@johnisaacs8909
2 жыл бұрын
The right bolts to use are 6mm x 1.0 thread pitch
@stevensapyak7971
2 жыл бұрын
3.14.22. You are correct they are actually metric threads. M6 X 1.0 thread pitch X 70/80 or 90mm long, depending on what puller you use. Also use hardened hex or Allen bolts. You may need hardened washers too. Oh and use a propane torch to heat up the 24mm crankshaft bolt holding the harmonic balancer on! Just a minute or two, It helps to break the Loctite they use on the bolt.
@mmorgz6622
Жыл бұрын
can confirm. im working on a 3.8 ecotec from a VS commadore(AUS). picked up some of these M6x1.0 bolts at 100mm long from bunnings. fit perfect. thankyou johnisaacs
Пікірлер: 42