Hi all & Welcome to my Channel :) On this Video i Show you on my PS3 test board, how you can Repair your brocken Fan Connector. Have Fun, Thumbs Up and and dont forget to Subscribe :) PEACE
NSC thanks a lot, I did this on a slim 2003B. The third contact from the left in this model cannot be seen (the third "dot" above the 2 bottom dots is not there) but you can scratch to find it, just follow the rough diagonal direction from the video. Of course you must be careful you don't scratch too much and join the ground. I kept scratching, soldering and testing with a multimeter until pin 3 wasnt ground and now the fan is all working. Thanks again NSC.
@NSC-Modz
3 жыл бұрын
Nice job bro. You always welcome ;)
@mikefahey1839
2 жыл бұрын
I didnt see the hole on My 2001a either. Thanks for the info!
@ecv80
8 ай бұрын
I didn't see mine either although I don't know the model. Thanks for the info too.
@MrNemay
8 жыл бұрын
Thank you !! I was stuck in the 8002f1f9 loop and I lost all hopes to have my PS3 working again.... Now it's back with CFW 4.75 !! Gratitude ..
@NSC-Modz
8 жыл бұрын
+Ne May Cool, im happy for you, really :)
@pixelgaming4603
8 жыл бұрын
+UltraNSC I have a cechL03 model ps3 and i hope you will reply to this, that connector your repairing looks the same as my ps3 power supply connector, I was replacing my blu ray drive that was broken and i had to remove my power supply because the connector is on the back so I ejected the power supply connector until the whole thing ripped off, i tried EVERY video on youtube but i cant find any I tried asking everyone for help but they wont even bother to reply, so please show us a tutorial.
@isaak3168
5 жыл бұрын
@@NSC-Modz can you please help me I took apart my ps3 and soldered a can wires to the fan connector and now when I have it soldered it turns on and turns off right away I have to unplug and plug back to turn back on then it shuts off right away I removed the other fan connector and it's still doing this.
@INSTXNT-_-KXRM3
3 жыл бұрын
Halt sowas ist wirklich Hilfreich für die Leute die diesen Connector zerstört haben.Ich habe ohne zu wissen schon am Anfang gewusst das man dass Kabel vom Lüfter nicht einfach rausziehen darf.Falls ich das nicht gewusst hätte ,hätte ich dein Video sowieso geschaut weil es immer Tipps gibt
@NSC-Modz
3 жыл бұрын
hehe, das kannst du laut sagen :)
@ecv80
8 ай бұрын
Thank you so much for the thorough explanation. The quick fast motion intro was a good glimpse but you made the whole video interesting. I watched it entirely even tho I normally don't do videos longer than 15 min. My fan was apparently working intermittently since the last time I opened my console. I checked and the connector was a little loose on the board. I put some solder on the three front wires but it didn't help much because apparently the side contacts were already ripped. I pulled the cable out carelessly and the connector came right off peeling off the tracks underneath. I didnt see any contacts to solder onto anymore so I thought I would just solder the fan wires directly on the back side. But I will now try the method on your video. I don't have high hopes because I can't really see the middle hole contact for the right pin on the board anymore. But at this point I'm just calling it a loss and it will be the perfect excuse to get a newer PS model. Only if they can be hacked to have Movian and RetroArch and things like that. Otherwise I'll get another ps3.
@NSC-Modz
8 ай бұрын
You welcome. Yeah, sometimes vídeos needs to be longer, otherwise you can't explain all. Wish you all the best, and just come back if you need something. Merry Christmas to you and your family 🤗
@pancanugraha1028
9 жыл бұрын
greeting mr NSC, i had problem a broken ps3 slim fan connector like your video, and i had follow your tutoriol video it's work ! ! ! thanks very much for your kindness but now , the fan is spinning faster like a jumbo bombing jet now how i must to do in order the fan spinning like early ? *sorry if my english is so badddd
@strikehosting2501
7 жыл бұрын
I know this is an old comment, but I figured I should post why this happens. So there's a gray wire that connects to the first pin, it's what controls the fan speed. In this video he's scraping a lot of the board and then attaches a wire to it to make the connection bigger. This may be improperly soldered and/or not connected. IT could also be an issue with your heatsinks not aligning properly or the thermal paste may not be enough.
@NSC-Modz
4 жыл бұрын
Just saw this post right now, stupid messages sometimes are not showed up. The IHS are the problem, you need to remove them and apply new thermal paste inside the IHS
@tealblueish7033
4 жыл бұрын
*WZUP!! NSC MOdz i really tried and almost worked!! but the fan will shut off at start up i guess the connection was weak, anyways that hair thin cable is a bitch So i opted to solder the 3 cables on the bottom and put some insulator tape and connected the fan and VOILA!!! it's working AGAIN!! so PEOPLE if for some reason u can't reattach the connector y'all can try with the 3 cables good luck*
@kmax7521
3 жыл бұрын
What you mean by 3 cables though? You talking about just extending the 3 cable fans and soldering them directly from the back of the pcb fan connector right?
@justingirard4156
7 жыл бұрын
Love how he got the sound from "short circuit"
@El_Bodhisattva
6 жыл бұрын
you save my ps3 bro! thanks a lot ! great job and tutorial!
@NSC-Modz
6 жыл бұрын
You Welcome :)
@masterpanos1990
3 жыл бұрын
Hey man. I have the same issue as well but I cant see the little hole that you put the cable on the motherboard. I have scratched the surface a bit in order to expose it if its there, but I didnt find it and Im worried to further proceed. Do you know if a DYN-001 motherboard has that hole?
@jhannes14
9 жыл бұрын
Is ne schöne Arbeit ^^ hatte das gleiche Problem bei ner FAT CECHL04 aber mit dem Netzteilstecker :/ halt für ne halbe h gehalten dann war er wieder ab aber jetz geht wieder ^^ NSC=Best KZitemr xD
@NSC-Modz
9 жыл бұрын
+Era_MoDDz Vielen Dank :)
@Daniel-dl6fp
6 жыл бұрын
Omg thankyou so much you saved me spending loads to get repaired I subscribed
@NSC-Modz
6 жыл бұрын
You welcome :)
@Mr_Freaky_Harish
Жыл бұрын
Bro plz help.....u have fan problem ripped?
@rick40171
3 жыл бұрын
God bless you saved my ps3 great tutorial and congratulations
@Anthony-qt8wv
2 жыл бұрын
Anthony 0 seconds ago If you just disconnect the fan from the assembly it is in, you don't have to unplug it from the motherboard. Keep the fan close to the board and tape it to the metal to keep it from getting crimped/cut. I just though of that and will be doing that on mine! It has plenty of wire to extend from it.
@NSC-Modz
2 жыл бұрын
Yeah, but not good to work around at all xD
@IDevvo1
9 жыл бұрын
Congrats for 7k now make more vids
@randydavis941
5 жыл бұрын
Ya, Another awesome video!! Really man thanks for being here for us!! Peace
@jeffbanfieldsflwr3537
Жыл бұрын
How can you not like this guy.
@NSC-Modz
Жыл бұрын
Ohhh Thank you soo much 🤗 You always welcome ✌️
@Jimmy.arriagada
Жыл бұрын
U saved me, i make my first mantention after 13 years and i broke the fan connector lmao
@NSC-Modz
Жыл бұрын
Hope you fixed it 😀
@jasonscalzo9597
3 жыл бұрын
My first time soldering and I’m having a hard time, I rage quit 😤 I will have to revisit it tomorrow and maybe get some help. I will get it done!
@NSC-Modz
3 жыл бұрын
Where you from? I could do it for you ;)
@syrusse8660
7 жыл бұрын
JUST WHAT I NEEDED, SUBBED
@NSC-Modz
7 жыл бұрын
THANK YOU :)
@DIS2RBER
Жыл бұрын
You, Sir are a life saver! Thank you for everything. :)
@NSC-Modz
Жыл бұрын
You always very welcome 🤗✌️🥰
@nicolasgaviria9839
8 жыл бұрын
you saved my ass once again, thank you from Puerto Rico!!!!!!!!!!
@NSC-Modz
8 жыл бұрын
I LOVE Puerto Rico! You always Welcome
@thomasnq
2 жыл бұрын
Exactly what I'm looking for. Thank you sir !!!
@NSC-Modz
2 жыл бұрын
You always welcome bro.
@viniciussa1986
9 ай бұрын
Eu também, mais tá difícil hein
@shanewasherebaby1
9 жыл бұрын
Right on! That is awesome NSC!
@xCarloson27
4 жыл бұрын
Thanks broo!! I fixed it thanks to you
@NSC-Modz
4 жыл бұрын
You welcome my friend ;)
@xCarloson27
4 жыл бұрын
NSC Modz Thanks :) hopefully someday a flasher like e3 will come out and we'll make money again doing what we like on ps4, It would be my dream since I could not get into ps3 scene years ago, I bought e3 flasher a few months ago and now I am doing rgh on xbox 360
@NSC-Modz
4 жыл бұрын
@@xCarloson27 Google: 👇 PS3 Exploit :)
@xCarloson27
4 жыл бұрын
NSC Modz Bro I dont like exploits... I love hardware 100%
@FLAME-FLICKE
9 жыл бұрын
hey NCS, good video. Please can I ask you something about an e3 flasher?
@BirdManNorth
4 жыл бұрын
My board does not seem to have that small line for the third contact.
@NSC-Modz
4 жыл бұрын
Maybe under there...
@BirdManNorth
4 жыл бұрын
NSC Modz thanks I’ll give it a look, it’s a newer model of the slim so hopefully it’s the same. There’s always the easy wire fix to the other side of the board as well. Thanks for the video man! Really easy to follow.
@NSC-Modz
4 жыл бұрын
@@BirdManNorth you welcome, don't forget to subscribe ;)
@MrGameX
9 жыл бұрын
Greetings from Romania Please can you make one video about how to flash xbox 360 with lt 3.0? I even watch your channel and i like your videos very much
@jurkovf2437
4 жыл бұрын
NSC are you still there? I need your help, because you are the best 😁
@mecorx
4 жыл бұрын
Hey NSC! Hope you're doing well. First of all, thanks so much for your tutorial. I tried your method, cleaned up the board according to your instructions (imgur.com/a/UGoCtoE), carefully made sure pin 2 and 3 did not touch (imgur.com/a/9xAhh7f). I soldered a small portion of cable from an old fan for pin 3. But, when I booted the unit up/did fan test the fan does not spin. Do you have any advice? Before I tried this proceidure the fan would spin 2-3 sec on startup. Thank you for your time! Edit: tested the fan in another ps3, it's still working! Edit2: My soldering iton runs at ~400c and I used a rosin flux pen (cleaned before trying to start the ps3), 63/37 solder. Edit3: Ahm, i tried soldering cables directly to the points on the back side to the header and now the fan works... A pity I wasn't good enough to do it your way!!!
@NSC-Modz
2 жыл бұрын
Omg just saw this comment right now 😅
@mecorx
2 жыл бұрын
@@NSC-Modz Hahaha. All good, my hack job is still working at least.
@rolferoswaldohermitanosanc2642
10 ай бұрын
Es necesario ponerle el cablecito? Digo pelar tantio hasta que el cobre de la placa se vea y soldar, sera que sirva?
@ronniesanchez9634
4 жыл бұрын
Hello men soy de chile ayer me paso lo que pusiste en tu video hoy hice la reparación me sirvió harto ya que tu video es largo y se ve claramente como repararlo gracias espero estés bien por tu hogar gracias
@NSC-Modz
4 жыл бұрын
Olá Amigo ;) Gracias
@kakoflips7795
2 жыл бұрын
Amigo yo igual soy de chile, y me pasó lo mismo hoy, te costó mucho hacerlo?, No entiendo mucho ingles 😔
@sjmak5500
9 жыл бұрын
my nigga nsc is baaaack!
@NSC-Modz
9 жыл бұрын
sj mak PEACE Bro. !
@jackrabbit2765
5 жыл бұрын
Hello Thanks for the video, I messed up the first pin, the pin you said not to solder together.. Is there another trace to the pin on the board.
@jasonmattison6734
7 жыл бұрын
I have A 2001a slim that the white 4 wire connector from the power supply to the mother board ripped off the motherboard. Are there solder points on the bottom side of the mother board I can connect wires to?
@TheInsaneHoster
7 жыл бұрын
How would u do this for the fat PS3 ? Because mine is broken on the fat
@sgdzgamer3576
9 жыл бұрын
nice video i had the same problem Whit mi slim. I solder 3 kabels on the other side of the motherbord but this way it stay original nice work man .....how can i connect you i have some problems whit mi ps3 i think you can help me fix it
@georgebraun5219
5 жыл бұрын
@UltraNSC will this work if my ps3 fan has some of the paint still on it? trying to scratch it if but afraid I will ruin the connector further. Also just to clarify I need: a razer or flat screwdriver, soldering equipment, some flux, and some ide cables, where would I get the cables? Also could I use alchohol (91 percent) instead of flussmitel cleaner?
@Stormynknight
9 жыл бұрын
its alive! Lol Nc make a video on replacing the bluray connector on a cok-001 board peace in the place to be.
@NSC-Modz
9 жыл бұрын
Stormynknight i dont know if i got that board here ^^
@carlangas4299
9 жыл бұрын
Hi! I have a ps2 fat and the connector of the start botton of the motherboard is broken and i cant turn on the console. Do you know another way to turn on the playstation 2 fat model? Please help!
@jeffj9213
2 жыл бұрын
Somehow I cannot solder on the 3 point on the board , no matter what I try. I got a magnifying glass that makes it really big to see what I solder but it doesnt matter. I did try it the first time and when the playstation turns on the fan starts for only 5 seconds and then turns off , then a minute later the playstation turns off because it gets hot. Im gonna try a last thing to solder the wires on the other side of the board but the right solder point is shitty af , the old solder doesnt want to get liquid....so its really hard to solder on something.... Maybe I just gonna buy another ps3 2nd hand since I can buy these for like 50 / 60 bucks .
@NSC-Modz
2 жыл бұрын
Yeah sometimes it's just better like that xD
@ozturkebrahem
10 ай бұрын
Just get a USB cord cut it and connect your fan to USB port in the front. You already there don't give up you can make it work
@viniciussa1986
9 ай бұрын
Ficou prefeito, parabéns 👏👏
@NSC-Modz
9 ай бұрын
Obrigado 😀
@viceith
3 жыл бұрын
thanks dude XD it worked for me S2
@NSC-Modz
3 жыл бұрын
You welcome :)
@user-ov9kt8te5r
9 жыл бұрын
Hi NSC and greeting forall your perfect work you r the BEST :) I really have aproblem to solid a wire from SBE to GND I Have a FAT Lady XD And i read the post you suggest to read but i have a lot GND point on board and dont know which one i solid with SBE . Thanks from IRAQ To you
@NSC-Modz
9 жыл бұрын
مصطفى سعد الشمري you can Chose any one GND Point :)
@user-ov9kt8te5r
9 жыл бұрын
Thanks i'll try . if i want to ask you many important questions where to post mine? skype or facebook
@NSC-Modz
9 жыл бұрын
i dont got Fakebook xD and Skype yes, but im not so often Online... You can add me on whatsapp or write me an eMail: UltraNSC@live.de
@user-ov9kt8te5r
9 жыл бұрын
Hi man i send you many posts to your email but no respond maybe somthing wrong?
@jet613
9 жыл бұрын
I like to sand it down and use a little flux :D
@ricardocosta3073
9 жыл бұрын
Nsc i know it has nothing to do with the post but can you tell me if its possible to downgrade a PS3 Slim 2504B Datecode 2B that minicheck says "Update data of version 3.56 or later can be installed on this system." ? Thanks in advance.
@xls4750
6 жыл бұрын
NSC can help me I replaced my ps3 thermal paste under the ihs and the fan still running loud in home screen and it overheats when playing call of duty
@ViniBreda90
Жыл бұрын
My ps3 had this exact same problem. After I fixed it the right pin is shorted to ground. Should this be happening? I don't see any physical shorts.
@NSC-Modz
Жыл бұрын
This kinda shorts are hard to see. You will need to check the fuses to...
@BlackenedGaming
7 жыл бұрын
How many watts is your soldering iron? I have one of 80 Watts. Will it serve me or is it too hot?
@NSC-Modz
7 жыл бұрын
Yes, sure it works... Watts has nothing to do about the iron Temperature... :)
@stillperspective488
7 жыл бұрын
Hast du ein Video wo alle Schritte (Downgrade mit Flasher, wiederzusammenbau, cfw, etc.) gezeigt werden? Ich habe gerade bei meiner ps3 Slim Motherboard JSD-001 den fanconnector wie bei dir zu sehen herausgerissen. Jetzt will ich das probieren und den Downgrade dann fortsetzen. Danke im Voraus für deine Videos!
@estefanimartinez4621
4 жыл бұрын
I burn the connector with a soldering gun Now ps3 turns off automatically what to do ?
@perchahz3159
9 жыл бұрын
Can u make a video on e3 linking. And can u still downgrade if you break your fan connecter
@Adam-rt7lp
3 жыл бұрын
@NSC Mods Is this the only way to repair the fan connector?
@NSC-Modz
3 жыл бұрын
Let's say, the right way.
@Adam-rt7lp
3 жыл бұрын
@@NSC-Modz OK thanks for the reply my man. The reason I asked is because I saw a ifixit guide which solder 3 points from the back of the motherboard to the fan connector. www.ifixit.com/Guide/Repairing+PlayStation+3+Slim+Ripped+of+Fan+Connector/11882
@calvinreese3961
9 жыл бұрын
hey ultra gilt die nummer von dir in der kanalinfo noch ? hab ein wichtiges anliegen
@elrolomonger2827
2 жыл бұрын
hi mate, have the same board jtp-001, but the wires of the fan where cut and fixed in a very bad way, so i proced to change the fan completly for testing purpose, the system starts but there is no video, it bip for disc tray, for changing resolution, to enter recovery, everything, but when power of it does not bip, but it gets of, the real problem is that it has no signal, so i think that it could be something in short, because of the fan cables but i dont know were...look for info in forums like eol, psx-place but nothing related... :(
@NSC-Modz
2 жыл бұрын
Hmmm smells like a sort bro...
@Pellum
7 жыл бұрын
Hey NSC..my ps3 slim no power no red light no anything.??Please Help Me NSC ♥
@mateusds8160
4 жыл бұрын
This happened with me , but my motherbord is KTE-001 PS3 Slim 3k someone can help me ?
@NSC-Modz
4 жыл бұрын
It's the same way for this board to :)
@excitedaboutlearning1639
3 жыл бұрын
NSCMod, my PS3 Slim 3003A has the following issue: it struggles to boot. Sometimes, when it boots, it works for hours and other times it freezes. I've changed the thermal paste, swapped the power supply and changed the HDD, but none of this has fixed this issue. I got the system to constantly boot by taking out the HDD and putting it back. That somehow does the trick. I think the system also boots if I take out the power supply abd put it back in. Basically, the system boots after you've removed a component and put it back. What could be causing this?
@NSC-Modz
3 жыл бұрын
Hello You sure your ps3 is not overheating? Did you saw my video about the Syscon Connection Reader?
@excitedaboutlearning1639
3 жыл бұрын
@@NSC-Modz It's not overheating. I never get an overheating warning,and the struggle is only "visible" while booting. For context, it's a UK model that I run through an electricity converter. It started having symptoms a month after I got it. The converter is not at fault, because it does the same thing with a different cable. However, it could've caused the issue to emerge in the first place.
@strikehosting2501
7 жыл бұрын
Hey NSC I love all of your videos, they've helped me a million times and this is the MOTHA FUCKING PLACE TO BE but unfortunately I soldered all the wires and now when I turn on the ps3, the fan spins for a few seconds and then stops. Do you know if this is caused by something specific? I have a 2501a so your other video which shows other locations to solder aren't on my board.
@complexgaming1809
9 жыл бұрын
hi i love your videos do you think you know how to get out of red screen for death im stuck on 3.55 rogero downgrader but it will never let me got to 3.55 cfw it only works in 3.55 rogero download everytime i try go to a 3.55 cfw it stops ar 44% and goes to 100% really fast and gives me a red screen of death i thought you'll be the only smart one to know but any way
@TheRealMikeMichaels
3 жыл бұрын
Can I solder the wires directly to the motherboard? The connector I have has the silver pin scratched so I am not sure if it will work.
@NSC-Modz
3 жыл бұрын
Hmm, if you not sure, you better don't touch it... or you gonna risk a short
@TheRealMikeMichaels
3 жыл бұрын
@@NSC-Modz thanks, I just rather join the fan cable and one usb cable and taped it up with electrical tape instead of soldering it.
@neets8360
4 жыл бұрын
Hello! I would like to do this but don't have edl wire, is there other wire I can use instead? Thanks!
@NSC-Modz
4 жыл бұрын
Hello do you have soldering skills?
@MiXzMoDz
9 жыл бұрын
UltraNSC Ehm hast du FB? Oder so habe da mal ne Frage.
@will_mcdermott
9 ай бұрын
Dang I just realized my PS3 was manufactured in January 2007 and the void label has never been removed but now I gotta take it off
@NSC-Modz
9 ай бұрын
That's life 😆
@pasigstreetstyle3390
2 жыл бұрын
what is that connect that you put a little wire ?
@NSC-Modz
2 жыл бұрын
You mean Flux? Or the thin cable?
@fuckmask4965
2 жыл бұрын
26:15 I'm stacked here.. do i have to use the cable or can i use any piece of copper?
@NSC-Modz
2 жыл бұрын
You can use all, witch gonna give you a great contact.
@fuckmask4965
2 жыл бұрын
@@NSC-Modz Okay Thank You, i'll try It☺️
@fuckmask4965
2 жыл бұрын
@@NSC-Modz Last thing, what do u put in 22:15? "Add some flags?" I don't understand english rlly good so.. i didn't know what It Is😅
@NSC-Modz
2 жыл бұрын
@@fuckmask4965 flux* this is for better soldering...
@prankmebro6616
9 жыл бұрын
Can you please make a video how to open PS3 slim ?
@feralnoremorse6891
Жыл бұрын
I don't have tools for it either I rather just go by the motherboard or whatever switch it
@gabrielmanarte6809
24 күн бұрын
Is there any specific solder wire? I bought a general purpose wire and this thing doesn’t stick to the scratches I have done
@gabrielmanarte6809
24 күн бұрын
I guess I shouldn’t have bought lead free wires
@NSC-Modz
24 күн бұрын
@gabrielmanarte6809 you can use flux, this will help so much.
@gabrielmanarte6809
21 күн бұрын
@@NSC-Modz it worked, I bought some proper solder wire and the flux. I did on a slim version so the power for the third pin wasn’t on the same spot as you mentioned. So I did the wire option you gave us. Thank you, keep on the good work.
@NSC-Modz
21 күн бұрын
@@gabrielmanarte6809 yeah, it conforms the model... you did a great job and you always welcome bro. ✌️
@gabrielmanarte6809
20 күн бұрын
I am thinking of changing the original fan for a noctua model nf-b9 redux 1600 3pin (not pwm, which would be 4 pin conector) it’s size from what I have been measuring would fit perfectly on ps3 slim models. But I have two concerns. 1 - would be a bad idea since there Amperage difference is quite large? 2 - would that bring better overall temperature to the console? When I mean overall, I wouldn’t only register the temps of the cpu and gpu. But measuring also other spots like power supply, Bluray driver, etc…
@smoodee8167
4 жыл бұрын
I cut the gray Wireless how I can fixed
@feralnoremorse6891
Жыл бұрын
I don't have tools for it either. I rather just Buy it i need to know where they sell it at
@LL-ck4ei
Жыл бұрын
Damn we are all here 4 the same
@NSC-Modz
Жыл бұрын
Yeah 😆
@LL-ck4ei
Жыл бұрын
@@NSC-Modz the worst part its not working after soldering it, it runs when I turn on the console but no luck after that
@NSC-Modz
Жыл бұрын
So there is a contact missing somewhere or shorten
@law_sensei
7 жыл бұрын
its for ps3 slim? can you tell me how can do this in a ps3 slim? i fuckup the fan connector...........................................
@NSC-Modz
7 жыл бұрын
It's also for the slim
@law_sensei
7 жыл бұрын
i do the same, but it seems doesnt have energy, wont work.....
@biteofbytes
8 жыл бұрын
Reference to Gigi d'Agostino - Super?
@alexanderpfeifer3598
9 жыл бұрын
Bei mir ist die Buchse von Flachbandkabel welche von dem Laufwerk kommt abgebrochen, bei dem Versuch die Ps3 Downzugraden. Was soll ich tun die Ps3 wirft die Cd nicht aus und liest sie auch nicht. Kennst du einen guten Reparatur Service?
@NSC-Modz
9 жыл бұрын
Alexander Pfeifer Ja, mich xD Ansonsten schau dir dann an: kzitem.info/news/bejne/0Y2cp56ZfZyidKw
@alexanderpfeifer3598
9 жыл бұрын
Bei mir ist aber ein Pin abgebrochen. Wie viel kostet die Reparatur + das Flachbandkabel bei dir? ( Das Kabel ist irgendwie nicht so breit wie in deinem anderen Video)
@NSC-Modz
9 жыл бұрын
Dann hast du ein H, L, oder K Modell, welches Modell ist es denn ganz genau? CECH - ( ? )
@alexanderpfeifer3598
9 жыл бұрын
CechL04
@NSC-Modz
9 жыл бұрын
ich denk wir haben bereits geschrieben :)
@BrazilMentionedHueHue
3 жыл бұрын
RIP Flux syringe
@NSC-Modz
3 жыл бұрын
Yep, i got thousands 😅
@headhunter34444
7 жыл бұрын
Is this à good fix for me kinda problem?? Me fan is going on on The boot up but stops in About 2 seconds but me ps3 stays on. its kinda broken. In dutch ( het zit los )
@NSC-Modz
7 жыл бұрын
No, you have an other Problem
@headhunter34444
7 жыл бұрын
UltraNSC i fixt iT with u tutor but iTS fine XD And i downgraded me ps3
@NSC-Modz
7 жыл бұрын
Ok Nice to know :)
@daffaarkana
5 жыл бұрын
Can you help me how to fix fan conetor on ps3 slim cech 3000
@NSC-Modz
5 жыл бұрын
It's the same way like here
@kmax7521
3 жыл бұрын
Anyone know why we must make new contacts. Why can't we just solder it back with the same contacts?
@NSC-Modz
3 жыл бұрын
Because the contact line was destroyed... so you need new contact...
@kmax7521
3 жыл бұрын
@@NSC-Modz ok. Let me ask you 2 more questions if you don't mind. 1. Can we just solder the tips of the wires to the contacts on the underside of the motherboard? 2. In terms of soldering skills, On a scale of 1 to 10 how difficult is it to make new contacts and solder the connector back to the motherboard. Thanks I might buy a Soldering station and get practicing, else i will have to pay someone to do it.
@NSC-Modz
3 жыл бұрын
@@kmax7521 Ok, for the first question, yes it's possible but i prefer to do it like it should be. And for the second question: hmm it's hard to say, if you are skilled than its easy, if not it's hard...
@NextGenModder96NGU
9 жыл бұрын
How to fix Broken Xbox360 Fan Connector?
@Ahmed-wp2rq
8 жыл бұрын
Could You Connect the fan to a power plug and power it or do is have to Be Soldered to The Board?
@NSC-Modz
8 жыл бұрын
+EaZy yes u can... but if u sold it on 12volts then the fan will turn to fast.
@matias3924
4 жыл бұрын
can i do this without flux?
@NSC-Modz
4 жыл бұрын
Yes, if you are skilled like me then yes, soldering wire has also flux.
@TheAmc1998
Жыл бұрын
How much to replace mine I just broke before watching this video? 😂
@NSC-Modz
Жыл бұрын
Oh shit xD you got no repair shop somewhere?
@TheAmc1998
Жыл бұрын
I’ll have to check it out might just buy another one cheap and swap motherboards. I feel like a total failure 💀
@NSC-Modz
Жыл бұрын
@@TheAmc1998 all cool, shit happens bro.
@Randomositaaaay
5 жыл бұрын
Self note at Minute 37
@Randomositaaaay
5 жыл бұрын
38:30
@NSC-Modz
5 жыл бұрын
?
@mrguapirriss97
5 жыл бұрын
PS3 slim ?
@NSC-Modz
5 жыл бұрын
Yes, it was the Slim, but it's the same also for the PS3 Fat and PS4
@yamatonokamoto955
9 жыл бұрын
Weisst du, wie man diesen Hässlichen piep ton beim an und abschalten der ps3 konsolen entfernen kann?
@NSC-Modz
9 жыл бұрын
Yamaton Okamoto Sicher weiß ich das ^^
@yamatonokamoto955
9 жыл бұрын
UltraNSC 😀 Geil
@phoenix_force_9867
8 жыл бұрын
OMG the beginning to Short Circuit!!!!
@NSC-Modz
8 жыл бұрын
+Ira Brown You know the Movie? xD The most dosent ^^
@phoenix_force_9867
8 жыл бұрын
+UltraNSC I used to watch it on VHS till the tape wouldn't work anymore!!!
@NSC-Modz
8 жыл бұрын
xD but you find it everywhere to download it ^^
@nik193er8
8 жыл бұрын
@B9NE
3 жыл бұрын
Clean your soldering iron tips dude!!
@NSC-Modz
3 жыл бұрын
No panic on titanic, all cool 😎
@bze5450
9 жыл бұрын
Wo wohnst du? Will ps3 jailbreaken
@NSC-Modz
9 жыл бұрын
akaMrxsOG ´Gibt´s doc hgenug anbieter xD bin aus dem Raum Stuttgart / Calw
@bze5450
9 жыл бұрын
Schade wohne neben Ulm ja du hast proof usw und bist bestimmt sicher
@NSC-Modz
9 жыл бұрын
Sicherer gibt´s kaum jemand anders, aber Ulm ist nicht weit von mir :) Max 80Km? Liebe Grüße
@bze5450
9 жыл бұрын
Ich finde leider niemand :( kennst du da welche wenn ja sag mir Bescheid danke dir :)
@NSC-Modz
9 жыл бұрын
ich könnts dir ja machen, nur nicht umsonst xD
@paramdhiman9363
5 ай бұрын
motherboard prints were fine you ruined so many good prints It seems like you are learning on the job 😂😂😂🤣🤣🤣
@NSC-Modz
5 ай бұрын
What are you taking about? 😂😂😂🤣🤣🤣😂🤣🤣
@prankmebro6616
9 жыл бұрын
It's broken, not Brocken
@NSC-Modz
9 жыл бұрын
Prank me BRO in German it´s Brocken xD
@prankmebro6616
9 жыл бұрын
But this is English, right
@NSC-Modz
9 жыл бұрын
yeah, Thank you :)
@moddingservice4540
9 жыл бұрын
UltraNSC hello UltraNSC on my ps3 slim my connector for the power supply broke off the mother bored is there any way that can be fix by hard wireing it to the mother bored or could u make a video thank you :)))))
@NSC-Modz
9 жыл бұрын
Make me some Pics and ill take a look
@ThePremiumlike
9 жыл бұрын
mach mal ein deutsches downgrade video
@Stormynknight
9 жыл бұрын
Nc any fat PS3 model will be just fine all that matters is you showing how to replace the bluray ribbon connector on the motherboard not daughter excuse my English it's not the best but fuck it I try lol
@NSC-Modz
9 жыл бұрын
Stormynknight yeah man, NO TRY > NO FLY xDThe Bluray connector i have already showed on an other Video, but maybe ill do a Video how to sold the whole Thing out and Replace it to a new one :)Have a nice time :)
@aaronveneruso2214
8 жыл бұрын
Hey man, great video as always!!! can I ask for your help? My ps4 has the broken connector of the drive data flat cable.. it is fully working but the white plastic on top is broken and the cable doesn't stay in position.. I asked in many repair stores but they can't do it :( since you are a brilliant guy I'll ask to you... here's a pic of the connector. thanks in advance!! s12.postimg.org/th2zj6g1p/IMG_20161004_160543.jpg
@NSC-Modz
8 жыл бұрын
Hello Try it to fix it like this: kzitem.info/news/bejne/0Y2cp56ZfZyidKw
@aaronveneruso2214
8 жыл бұрын
Hello :) thanks! i watched it but it is not 100% helpful because the connector is different (doesn't have the black clip), but, thanks to that video i can try to glue something on it to simulate the broken upper side of the connector. :) you are very very very awesome, i don't know how to repay you :D
@NSC-Modz
8 жыл бұрын
Np :) just take care with the glue, you better just try without glue :)
@aaronveneruso2214
8 жыл бұрын
Yeh I know that the glue may melt with the heat and even worse make a mess with the contacts, so i'll try to glue a support on the metal shield far away from the connector :D Then I'll try to cut a hole for the fan, since it's a day one model, so i don't care if it breaks :D
@stillperspective488
7 жыл бұрын
Ich brauche dringend Hilfe!!!
@amineshow1009
7 жыл бұрын
can you plzz hlep me my ps3 slim broke the same connector for the fan can you fix mine i will pay you $40
@nianticinc6242
7 жыл бұрын
steven albines I wanna sell mine for 50$ kik me wrlz
@MrGameX
9 жыл бұрын
Greetings from Romania Please can you make one video about how to flash xbox 360 with lt 3.0? I even watch your channel and i like your videos very much
Пікірлер: 228