Thanks, need to do my bearings on short notice and "morgan's tool" is both ridiculously expensive and won't make it here in time. This is perfect!
@andykerr9545
9 жыл бұрын
Thanks for Info mate-no need to buy a special tool thati will hardly ever need ......your ideas use stuff most mechanically minded people may already have in their workshops
@sidecarbod1441
7 жыл бұрын
Its worth warming up the swingarm with a blow torch so that it expands, the bearings will move with less force. It is also worth warming up the swingarm when fitting the new bearings because there less change of galling up the aluminium.
@ow-my-achilles1106
4 жыл бұрын
I've heard guys freeze the bearings for a few hours, so they microscopically shrink making them easier to fit. Safer than heating the swing arm and getting an ouchie..
@Revy8
7 жыл бұрын
thanks for showing how everything sits inside. that was what I was most curious about before starting the job, i wanted to have a clear understanding of what needed to come out in what order. it was very helpful, thanks again. good tip on pointing out the ring too
@52yamahar1
2 жыл бұрын
Couldn’t of made it any clearer, first time I’ve tried this and it’s worked a treat 👍🏻
@jerrodq9733
11 ай бұрын
heads up on the 2017 I have, the PDS bushing in the swingarm does have a small lip. So be careful when pressing it out that you use a socket that is small enough so that it doesn't catch on the smaller lip. I didn't see it at first but when i couldn't get it to press out I found this was the cause. It's not easily seen if dirty, and also it's quite recessed so it's hard to see. I know there is a lip on the right side, not sure on the left side.
@jesseklassen2017
5 жыл бұрын
That’s what I was thinking of doing. I got a long bolt instead of threaded rod. Good video dude!!👍👍
@johnhewer0
7 жыл бұрын
It was a while ago but think I started the bearing off by carefully taping them in with a rubber hammer. Then used the same socket method to press them fully in. Just be careful with the dust seals as they are extremely soft.
@wolkenhaube
6 жыл бұрын
maddog do not use hammer hits on the chassis
@wolkenhaube
6 жыл бұрын
maddog you ride 150 mph micro cuts will make you unsave
@obonnetfe1157
3 жыл бұрын
Very helpful video .. I just did it today on my 540 SXS ! Thank you
@bradhall3214
8 жыл бұрын
Thanks for posting this video, I just tried this on my KX and it worked great!
@Asken12345
8 жыл бұрын
Just a thought... if you put the big socket on he right (at 5:44) and the smaller on the left you can fit both the socket pushing and the bigger at once so you don't have to pull it apart to get the second one out.
@vinuezaer
7 жыл бұрын
Best one I've seen. Great explanations.
@kicekap
6 жыл бұрын
Great tutorial, can You explain me directions of pushing in and out the bearings? Thanks Mate
@peterpezzuto818
10 жыл бұрын
Great video, Thanks for posting this!
@abquix
4 жыл бұрын
Thanks man, really helpful
@alftorrisi8795
Жыл бұрын
Fantastic thank you very much
@pmfilmsUK
Жыл бұрын
Fantastic
@jflo2595
7 жыл бұрын
Thank you great video do you know how to put them back in for the new ones
@luisdiaz8942
7 жыл бұрын
very good idea and simple or easy extractor ...
@yonmoore
9 жыл бұрын
Thanks for posting!
@Runk3lsmcdougal
2 жыл бұрын
Awesome thanks
@PTG847
6 жыл бұрын
Is it normal on the right side with (side with no washers) for the final barrel to have some side to side movement?
@jordanheat8331
9 жыл бұрын
How come theres no sound?
@tiagosimoes5880
10 ай бұрын
Need mount kit in swingarm ktm quad. can give me sequence of pieces? tanks
@Sotirg
6 жыл бұрын
the other side does not have rings, no?. I bought the repair kit and only two come instead of four.. sorry for my english
@wolkenhaube
6 жыл бұрын
Soti Rg there are more uses for that... not only motorcycles... as i know some electro engines need to change the rings after 20 years of running.
@michail1963
6 жыл бұрын
Yup. I was also puzzled at first...yes only the sprocket side used both retaining rings.
Пікірлер: 32