You Are A Very Good Mechanic, And Instructor ! You Can Work On My Bike Any Time !
@Garage_Tinkerer
11 жыл бұрын
You don't have to remove the motor. You should be able to pull the shaft back enough to get at the motor side.
@kenholt8297
7 ай бұрын
WOW! When did Yamaha start making invisible rear tires?
@Garage_Tinkerer
12 жыл бұрын
Thank you very much.
@richardbrown440
6 жыл бұрын
Has any body changed the rubber boot on the driveshaft housing on a 2007 KAWASAKI NOMAD 1600 , if so did you have to remove the swing arm
@BikerFux
2 жыл бұрын
Andrew...thanks on this clip my 06 shadow now has 20000 on her was wondering if had to take it apart a grease the splines on rod to wheel
@lukasdolezal1297
6 жыл бұрын
Hi, I need your help. I put Rear End Gear on my m109r off because of the wheel removing but when I putted everything together I can't gear up 1st gear, there is weird sound is there any special shaft possition or what?... can you help me somehow please??
@kenmitchell3355
8 жыл бұрын
I have a 2007 Kawasaki Vulcan/Nomad 1600 with 10,700 miles on it. The manual is not clear on when to lube the drive shaft. I just changed the rear tire so I lube the splines where the tire mounts onto with moly. Should I have lubed the actual drive shaft to?
@MindBodySoulOk
11 жыл бұрын
So you can get the splines lubed with the motor on but not the universal joint correct? I'm not taking my motor off no way Jose.
@jonaug1
12 жыл бұрын
im workin on a kawasaki 750 vulcan and i was wonderin if u could do a vid on how to remove the motor from the frame im having some problems with it and i would appreciate the help
@invaderzim1265
2 жыл бұрын
What's that plastic thing you have on your hand? I need that as well, its has the measurement I need to read! Thanks! 02:36
@Garage_Tinkerer
2 жыл бұрын
It's an oil syringe.
@Roma-di5xf
10 жыл бұрын
Hey Andrew, I have a question if you don't mind assisting. I have an 85 XV1000 and I snapped my FD oil drain nut off. Luckily, I have a Maxim X parts bike and the FD seems to be exact so I replaced it. I noticed when I took out the shaft, it just popped out. When I put the new one in, all seemed fine. I had a hard time finding How To videos on how to do this so I want to make sure there wasn't anything else I missed. It seemed straight forward. Was I supposed to replace anything when re-installing this? Thanks
@Garage_Tinkerer
10 жыл бұрын
Sounds about right. There should be a spring at one end of the shaft to keep the lash at bay. As long as that is in there you should be good.
@Roma-di5xf
10 жыл бұрын
Thanks! Cheers
@NMOwen
9 жыл бұрын
Hi Andrew, I found your video because there is a very noticeable click/ticking noise coming from the final drive area of my bike (sounds like down in that unit) with every rotation of the wheel, whether clutch engaged or not. I ride a 1986 Honda Magna, 700cc, 18k miles. I am concerned about the noise for both safety and mechanical reasons. But I don't have the experience to know how warranted my concern is. Any ideas what could cause such a repetitive ticking/clicking sound? I am tempted to say it is only at low speeds. But I think that's just because as speed increases the engine noise drowns it out. It's probably still there, just not noticeable once over 20mph or so. My bike is my primary mode of transport. And I'm still riding it with this problem. But I don't want to be putting myself at a huge risk. Yet if it's something I could fix on my own, that would be welcome news too. Thanks for your videos, as well as any thoughts you might have on the above.
@kaluacrow8057
8 жыл бұрын
+N.M. Owen I've been told that when the rear wheel is not properly aligned or bolted up to the rear drive hub it can create that clicking sound you've mentioned. Try pulling the rear tire off and re-aligning it.
@NMOwen
8 жыл бұрын
KALUA CROW Thank you for this!!
@hgutierr
6 жыл бұрын
I am working on a 1981 Yamaha XV750 Virago. It's shaft driven too. I am taking everything apart and in my case the U-join is attached to the transmission on the engine with a nut. I am trying to remove it but I am having no luck. How did you remove the drive shaft from the engine on your bike? Thanks!
@Garage_Tinkerer
6 жыл бұрын
#25 in this diagram? Vwww.bikebandit.com/oem-parts/1981-yamaha-virago-750-xv750h/o/m156281#sch846435
@hgutierr
6 жыл бұрын
Thank you for prompt response! This info. helps a lot!! Worse case, I may need to order some parts from here. I am doing an electric motor conversion on this bike and this is where I am making the connection. Again, thank you!!
@roosterp.5662
5 жыл бұрын
My bike will turn on and run and go into gear but wont move at all and theres somewhat of a grinding noise. Just wondering if it could be the drive shaft?
@Garage_Tinkerer
5 жыл бұрын
Could be, could also be the clutch or transmission. Can you tell where the grinding is coming from? Clutch is the easiest to check and replace so I'd start there.
@sebs79
12 жыл бұрын
Dude what kind of oil you used?
@Garage_Tinkerer
12 жыл бұрын
90w Gear Oil.
@roosterp.5662
3 жыл бұрын
Whats molly bro?
@Garage_Tinkerer
3 жыл бұрын
Molybdenum disulfide grease. Commonly called molly.
Пікірлер: 30