In this video I go over Section 1.8 of Luke's Guide, Esteps and Flow Rate using Octoprint to save the new ESteps. This can be done with any software that allows you to connect to the printer, as long as you have a firmware that allows saving to the EPROM.
🛑Subscribe for more: www.KZitem.com/theedgeoftech...
🐱🏍Share this video with a friend:
• Section 1.8 Esteps and...
💾 Share this channel with a friend:
/ @theedgeoftech
GCode Used in this video:
M503 - Used to see the current settings of the printer, and get the ESteps
G1 E100 F100 - Used to advance 100mm of filament through the extruder
M92 E### - Used to change the ESteps to the value represented with the # symbols. For example if we want to change it to 100 steps, the code would be M92 E100. 95 ESteps would be M92 E95.
M500 - Saves the changes you made into the EPROM.
EStep Calculation:
100 (commanded Steps) divided by 98 (actual steps taken) = 1.02
1.02 x 93 (Current ESteps) = 94.86
95. is your new ESteps if you round up
Flow Rate Calculation using new .8 walls on the cube:
Value of all 8 measurements divided by 8 = Average Measurement.
.80 divided by average measurement multiplied by 100 = New Flow Rate.
Example:
.78+.80+.76+.79.+.80+.81+.75+.78 - 6.27 Equals Total Walls Measured
6.27/8=.783 - Total Walls Measured divided by 8 (8=total measurements taken, 2 on each side of the cube)
.8/.783 = 1.02 - Wall thickness (.8) divided by Average of Total Walls Measured (.783)
1.02x100=102. = 102 is the new flow rate.
Luke's Short throw Calibration Test Cube: www.thingiverse.com/thing:322...
Luke's Help Guide
support.th3dstudio.com/hc/en-...
Disclaimer: Some of these links go to one of my websites and some are affiliate links where I'll earn a small commission if you make a purchase at no additional cost to you. As an Amazon Associate I earn from qualifying purchases.
Ender 3 V2 Amazon: amzn.to/2OA9bug
Code: 07ZGQI2J to save some money!
Ender 3 V2 Amazon:amzn.to/3qRzLwb
Code: 07GZXYYD to save some money!
Decent Caliper for 3D Printing: amzn.to/3elcw8N
Ender 3 Pro on Amazon: amzn.to/3ak9BtS
Ender 3 direct from Creality:
Ender 3: www.creality3dofficial.com/co...
Ender 3 Pro: www.creality3dofficial.com/co...
The Edge of Tech Amazon Affiliate Store Front: www.amazon.com/shop/theedgeof...
Support the channel through these links!
PayPal
paypal.me/theedgeoftech
Patreon
/ theedgeoftech
Watch next - Luke Hatfields Help Guide Playlist - • Luke Hatfield's Help G...
Recommended Playlist - Community Showcase - • Community Showcase
Let’s connect:
Instagram: / theedgeoftech
Twitter: / theedgeofteck
Facebook: facebook.com/TheEdgeofTechOfficial
----------------------------------------Credits-----------------------------------------------------------
Music by Wicked Realm
Album - No More Fairy Tales
Song - Feed
/ @wickedrealm5507
Негізгі бет Ғылым және технология Section 1.8 Esteps and Flow Rate using Octoprint and Free Air Method
Пікірлер: 45