I like the video, I have been building rear diffs professionally for over 25 years. 2 things that are missing. 1st once you have your backlash correct, you need to add a little more shim to both sides of your carrier. This is called carrier bearing preload. Without this preload you carrier will get loose as the bearings break in. Same reason you have pinion preload. If that diff ever gets noisy, this is why. Once it does you will need to start over with new gears. I would say you need an additional 10-15 thousandths total. So half of that per side. 2- the side of the tooth I saw with the marking compound was the coast side, I couldn’t see the drive side.
@secondchancegarage9717
2 жыл бұрын
Thanks for the info. I’ll double check
@Bigdliloug48
Ай бұрын
When doing the preload on the pinion and career bearings, is it a good idea to do the checks with lightly oiled bearing or just set up with dry bearings?
@19antman55
11 ай бұрын
You made sense to me who has never done that before... Thank you 👍
@joevalenz7742
10 ай бұрын
Hello sir, after watching several videos of setting up the pinion gear-carrier group, your video is the Best straight forward video! Great job
@secondchancegarage9717
10 ай бұрын
Thanks. Appreciate it.
@daverobins182
9 ай бұрын
i did my posi 3 years ago, ive got side to side play now, im going to add some shims. thanks for the video, a little more volume would be great
@marchallaert7372
7 ай бұрын
Great tutorial! Thank you.
@jimbennett1519
3 жыл бұрын
Thanks man. Great video
@seanblackwell7060
3 жыл бұрын
Thanks
@nsboost
2 жыл бұрын
Crush sleeve is such a pain. Spacer is way easier
@larrydavis7286
Жыл бұрын
Hey. I have a question. I took a part a 1971 Olds cutlass rear end to replace the bearings I needed mark the bearing caps need to know how I can know I put the right one on the right bearing and if there are on up side down or right. They have arrow on the caps do the arrows point to the axle or toward the 3rd member.
@kensanders2776
Жыл бұрын
Very helpful thanks
@secondchancegarage9717
Жыл бұрын
Glad it helped
@MrCreativone
2 жыл бұрын
Where did you purchase the pinion depth tool
@secondchancegarage9717
11 ай бұрын
Summit
@440dragracer
Жыл бұрын
I’m building a 12 bolt, I didn’t use crush sleeve, I used a spacer and shims, what I’ve read pinion preload should be @25ip? Video was informative though
@secondchancegarage9717
Жыл бұрын
Thanks. I used what I had and I was unaware of spacers when I did it. Crush sleeve is what I’ve always done. 👍🏻
@Timgrantham66
2 жыл бұрын
Is this a factory locker?
@secondchancegarage9717
11 ай бұрын
No
@conradosantiago2330
2 жыл бұрын
How to Chang the guiars of a spring posi for a thing axol to a thicker one
@audyanaya7052
2 жыл бұрын
Buenos días me gustaría tener el vídeo en español gracias
@charliepowers5265
Жыл бұрын
I can't watch this guy i feel asleep.
@secondchancegarage9717
Жыл бұрын
LOL. I have channels saved just for this. When I need a nap. Thanks though
Пікірлер: 25