Make all your vertical cuts first , then the horizontal cuts take a hand full of boards off at active instead of one at a time . Less walking around the machine means more time with the saw in the cut ( turning a profit )
@ismailbakar2488
3 жыл бұрын
be careful with your feet ... just a few inches from the cutter's eye..😪
@triktutorial
3 жыл бұрын
dinamonya berapa hp om?
@noobpvptv5176
6 жыл бұрын
If you start with your virticle cut first, when you move your horizontal cut forward you won't have to go around the mill to clear boards
@brigitteangerer1678
9 жыл бұрын
Einfach genial, sicher viel arbeit gewesen. Geschickter Kerl!
@richardbruce8111
3 жыл бұрын
please sir get a guard for your feet!
@helgeschneider1
3 жыл бұрын
Thank you for your worry, but i made something to potect my feet. My feet are not so close it looks like, they are nearly 1 meter away. This was my first try and it was not finished yet.
@triboysmeubel
3 жыл бұрын
Mantap?
@stinceldorin27
9 жыл бұрын
Hi my friend ! What it s the speed of the motor ? 1500 rpm or 3000rpm , and the power, and size of blade ! Tanks very much!
@helgeschneider1
9 жыл бұрын
+stincel dorin 1500 rpm and a 50 cm diameter blade. You're welcome!
@helgeschneider1
9 жыл бұрын
+stincel dorin The Motor has 7,5 kW
@haraldstein9130
3 жыл бұрын
@@helgeschneider1 Junger Mann,wie ist das Blatt befestigt. Kein Flansch und Mutter?
@helgeschneider1
3 жыл бұрын
@@haraldstein9130 Mit Senkkopfschtauben am Flansch befestigt, das Blatt muss ubterhalb glatt sein, es dürfen keine Schrauben vorstehen
@haraldstein9130
3 жыл бұрын
@@helgeschneider1 dann hat das Blatt keine 30 oder 40mm bohrung für die Welle?
@drkockie
8 жыл бұрын
What blade did you use en where did you get it from? (I live near the border of Germany; I can speak and read German, just not write it properly....)
@emmerichhopfer4847
8 жыл бұрын
+Maarten KocEDESSÖ HM Sägeblatt Brennholzsägeblatt 500 x 30 mm LWZ und ich kaufte es bei ebay
@drkockie
8 жыл бұрын
+Emmerich Hopfer Vielen dank! How did you mount it on the motor? Do you have a picture of the underside of the blade when it is mounted?
@emmerichhopfer4847
8 жыл бұрын
+Maarten Kock Das Sägeblatt ist mit Senkkopfschrauben befestigt und muss unten komplett eben sein. Musste deshalb extra Löcher bohren. Die Höhe des Drehpunkts über dem Sägeblatt muss genau dem Radius des Sägeblattes entsprechen.
@drkockie
8 жыл бұрын
+Emmerich Hopfer How did you drill the holes? Is the blade not to hard to drill trough?
@emmerichhopfer4847
8 жыл бұрын
+Maarten Kock : Es geht gar nicht so schwer.Wichtig ist dass Du während des bohrens mit Öl kühlst. Habe 6 Löcher mit HSS 8mm gebohrt und zum Versenken der Schrauben einen 16 mm Bohrer genommen. Das Teil zum Befestigen auf dem Motor hab ich mir selber gedreht.
Пікірлер: 30